Kramer KT-107 User manual

KT-107 Quick Start (P/N: 2900-300935QS REV 3)
P/N:
2 9 0 0 - 3 0 0 9 3 5 QS
Rev:
3
Scan for full manual
KT-107 Quick Start Guide
This guide helps you install and use your KT-107 for the first time.
Go to www.kramerav.com/downloads/KT-107 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
KT-107 Touch Panel
Tabletop mount
On-wall mount unit
1 Quick start guide
1 C-USB/MicroB cable
AC/DC adapter
Installation screws
Panel mount plate
1 right-angle OTG USB cable
Step 2: Get to know your KT-107
#
Feature
Function
1
Hidden Reset Button
Located on top-side. Insert a pin and hold for a few seconds to reset KT-107.
2
Light Sensor
Automatically adjusts the screen brightness according to the room lighting conditions.
3
Activity RGB LED
Lights green when powered, flashes green when charging the battery, lights red when
camera on.
4
Camera
For remote room viewing or video conferencing.
5
Microphone
For audio communication, recording or conferencing.
6
Speakers
To output the sound.
7
Control Button
Press and hold (for 2 seconds) to open the pop-up menu which lets you power down
the unit, reboot it or return to the Home-page. The Control button is password
protected (default: Kramer).
8
Tabletop Mount Connector
For connecting to the tabletop mount.
9
Cover
Covers the wall mount connections and power button.
10
Power Button
Press to power on the KT-107. When powered, press brieflyto open the pop-up menu
and power down the device, reboot it or return to the Home-page. Press and hold to
power down the device immediately. This button is also used for firmware upgrade.
11
Volume-up Button
Used forfirmware upgrade. Use also to increase KT-107 speaker volume.
12
Micro USB Port
For connecting to an adjacent on-wall USB device and for firmware upgrade.

#
Feature
Function
13
Flat Cable Connector
For connecting to the on-wall mount unit.
14
Connecting Holes
For connecting to thetabletop mount or the panel mountplate.
To prevent potential damage to the Touch Panel, use only Kramer supplied screws
and mounts.
Step 3: Mounting the KT-107
Mounting on a table using one of the following options:
Portable Mount: place the tabletop mount on the table. Connected cables remain visible and the table remains intact.
Secure Mount: secure the tabletop mount to the table as follows:
1. Measure the exact location on the surface of the table where you want to install the KT-107.
2. Drill a hole in the table and optionally cut the cable pass-through opening according to the cut-out dimensions defined in
the user manual.
3. Secure the tabletop mount to the table using the M5x60 secure screw.
4. Connect the Ethernet port to a PoE-enabled source. Optionally, you can connect the power adapter too (as backup).
5. Replace the appropriate cover and place the KT-107 over the tabletop mount (the Touch Panel is magnetically held in
place), by first inserting the lower part of the Touch Panel then carefully laying the KT-107 in place.
6. Wait for the Home-page to load and then secure the KT-107 to the tabletop mount from the rear side (using 2 M2x4
screws, supplied with the unit).
7. Optionally, lock the tabletop mount with a Kensington locker (not supplied).
Mounting on the wall:
Before mounting KT-107 on a wall, install an in-wall junction box (recommended boxes are listed in the user manual)
1. Attach the on-wall mount unit to the installed junction box (top side up see indication arrows on unit).
Connect Ethernet and/or power cables and optionally, insert the right-angle USB cable (supplied) for connecting to an
adjacent external USB device.
2. Screw the 4 wall-mounting screws (supplied) through the screw openings.
The various screw openings fit various types of wall junction boxes.
3. On the rear side of the KT-107, remove the screw cover and the cover (by slightly pressing downwards and then pulling
out) and set aside.
4. Attach the panel mount plate to the rear side of the KT-107 (using 4 M2x4 screws, supplied).
5. Connect the flat cable from the on-wall mount
(attached to the in-wall junction box) to the connector
on the rear of KT-107.
6. Hang the KT-107 on the wall by sliding the tabs on the
attached panel mount plate over the grooves on the
on-wall mount unit.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.

