KYLAND Technology SICOM3028GPT Series Assembly instructions

SICOM3028GPT Series Industrial Ethernet
Switches Hardware Installation Manual
Publication Data: Sep. 2016
Version: V1.3

SICOM3028GPT Series Industrial Ethernet Switches
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content of this manual as
accurate and as updated as possible. This document is not guaranteed to be error-free, and
we reserve the right to amend it without notice to users.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or
duplicated, in any form or by any means without the prior written permission of KYLAND
Corporation.
Copyright © 2016 Kyland Technology Co., Ltd.

Notice for Safety Operation
The product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the device should be avoided. Before using the device, read this
manual carefully for personal and equipment safety. Please keep the manual for further
reference. Kyland is not liable to any personal or equipment damage caused by violation of
this notice.
Do not place the device near water sources or damp areas. Keep the ambient relative
humidity within the range from 5% to 95% (non-condensing).
Do not place the device in an environment with high magnetic field, strong shock, or high
temperature. Keep the working and storage temperatures within the allowed range.
Install and place the device securely and firmly.
Please keep the device clean; if necessary, wipe it with a soft cotton cloth.
Do not place any irrelevant materials on the device or cables. Ensure adequate heat
dissipation and tidy cable layout without knots.
Wear antistatic gloves or take other protective measures when operating the device.
Avoid any exposed metal wires because they may be oxidized or electrified.
Install the device in accordance with related national and local regulations.
Before power-on, make sure the power supply is within the allowed range of the device.
High voltage may damage the device.
Power connectors and other connectors should be firmly interconnected.
Do not plug in or out the power supply with wet hands. When the device is powered on,
do not touch the device or any parts with wet hands.
Before operating a device connected to a power cable, remove all jewelry (such as rings,
bracelets, watches, and necklaces) or any other metal objects, because they may cause
electric shock or burns.
Do not operate the device or connect or disconnect cables during an electrical storm.
Use compatible connectors and cables. If you are not sure, contact our sales or
technical support personnel for confirmation.

Do not disassemble the device by yourself. When an anomaly occurs, contact our sales
or technical support personnel.
If any part is lost, contact our sales or technical support personnel to purchase the
substitute. Do not purchase parts from other channels.
Dispose of the device in accordance with relevant national provisions, preventing
environmental pollution.
Specification of the internal fuses in this equipment: 3.15A/300V.
In the following cases, please immediately shut down your power supply and contact your
Kyland representative:
Water gets into the equipment.
Equipment damage or shell damage.
Equipment operation or performance has abnormally changed.
The equipment emits odor, smoke or abnormal noise.
The following information applies when operating this device in hazardous locations:
Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous Locations, or
nonhazardous locations only.
Cet appareillage est utilisable dans les emplacements de Classe I, Division 2, Groupes A, B,
C et D, ou dans les emplacements non dangereux seulement.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment while the circuit is live or unless the area is known to be
free of ignitable concentrations.
Substitution of any component may impair suitability for Class I, Division 2.
AVERTISSEMENT: RISQUE D'EXPLOSION
Avant de deconnecter l'equipement, couper le courant ou s'assurer que l'emplacement
est designe non dangereux.
La substitution de composants peut rendre ce materiel inacceptable pour les
emplacements de Classe I, Division 2.

I
Contents
1 Product Overview...............................................................................................................1
2 Structure and Interface.......................................................................................................5
2.1 Front Panel ..................................................................................................................5
2.2 Rear Panel...................................................................................................................6
2.2.1 1U Interface Module..............................................................................................6
2.2.2 0.5U Interface Module ...........................................................................................7
3 Interface Module Installation...............................................................................................8
3.1 Mounting Modes and Steps .........................................................................................8
3.1.1 Installing Mounting Brackets..................................................................................9
3.1.2 Inserting a 0.5U Interface Module into an Upper Slot (Slot 2, Slot 4, or Slot 6).....9
3.1.3 Inserting a 0.5U Interface Module into a Lower Slot (Slot 3, Slot 5, or Slot 7).....10
3.1.4 Inserting a 1U Interface Module into Slot 1..........................................................12
3.2 Dismounting...............................................................................................................12
3.2.1 Removing a 0.5U Interface Module.....................................................................12
3.2.2 Removing a 1U Interface Module........................................................................12
4 Switch Installation.............................................................................................................14
4.1 Dimension Drawing....................................................................................................14
4.2 Mounting Modes and Steps .......................................................................................15
5 Connection .......................................................................................................................18
5.1 10/100Base-T(X) Ethernet Port..................................................................................18
5.2 100Base-FX Ethernet Port.........................................................................................19
5.3 10/100/1000Base-T(X) Ethernet Port.........................................................................20
5.4 1000Base-X, 10/100/1000Base-T(X) SFP slot...........................................................21
5.4.1 Gigabit SFP Optical Module ................................................................................22
5.4.2 Gigabit SFP Electrical Module.............................................................................23
5.5 Console Port ..............................................................................................................23
5.6 Grounding..................................................................................................................25

