Kraus Cirrus FUS-13103 User manual

INSTALLATION MANUAL
Cirrus 8” Widespread Basin Faucet
FUS-13103
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 16, 2016

1
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old faucet
to release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Max countertop thickness: 1-3/8”
Tools you will need:
Adjustable Wrench Safety Goggles
Plumber’s Putty
(optional)
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Bucket
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]

3
FUS-13103 Diagram and Parts List
S1
S2
S3
C
A
D
E
G
H
J
K
Q
T
R
L
M
N
PO
I
B
F
A. Hot Handle
B. Set Screw
C. Cover Button
D. Base Metal Ring
E. Base O-Ring
(factory-installed in base metal ring)
F. Rubber Washer
G. Mounting Nut
H. Hot Valve
I. Spout
J. Spout Base
T. Hex Wrench
K. Base O-Ring
(factory-installed in spout base)
L. Rubber Washer
M. Mounting Nut
N. T-Union Clip
O. T-Union
P. Waterlines
Q. Cold Valve
R. Cold Handle
S. Aerator Assembly
S1.Aerator Washer
S2.Aerator
S3.Aerator Cover

4
Faucet Dimensions

5
Lift Rod Drain Diagram and Parts List
a
b
c
d
e
f
g
ijklm
o
n
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Clip
n. Lift Pole Rod
o. Lift Pole Knob

6
1
2
3
4
5
6
7
91011 12
13
15
14
8

7
Step 1: Install lift pole rod and knob
Remove lift pole knob (o) and clip
(m) from lift pole rod (n). Insert lift
pole rod (n), threads up, into the
base of the spout (I). Place lift pole
knob (o) in the back opening of
the spout (I). Connect lift pole rod
(n) to lift pole knob (o) and tighten
Step 2: Remove mounting hardware from spout
Remove mounting nut (M) and
rubber washer (L) from spout (I)
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3

8
Step 3: Install spout
Install spout (I) through predrilled
hole in sink or countertop with
spout base (J), base O-ring (K), and
lift pole rod (n) attached. Attach
rubber washer (L), and mounting
nut (M)
Step 4: Secure Spout
Adjust spout (I) to proper position
and tighten mounting nut (M)
with adjustable wrench. Install
t-union (O) onto supply line of
spout (I). Attach t-union clip (N) to
secure t-union (O)
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
I
I
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
I
I
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3

9
Step 5: Remove hot & cold handles, and base metal rings
Remove cover button (C) from
handle (R) and loosen set screw
(B) with hex wrench (T). Remove
handle (R), then remove base
metal ring (D) from valve (Q).
Insert valve (Q) into hole (Hot: Left,
Cold: Right) from underneath.
Repeat steps for second handle (A)
and valve (H)
Step 6 : Secure valves
Connect base metal ring (D)
onto valve from above. Tighten
mounting nut (G) on valve (Q)
from underneath with adjustable
wrench until snug. Reinstall
handle (R), tighten set screw
(B), and insert cover button (C).
Repeat steps for second handle
(A) and valve (H)
I
o
I
o
n
n
m
R
R
DC
F
D
D
F
G
Q
G
Q
B
CB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3
I
o
I
o
n
n
m
RR
DC
F
D
D
F
G
Q
G
Q
BCB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3
I
o
I
o
n
n
m
R
R
DC
F
D
D
F
G
Q
G
Q
B
CB
G
Q
1
II
M
O
N
J
K
L
M
n
L
M
Q
P
O
H
S1
S2
S3