Kramer KDS-10 User manual

KDS-10 Quick Start
P/N:
2900- 301387QS
Rev:
1
Scan for full manual
KDS-10 Quick Start Guide
This guide helps you install and use your KDS-10 for the first time.
Go to www.kramerav.com/downloads/KDS-10 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
KDS-10 4K Video Encoder/Decoder
1 Power cord
4 Rubber feet
1 Quick start guide
Step 2: Get to know your KDS-10
FRONT PANEL BACK PANEL
#
Feature
Function
1
USB Type A Port
For future use.
2
POWER LED
Lights when the device is powered ON.
Encoder Mode
Decoder Mode
3
LINK LEDs (1 & 2)
Each LED represents an HDMI™input
status.
White Flashing = Device booting up.
Red = Error.
•HDMI In not connected.
•Ethernet not connected.
Blue = The stream is administratively
stopped via webpage interface.
Purple = Waiting for an HDMI input
signal.
Green = HDMI input signal detected.
LED 1 represents HDMI output. LED 2 is
non-functional.
White Flashing = Device booting up.
Red = Error.
•HDMI Out not connected.
•Ethernet not connected.
Blue = The stream is administratively
stopped via webpage interface.
Purple = Waiting for a connection to be
established.
Green = HDMI output signal detected.
4
IN HDMI Connectors (1 to 2)
Connect to up to 2 HDMI sources.
5
OUT HDMI Connector
Connect to an HDMI acceptor.
6
LAN RJ-45 Connector
Connect to the network using recommended Kramer cables.
7
AUDIO IN/OUT Balanced Stereo Audio
5-pin Terminal Block Connector
Connect to an analog audio acceptor or receiver.
8
CTRL Mini USB Connector
Connect to PC to send P3K commands to control device.
9
RESET button
Press and hold while powering on the device to reset to factory default parameters.
10
12V DC Connector
Connect to the power adapter.
Step 3: Mount KDS-10
Install KDS-10 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (not included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/KDS-10).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/KDS-10).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your KDS-10.
Connecting audio output
Connecting audio Inputs
Connecting the audio
output to a balanced
stereo audio acceptor:
Connecting the audio
output to an unbalanced
stereo audio acceptor:
Connecting a balanced
stereo audio source to the
balanced input
Connecting an unbalanced
stereo audio source to the
balanced input
For optimal performance, use the recommended Kramer cables available at www.kramerav.com/product/KDS-10.
Using third-party cables may cause damage!
Step 5: Connect power
Connect the power cord to KDS-10 and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Operate KDS-10
Operate KDS-10 via:
•Remotely, by Mini USB serial
commands transmitted by a
touch screen system, PC, or
other serial controller
•Embedded web pages via the
Ethernet
RS-232 Control / Protocol 3000
Baud Rate:
115,200
Parity:
None
Data Bits:
8
Command Format:
ASCII
Stop Bits:
1
Example: (Switch video input 2 to output 4): #V 2>4<CR>
Default Ethernet Parameters
IP Address:
192.168.1.39
UDP Port #:
50000
Subnet Mask:
255.255.0.0
TCP Port #:
5000
Gateway:
0.0.0.0.
Default Username:
Admin
Default Password:
Admin
To control via the Web pages:
1. Connect the KDS-10 Ethernet port.
2. Access the embedded Web pages.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.