Kruger KCE 300 M Series Instruction manual

General Instructions
IGB027.E1/2002
KCE 300-600 M Series
Maintenance
1.
2.
Ensure the fan is disconnected from the main power supply before any
service.
Do not use petrol oil or any other plastic-erosive oil for cleaning.
Caution
1. A double interruption jack must be installed at the wire inlet in order to isolate
power supply in case of emergency.
2. Do not install the fan at a place where water spray or excess steam exists.
3. Do not install the fan at a place with high humidity.
4. Check the voltage and frequency on the name plate against local power supply
5.
Installation height should be at least 2.5m above floor.
3. Remove the grille. with clean water.
5. Wipe the main body with cloth and neutral detergent.
maintenance and
4. Clean the grille using lukewarm water neutral detergent and rinse
6. Fit the grille back when it is dry.
the fan and
before usage.
Installation Instruction
1. Frame Installation
Use strengthened frame to
2. Connecting Pipe
Put the body into the fixing
Tighten the wood screw at the
mark (fig.2).
3. Main Body Installation
Insert the main body aligned
additional screws #10x25 (5
pcs).
support the whole weight of the
main body.
Woodframe use : 30 x 30 mm
frame, make a mark on it as per
the hole position shown in the
arrow and remove the body
(fig.1).
with connecting pipe.
temporally by wind screw.
Connect the pipe with main
Fix it
body tightly and fixed it by
4. Connecting & Exhaust pipe
Seal up the connecting place by
mixture.
Tilt down the exhaust pipe to
outdoor about 1° or 2°.
5. Electrical Distribution
Choose the corresponding wiring
purchased
A –normal model
B –remote control model
6. Ceiling Installation
Keep a space of 1 to 2mm
shall be less than 25mm.
7. Test run and Installation of
Switch power on and check
.
power cord in the socket on IC
board in the grille (fig.4).
adhesive tap or joint
diagram per your
model.
between ceiling and outer rim of
main body. Thickness of ceiling
grille
operation.
Remote control model –put
the plug of the remote control

Technical Specification
327/325 103/124 4 35/35 50/60 0.15/0.19 45/46 900/890 5
445/370 163/142 4 48/48 50 0.22/0.18 47/50 935/830
439/368 190/162 4 48/48 60 0.25/0.19 47/49 950/860
585/496 211/178 4 95/95 50 0.46/0.37 48/47 890/865
Installation
When installation, note the following precautions:-
Remove packing and ensure the appliance is not damaged.
Check that your electrical voltage and frequency correspond to those marked on the
rating label.
Do not start or operate the fan unless the protection grilles are in place.
Install the fan before building the ceiling; it shall be installed where it is durable to support the
the fan.
The adopted material for ceiling shall be strengthened and resonance-resistance
board, celotax board)
To prevent water from flowing back to the bathroom, tilt down the pipe to outdoor for 1° to 2°.
Select the exhaust-hole cover properly to avoid loud noise.
KCE series premium exhaust fan should be installed at a distance of at least 2.5m
Remove the interior grille from the fan casing and use self-driven screw to fix the
the ceiling frame. Fan casing and ceiling frame should be horizontal.
Install the interior grille and connect fan to the main power supply according to the
diagram.
Do not install it near gas
stove, above cooker or in
a place of high temp. over
40°C.
To improve the fan
efficiency in a closed
room, set up a convective
windows of 400 sq.cm in
opposite size to the fan.
Make sure to keep the
inspection port
Do not distribute the pipe according to the following ways or it will be wind, loud noise and
the counter flow board cannot be opened.
(1) Overbent
(2) Too many
bends on pipe
(3) Exhaust bend
pipe too close to
the main body.
(4) Connecting pipe
is shrunk
270 x 270
Illustration
weight of
(e.g. plaster
above floor.
fan casing to
wiring
KCE 300M
541/458 227/178 4 95/95 60 0.54/0.41 51/51 950/825
KCE 600M
KCE 400M
Description
KCE series premium exhaust fan is a new type low noise exhaust fan. All models
incorporate shaded pole motors with injection molded plastic structure. The KCE series
features premium performance, well-designed structure, esthetic appearance, fast
response, stable operation, large volume flow rate, low noise, low electricity consumption
and easy installation.
KCE series premium exhaust fan is mainly used to extract indoor foul air, smoke and dust.
It provides a healthy environment and helps to enhance the well-being of users. It is
suitable for bedroom, kitchen, bathroom, toilet, meeting room, commercial office and
shopping mall.
Correct installation is essential for the health and safety of people during operation of the
appliance. Therefore the regulations indicated in these instructions must be observed and
the mechanical protections must be prearranged.
If not properly installed the appliance may cause the risk of contact with the rotating fan,
with consequent collision and abrasion. In addition, if it is not wired correctly, it may
present risks related to electrical material. Should the appliance be required to operate in
isolation i.e in laboratory tests; it is necessary to block it appropriately and prearrange the
protections to avoid contact with the rotating parts. Room temperature must not exceed
55°c.
Transport
This appliance must not be overturn and the packing must not be deformed during transport.
If the gross weight indicated on the package is over 10 kg, the package must be carried manually
by more than one person. Appliance arranged on wooden-pallets must be moved with a transpallet.
Storage
The appliance should be stored in a dry place in their original packing. Appliances packed in cardboard
boxes may be stored on top of one another up to a maximum of 2 meters, when not otherwise indicated
on the package. Appliances on pallets which are placed in view cannot be stacked. After removing the
packing, check the integrity of the appliance. In case of doubt, do not use the appliance and contact us.
acking elements (plastic bags, foam rubber, nails, etc) must be kept out of the reach of children as they
P
are a potential source of danger.
6.5
9
320 x 320
385 x 385
Model Max. Q
m3/h
Max. Ps
Pa
N°
Poles
Power
W Hz Max Amp
dB (A)
at 3m RPM Wt kg
Installation
space
mm