Kraus Bellucci KGF1-33 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. September 10, 2019
Bellucci™ Quartz Granite
Composite Farmhouse Sink
KGF1-30 / KGF1-33
KGF2-30 / KGF2-33
R
INSTALLATION GUIDE

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
2

Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged during shipping.
·Observe all plumbing and building codes according to your state requirements.
·Additional floor and wall preparation may be required to avoid damaging the sink.
·Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse base cabinets
should be 3" larger than the actual size of the sink.
·Not recommended to be installed with laminate countertop.
3
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a
Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to
install all Kraus products by hiring a licensed professional.
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Granite Farmhouse
Sinks with countertop materials other than wood, marble or granite.
Phillips Screwdriver Pencil
Tape Measure Screwdriver Level
Safety Goggles Silicone Adhesive Jig Saw Acetone
Drill
ACETONE

44
KGF1-30
29 3/4" x 20 3/4" x 9 3/8”
Min Cabinet Size: 33”
KGF1-33
32 7/8" x 20 3/4" x 9 3/8”
Min Cabinet Size: 36”
29 3/4" 755mm
20 3/4"
527mm
17"
431.2mm
10"
254mm
32 7/8" 835mm
30" 762mm
20 3/4"
527mm
17"
431.2mm
10"
254mm
9 3/8"
239mm
9 3/8"
239mm
Parts List
·Kitchen Sink
·Cutting Board
·Mounting Clips
Dimensions
KGF2-30
29 3/4" x 20 3/4" x 9 3/8”
Min Cabinet Size: 33”
KGF2-33
32 7/8" x 20 3/4" x 9 3/8”
Min Cabinet Size: 36”
27" 686mm
29 3/4" 755mm
20 3/4"
527mm
17"
431.2mm
10"
254mm
32 7/8" 835mm
30" 762mm
20 3/4"
527mm
17"
431.2mm
10"
254mm
9 3/8"
239mm
9 3/8"
239mm
27" 686mm

55
1. Determine Reveal Type
·Due to the custom nature of this type of installation, no cutout
template is included. It is recommended that the sink is installed with a
1/8" countertop reveal. It is further recommended that the installer(s)
discuss this with the customer and agree that this finished appearance
is the desired effect. Kraus is not responsible for improper sink or
countertop installations.
KRAUS Recommended Installation Type
Countertop
Silicone Caulk
(not furnished)
Sink
Mounting Clip
Fastener
(not furnished)
1/8"

66
2. Cut Countertop
·Cut the opening in the countertop
NOTE: Please use the
appropriate saw that best
fits your countertop material

7
4. Set up Mounting Baskets
·Turn countertop over and align with countertop. Decide location for
mounting brackets.
·Mounting holes should be 1/2" from edge of sink.
3. Cut Cabinet Front
·Measure height of apron front. Add 1/16" to the dimension when you
mark base cabinet front cutout. Use jigsaw to cut.
1/2"
(13mm)

8
5. Drill Hole in Countertop
·Drill 1/4" diameter x 1/2" deep hole in the countertop.
1/4" 1/2"

9
6. Install Anchors
·Insert anchors into drilled holes and lightly tap with a hammer until
flush.

10
7. Secure Sink to Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the
sink. Check the alignment of the sink to the cutout in the countertop.
Place sink over cutout hole and press firmly.