Kustom Signals Eagle 3 User manual

S1
- Press to enter Menus. In Menus, pressing
increments Menu screens.
S2
- Initiates the display, internal and tuning fork
tests. In
Menus, pressing will save selection and
return
to Main Enforcement screen.
S3
- Programmable soft key short cut to favorite
menu.
Toggles Patrol Speed Blanking with a
locked target.
S4
- Control for power on / off.
Power off to save
current menu selections.
Eagle 3 Quick Reference Guide
North Carolina
1Eagle 3 Front Panel Controls
www.kustomsignals.com
Sales (800) 4KUSTOM [phone]
Customer Service [phone]
Eagle 3 Quick Reference Guide
KSI Part # 006-1003-11 Rev 1
4Eagle 3 Fork Test
Stationary Tuning Fork Test
1. Place the Eagle 3 in stationary mode, select Front antenna.
2. Press the Test button or touch screen lower right.
3. Lightly strike the low fork (30 mph) and place in front of the
antenna. Verify the speed displayed is ±1 mph.
4. Repeat for the high fork and rear antenna (if used.)
Moving Mode Tuning Fork Tests
1. Place in the Moving Opposite mode, select Front antenna.
2. Press the Test button or touch screen lower right.
3. Lightly strike the low fork (30 mph) and place in front of the
antenna. Verify the Patrol speed displayed is ±1 mph.
4. While holding the lower speed fork in front of the antenna,
lightly strike the high fork (55 mph) and place in front of the
antenna. Verify the Target speed displayed is the difference
between forks (25 mph) with a tolerance of ±1 mph.
5. Repeat for Same direction with the High, then Low forks.
6. Verify the speed is the sum of the forks (85) ±1 mph.
7. Repeat for the rear antenna (if used.)

2Eagle 3 Remote Control
A
Lock/Rel –
Toggles target Lock/Release. With
unit in HOLD, press and hold for QuikTrak. In
Audio Menu, toggles squelch on/off. In
Display Menu, toggles backlight control.
B
Move/STA - Toggles between stationary and
moving modes. In Display Menu, toggles C1 &
C3 display color settings.
C
Tgt Dir –Stationary –Press to select
Stationary All, approaching only, and
receding only. Moving - toggles between
Opposite and Same Direction. In C1 Display
Menu, progresses background colors.
D BACK - In Menus, press to go back 1 menu
E Access to battery compartment
F
LED –Red - trying to connect.
Green - connected
G
Front/Hold - Toggles on/off Front antenna. If
rear antenna active, press to place Rear
antenna in Hold and activate Front. In
Menus,
increases level.
H
Rear/Hold - Toggles on/off Rear antenna. If
front antenna active, press to place Front
antenna in Hold and activate Rear. In Menus,
decreases level.
I
Enter –In Menus, Enters selection and returns
unit to Main Enforcement screen.
J
Menu/BKLT - Quick press illuminates remote
backlight. Press and Hold to enter Menus. In
Menus, press to increment Menus.
A.
TGT DIR
In Stationary
operation, progresses All,
approaching only, and receding only target
zones. In Moving Operations, it toggles
Opposite
and Same
Direction. In C1 Display
menu, progresses background colors.
B.
Down Arrow
Down
arrow in menus; lowers brightness in
Display Menu with manual control.
C.
Front
Toggles Front antenna microwave
transmitter on/off
. Toggles C1/C3 color
selection
in Display Menu.
D. Rear
Toggles Rear antenna microwave
transmitter on/off
. Toggles C1/C3 color
selection
in Display Menu.
E.
Up Arrow
Toggles Moving/Stationary Modes, Up
arrow in menu
screens; increases
brightness in Display Menu with manual
control.
F.
Lock
Locks Target
Speed. Toggles
manual/automatic brightness control in
Display Menu.
G. Test
Short cut to Tuning Fork test.
3Eagle 3 Touch Screen Control Pads
NOTE: The first
button press wakes
the remote. It will
take action on the
next button press.
NOTE: NO LED
indicates the
batteries need to be
replaced.