Kramer KDS-SW2-EN7 User manual

KDS-SW2-EN7 Quick Start
P/N:
2900- 301547QS
Rev:
1
Scan for full manual
KDS-SW2-EN7 Quick Start Guide
This guide helps you installand use your KDS-SW2-EN7 for the first time.
Go to www.kramerav.com/downloads/KDS-SW2-EN7to download the latest user manual andcheck if
firmware upgrades are available.
Step 1: Check what’s in the box
KDS-SW2-EN7 2x1 4K AVoIP Switcher Encoder
2 Bracket sets
1 Quick start guide
Step 2: Get to know your KDS-SW2-EN7
#
Feature
Function
1
HDMI IN Connector
Connect to an HDMI acceptor.
2
USB-C IN Port
Connect to a USB-C source.
•When powered by a Kramer 24V power supply (optional), charges sources (that
support USB Power Delivery 2.0) up to 60W.
3
LCD Display
Use for device configuration such as input selection, unique channel/AV stream setting
and EDID.
4
Menu Navigation
Button

Press to return to the previous menu.

Press to move up to the next configuration parameter.

Press to go to the next menu.

Press to move down to the next configuration parameter.
Enter
Press to accept changes.
5
LINK LED
See LED Functionality.
6
NET LED
See LED Functionality.
7
ON LED
See LED Functionality.
#
Feature
Function
8
24V/5A DC Connector
Connect to the power adapter (purchased separately).
9
RESET Recessed Button
Press and hold for 10 seconds to reset the device to its factory default values. All LEDs flash.
10
LAN MEDIA 1G(PoE) RJ-45
Port
Unicast: connect for streaming either directly to a decoder or via LAN.
Multicast: connect to multiple decoders or connect to one decoder to which multiple
decoders are daisy-chained via SERVICE (1G) port.

#
Feature
Function
11
LAN SERVICE 1G RJ-45
Port
Used optionally for physical separation between AV and command streams to separate LAN
for security and reliability purposes.
12
RS-232 3-pin Terminal Block
Connector
Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even
when no AV signal is extended).
13
AUDIO IN/OUT 5-pin
Terminal Block Connector
Connect to a balanced analog stereo audio source/acceptor.
14
IR 3.5 Mini Jack
Connect to an IR sensor or emitter for bi-directional signal extension (even when no AV
signal is extended). Expected voltage for IR receiver - (3.3V).
15
USB Type A Charging Ports
(1 and 2)
Connect to USB devices, for example, to a speakerphone and webcam.
16
HOST USB Type B Port
Connect to a USB host.
17
HDMI OUT Connector
Connect to loop the signal.
LED Functionality
KDS-SW2-EN7 LEDs function as follows:
LED
Color
Definition
LINK LED
Lights Green
A link is established between KDS-SW2-EN7 and the decoder is
transmitting A/V signals.
Flashes Green
A signal is established, and a problem is detected
NET LED
Off
No IP address is acquired.
Lights green
A valid IP address has been acquired.
Flashes Green very fast (for 60sec)
A device identification command is sent (Flag me).
Lights Yellow
Device falls back to default IP address.
Lights Red
Security is blocking IP access.
ON LED
Flashes Red
On fallback address acquiring, device ‘ON’ LED flashes continuously in
slow 0.5/10sec cadence
Lights Green
When power is on.
Flashes Green Slowly
Device is in standby mode.
Flashes green fast
FW is downloaded in the background.
Flashes Green very fast (for 60sec)
A device identification command is sent (Flag me).
Lights Yellow
Device falls back to default IP address
Lights Red
Security is blocking IP access.
Post reboot, all LEDs light for 3 seconds then return to their normal LED display mode.
Step 3: Mount KDS-SW2-EN7
Install KDS-SW2-EN7 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/KDS-SW2-EN7).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/KDS-SW2-EN7).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your KDS-SW2-EN7 and KDS-DEC7.
KDS-SW2-EN7 and KDS-DEC7 can stream 4K video, requiring a gigabit Ethernet switch for high quality performance, since the
maximum momentary transfer rate can reach 850Mbps. We recommend using AVoIP Ethernet switches that support: Multicast
forwarding or filtering, IGMP Snooping, IGMP Querier, IGMP snooping fast leave and Jumbo frame (8000 bytes or larger).
Connecting the audio input/output
To a balanced
stereo audio
source/acceptor:
To an unbalanced
stereo audio
acceptor:
To an unbalanced
stereo audio source:
To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/KDS-SW2-EN7.
Using third-party cables may cause damage!
Step 5: Connect power
By-default, the device uses PoE for powering the device.
Optionally, you can separately purchase a power adapter to connect to the product and plug into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPIO ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Operate KDS-SW2-EN7
Allocating the IP Address via LCD screen menu
KDS-SW2-EN7 IP default address is 192.168.1.39. By default, DHCP is enabled, and assigns an IP address to the device. If
DHCP Server is not available, for example, in case a device is connected directly to the laptop, that device gets the default IP
address. If this IP addresses is already in use, the system searches for a random unique IP in the range of 192.168.X.Y. the
allocated IP address can be identified using the LCD screen menu.
To allocate the IP address via LCD screen Menu:
1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights
green, and the LINK LED flashes (indicating that no streaming activity is detected).
2. Use the Navigation button to view the assigned IP address on the LCD screen:
▪DEV STATUS > LAN1 Status
▪DEV STATUS > LAN2 Status (if the Service port connected as well).
Setting Channel Number
Each encoder requires a unique channel number, and the connected decoders should be tuned to that encoder channel. You
can set the channel number via the LCD screen menu or the embedded web pages.
To set the channel number for KDS-SW2-EN7 via LCD screen menu:
1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights
green, and the LINK LED flashes (indicating that no streaming activity is detected).
2. In the LCD screen menu, go to DEV SETTINGS > CH DEFINE.
3. Change channel number using arrow buttons and set a unique channel number.
4. Press Enter to save your selection.
To set the channel number via web pages:
1. Connect the KDS-SW2-EN7 Ethernet port to the network and power the device.
2. Access the embedded web pages.
3. In the Main page:
For KDS-SW2-EN7:
▪Go to AV Routing page.
▪Select Channel ID and define the channel ID number.