Kruger KCE 240 M Instruction manual

MAINTENANCE
Before carry out cleaning or maintenance, disconnect the main electrical supply to
the fan by means of a double pole switch or remove the plug.
Remove the grille.
Clean the grille using lukewarm water neutral detergent and rinse with clean
water.
Wipe the main body with cloth and neutral detergent.
Fit the grille back when it is dry.
Note :
When power cord is replaced, the cord diameter should not be less than 0.5mm2
and it must be double covered and must use the fixing terminal and special tools
to work.
Do not put fingers into To prevent electric shocks, do not
the grille spray water near the ventilation fan
BREAKDOWN REPAIR
Phenomena
Check
Method
Fan blades not running
when the power is on.
1. If the fuse is broken
1. Ask for repair
2. If the fan blades are
blocked ( by cockroaches)
2. Remove and clean
the grille
Specification and sizes of parts
Accessories: screw: (#10x25)~ 5 pcs
Model
Hz
Watt
RPM
F.L.A
CMH
dB (A)
Kg
KCE 240M
60
35
1140
0.15
187
40
3.4
* dB (A) –Sound pressure level at 1 meter.
General Instructions
KCE 240 M
IGB027.0/0603
65 198
300
240
300
103.5
KRUGER GROUP
SINGAPORE
Kruger Ventilation Industries Pte Ltd
No. 17, Tuas Avenue 10
Singapore 639141
Tel. [phone] –Fax [phone]
MALAYSIA
Kruvent Industries (M) Sdn Bhd
Lot 8, Jalan Perusahaan 2 Batu Caves
Industrial Area, 68100 Batu Caves Selangor
Tel. [phone] –Fax [phone]
BEIJING
Bejing Kruger Ventilation Co. Ltd
No. 1A South Industry Area
Beijing Economical And Technological
Development Area, Beijing China 100176
Tel. [phone] –Fax [phone]
HONG KONG
Kruger Ventilation (Hong Kong) Limited
Flat C, 9/F,
Yeung Yiu Chung (No. 8) Industrial Building,
20 Wang Hoi Road,
Kowloon Bay, Kowloon, Hong Kong
Tel. [phone] –Fax [phone]
WUHAN
Wuhan Kruger Ventilation Co. Ltd
Xincheng Road 10, South Dongwu Ave,
Dongxihu District, Wuhan, Hubei, P.R.China 430040
Tel. [phone] –Fax [phone]
PHILIPPINES
Kruger M&E Industries Corporation
FAPI Compound, E. Rodriguez Ave.
Tunasan, Muntinlupa City, Philippines 1773
Tel. [phone] –Fax [phone]
INDONESIA
P.T. Kruger Ventilation Indonesia
JL. Teuku Umar No.20
Karawaci –Tangerang 15115, Indonesia
Tel. [phone] –Fax [phone]
KOREA
Neomate Technology & Consulting Co. Ltd
2-1010, Ace High City B/D, Mullae-dong 3-ga
Yeongdeungpo-gu, Seoul, Korea, 150-972
Tel. [phone] –Fax [phone]
DUBAI
Kruger Ventilation Industries, Gulf Branch
Jebel Ali Free Zone Area (JAFZA)
Near Roundabout 8, Warehouse No. RA08FC05
P.O. Box No. 262949
Tel. [phone] –Fax [phone]
SINGAPORE
Kruger Engineering Pte Ltd
No. 17, Tuas Avenue 10
Singapore 639141
Tel. [phone] –Fax [phone]
THAILAND
Kruger Ventilation Ind. (Thailand) Co. Ltd
30/105 Moo 1 Sinsakorn Industrial Estate
Chetsadawithi Road, Khok Kham Mueng,
Sakuthsakorn 74000, Thailand
Tel. [phone] –Fax [phone]
GUANGZHOU
Guangzhou Kruger Ventilation Co. Ltd
No. 9 Huahui Road, Huashan
Huadu, Guangzhou, P.R. China
Tel. [phone] –Fax [phone]
SHANGHAI
Shanghai Kruger Ventilation Co. Ltd
No. 500 Yuanguo Road, Anting, Jiading,
Shanghai 201814, P.R. China
Tel. [phone] –Fax [phone]
TAIPEI
Kruger Ventilation (Taiwan) Co. Ltd
No. 157, Ping-an Rd, Hengfeng Village,
Dayuan Shiang Taoyuan County 337, Taiwan (ROC)
Tel. [phone] –Fax [phone]
AUSTRALIA
S&P-Kruger Australia Pty Ltd
2 Cunningham St
Moorebank N.S.W. 2170
Tel. [phone] –Fax [phone]
INDIA
Kruger Ventilation Industries (India) Pvt Ltd
Kruger Centre, Mumbai-Nasik Highway,
Atgaon, Shahapur, Thane 421304, Maharashtra, India
Tel. [phone] –Fax [phone]
VIETNAM
Kruger Ventilation Industries Pte Ltd
(Vietnam Representative Office)
4th Floor, HHM Office Building, 157-159 Xuan Hong St,
Tan Binh Dist, Hochiminh City, Vietnam
Tel. [phone] –Fax [phone]
Ø99

“KRUGER” industrial and professional ventilators KCE Series, are components to be
installed in plants or building to create ventilation systems. Correct installation is
essential for the health and safety of people during operation of the appliance.