Step 4: Customizing the KT-107 settings
The Settings page is accessible from the Home-page and enables customizing the KT-107 settings:
To modify date and time settings:
1. In the Home-page, click Settings.
2. Scroll down to the System area and click
Date & time.
3. Enable Automatic date & time to derive the date
and time from the Network. When disabled, enter
the date and time manually.
4. Select the time format.
To configure the Boot Start App:
1. In the Home page click Settings.
2. Click Control.
3. Click Select Boot Start App and select one of the
available Apps (Kramer Control or K-Touch) to
appear upon startup, or select None.
To modify display settings:
1. In the Home-page, click Settings.
2. Select Display.
3. Set the following (as required):
Brightness: Brightness level, adaptive brightness
Status Bar: Show/hide lower and/or top status
bar
Auto Sleep: Sleep timeout
To modify Control button settings:
1. In the Home-page, click Settings.
2. Select Control.
3. Enable or disable the Control button (Kramer
Logo touch).
4. Set Control button password protected to be
enabled/disabled.
To change the password of the control button:
1. In the Home-page, click Settings.
2. Select Control.
3. Click Change password (default: Kramer).
4. Follow the instructions in the Password Set window.

For KT-107 model: FCC-ID-R8S-KT-107
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation of the device is subject to the following conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation
Recommendations for safe exposure to non-ionizing radiation: Only use the device at least 20 centimeters away from yourbody.
Technical Specifications:
Tabletop Mount Ports:
1 1000/100/10BaseT Ethernet on RJ-45 connector; 1 micro USB 2.0
2-pin terminal block for DC power supply
On-wall Mount Ports:
1 1000/100/10BaseT Ethernet on RJ-45 connector
1 2-pin terminal block connector for DC power supply
Speakers:
2x1 W, 8 ohm
Microphone:
-42dB ±3dB @ 1kHz sensitivity
CPU Performance:
1.6GHz Quad Core, GPU, 2GB RAM, 16GB Flash
OS Software:
Android 6.0.1
Multi Touch:
10 points, 2-finger gesture
Display:
7” IPS, 1280x800 RGB pixels, 16:10 aspect ratio, ±80° horizontal/vertical viewing angles, 400cd/m2
brightness, 800:1 contrast ratio
Video Format:
Decoding: H.265/HEVC; H.264/AVC; MPEG-1/2/4; DivX 3/4/5/6; MVC; GOOGLE VP8; VC-1; H.263;
SORENSONSPARK; ON2 VP6; MOTION JPEG; Encoding:H.264/AVC
Ethernet Port:
10/100/1000Mbps PoE LAN
Wireless Communication:
Wi-Fi 802.11 b/g/n/ac, Bluetooth 4.0
Camera:
Front, 2M pixels, HD 720p
Battery:
Rechargeable, supports up to 3 hours of Wi-Fi operation
Controls:
Hidden reset button, power button, volume-up button
Touch panel status LED: flashes green during charging, green for fullycharged, red for camera on
Power Inputs:
Power over Ethernet (complies with IEEE802.3af and IEEE802.3at PoE standards), power supply unit
Power Consumption:
5V DC, 3A
Operating Temperature:
0° to +40°C (32° to 104°F)
Storage Temperature:
-10°to +55°C (14° to 131°F)
Humidity:
10% to 90%, RHL non-condensing
Case Design:
Black body and cover
Dimensions:
Shipping dimensions:22.4cm x 13cm x 20.6cm (8.8" x 5.12" x 8.1"), W, D, H
Touch panel: 17.8cm x 1.3cm x 13cm (7" x 0.51" x 5.12"),W, D, H
Tabletop mount: 18.5cm x 10.7cm x 12.4cm (7.28" x 4.2" x 4.88"), W, D, H
Panel mount plate: 14.6cm x3.7cm x 9.2cm (5.75" x 1.46" x 3.62"), W, D, H
On-wall mount unit: 14.6cm x 1.1cm x 9.1cm (5.75" x 0.43" x 3.58"), W, D, H
Weight:
Shipping weight: 1.8kg (3.97lbs) approx.; Touch panel: 0.37kg (0.8lbs) approx.
Included Accessories:
Power supply unit adapter (5V, 4.0A AC/DC), tabletop mount, on-wall mount unit,
panel-mount plate, right-angle OTG USB cable, installation screws
Certifications:
CE/CB, FCC, ROHS, REACH
Mounting Options:
Table top (with tabletop mount unit), on-wall (with mount unit and panel mount plate)
Specifications are subject to change without notice atwww.kramerav.com