Therefore the regulations indicated in these instructions must be observed and the
mechanical protections must be prearranged.
If not properly installed the appliance may cause the risk of contact with the rotating
fan, with consequent collision and abrasion. In addition, if it is not wired correctly, it
may present risks related to electrical material. Should the appliance be required to
operate in isolation i.e in laboratory tests; it is necessary to block it appropriately
and prearrange the protections to avoid contact with the rotating parts. Room
temperature must not exceed 55°c.
It is best to install appliance as far as possible from areas usually occupied by people
to avoid accessibility and to reduce exposure to noise.
Transport This appliance must not be overturn and the packing must not be
deformed during transport. If the gross weight indicated on the
package is over 10 kg, the package must be carried manually by
more than one person. Appliance arranged on wooden-pallets must
be moved with a transpallet.
Storage The appliance should be stored in a dry place in their original
packing. Appliances packed in cardboard boxes may be stored on
top of one another up to a maximum of 2 meters, when not
otherwise indicated on the package. Appliances on pallets which
are placed in view cannot be stacked. After removing the packing,
check the integrity of the appliance. In case of doubt, do not use
the appliance and contact us. Packing elements (plastic bags, foam
rubber, nails, etc) must be kept out of the reach of children as they
are a potential source of danger.
Installation
When installation, note the following precautions :-
- remove packing and ensure the appliance is not damaged.
- Check that your electrical voltage and frequence correspond to those marked on
the rating label.
- Do not start or operate the fan unless the protection grille are in place.
- Install the fan before building the ceiling, it shall be installed where it is durable to
support the weight of the fan.
- The adopted material for ceiling shall be strengthened and resonance-resistance
(e.g. plaster board, celotax board)
- To prevent water from flowing back to the bathroom, tilt down the pipe to outdoor
for 1° to 2°.
- Select the exhaust-hole cover properly to avoid loud noise.
- Install height not lower than 2.5m.
Do not install it near gas
stove, above cooker or in
a place of high temp. over
40°C.
To improve the fan
efficiency in a closed
room, set up a convective
windows of 400 sq.cm in
opposite size to the fan.
Make sure to keep the
inspection port
- Do not distribute the pipe according to the following ways or it will be wind, loud
noise and the counter flow board cannot be opened.
(1) Overbent (2) Too many
bends on pipe
(3) Exhaust bend
pipe too close to
the main body.
(4) Connecting pipe
is shrunk
Installation Instruction
1. Frame Installation
Use strengthened frame to
support the whole weight of the
main body.
Woodframe use : 30 x 30 mm
Inner size : 250 x 250 mm
2. Connecting Pipe
Put the body into the fixing
frame, make a mark on it as per
the hole position shown in the
arrow and remove the body
(fig.1).
Tighten the wood screw at the
mark (fig.2).
3. Main Body Installation
Insert the main body aligned
with connecting pipe. Fix it
temporally by wind screw.
Connect the pipe with main
body tightly and fixed it by
additional screws #10x25 (5
pcs).
4. Connecting & Exhaust pipe
Seal up the connecting place by
adhesive tap or joint mixture.
Tilt down the exhaust pipe to
outdoor about 1° or 2°.
5. Electrical Distribution
Choose the corresponding wiring
diagram per your purchased
model.
A –normal model
B –remote control model
6. Ceiling Installation
Keep a space of 1 to 2mm
between ceiling and outer rim of
main body. Thickness of ceiling
shall be less than 25mm.
7. Test run and Installation of
grille
Switch power on and check
operation.
Remote control model –put
the plug of the remote control
power cord in the socket on IC
board in the grille (fig.4).
Illustration