II
5.7 Power Terminal Block................................................................................................26
5.8 Alarm Terminal Block.................................................................................................28
6 LEDs.................................................................................................................................30
7 Switch Access ..................................................................................................................33
7.1 Access through Console Port.....................................................................................33
7.2 Access through Telnet ...............................................................................................35
7.3 Access through Web..................................................................................................36
8 Basic Features and Specifications....................................................................................37

Product Overview
1
1 Product Overview
The series switches include layer-2 switches and layer-3 switches. With modular design, all
these switches support IRIG-B, GPS, serial port, HSR, and many other modules for easy
expansion.
Based on the full gigabit switching platform, the series switches are the first industrial
Ethernet switches that employ the IEC61850 modeling technology in the world, achieving
unified management. The switches support IEC62439-6 and IEC62439-3 ring redundancy
protocol and comply with the IEC61850-3 and IEEE1613 power industry standards. With
industry-leading clock frequency synthesis technology, the switches support IEEE1588-2008
Precision Time Protocol (PTP), as listed in Table 1. All these features enable the switches to
well suit the Smart Grid industry.
The series switches support 19 inch 1U rack mounting by front/rear panel. They provide two
console ports on the front panel and one 1U and six 0.5U slots for interface modules on the
rear panel.
Table 1 Models
Model
SICOM3028GPT-L2GT-MB-PS1-PS2, SICOM3028GPT-L2FT-MB-PS1-PS2,
SICOM3028GPT-L2G-MB-PS1-PS2, SICOM3028GPT-L2F-MB-PS1-PS2,
SICOM3028GPT-L3GT-MB-PS1-PS2, SICOM3028GPT-L3FT-MB-PS1-PS2,
SICOM3028GPT-L3G-MB-PS1-PS2, SICOM3028GPT-L3F-MB-PS1-PS2
Code definition
Code option
L2GT-MB
Layer 2 1000M IEEE1588-compliant host
L2FT-MB
Layer 2 100M IEEE1588-compliant host
L2G-MB
Layer 2 1000M IEEE1588 non-compliant host
L2F-MB
Layer 2 100M IEEE1588 non-compliant host
L3GT-MB
Layer 3 1000M IEEE1588-compliant host
L3FT-MB
Layer 3 100M IEEE1588-compliant host
L3G-MB
Layer 3 1000M IEEE1588 non-compliant host

Product Overview
2
L3F-MB
Layer 3 100M IEEE1588 non-compliant host
PS1: power input 1
HV(220AC/DCW), L1(48DC), L3(24DC)
PS2: power input 2
HV(220AC/DCW), L1(48DC), L3(24DC), N/A
Table 2 Interface Modules (1U)
Model
SM6.6-Ports-1U
Code definition
Code option
Ports: GX/GE
4GX, 4GE, 2GX2GE
Note:
2GX2GE: two 1000Base-X, 10/100/1000Base-T(X) SFP slots; two
10/100/1000Base-T(X) ports
Table 3 Interface Modules (0.5U)
Model
SM6.6-Ports-Connector-0.5U
Code definition
Code option
Ports: GX/GE, S/M, T
SICOM3028GPT-L2GT-MB, SICOM3028GPT-L2G-MB,
SICOM3028GPT-L3GT-MB, SICOM3028GPT-L3G-MB:
4GE, 4GX, 2GX2GE, 2GX2S, 2GX2M
All SICOM3028GPT models:
4S, 4M, 2S2T, 2M2T, 4T
Note:
2GX2GE: two 1000Base-X, 10/100/1000Base-T(X) SFP slots; two
10/100/1000Base-T(X) ports
2S2T: two 100Base-FX ports, single mode; two 10/100Base-T(X) ports
2M2T: two 100Base-FX ports, multiple mode; two 10/100Base-T(X) ports
Connector: parameters for
S/M
Ports with M:
SC05=SC connector, 1310nm, 5km
ST05=ST connector, 1310nm, 5km

Product Overview
3
FC05=FC connector, 1310nm, 5km
Ports with S:
SC40=SC connector, 1310nm, 40km
ST40=ST connector, 1310nm, 40km
FC40=FC connector, 1310nm, 40km
SC60=SC connector, 1310nm, 60km
SC80=SC connector, 1550nm, 80km
Ports without S or M:
N/A
Table 4 Other Modules
Model
Description
Applicable to
SM6.6-GPS-OI-0.5U
GPS-to-PTP clock synchronization module,
supports one GPS input, and one PPS output
SICOM3028GPT-L2GT-MB,
SICOM3028GPT-L2FT-MB,
SICOM3028GPT-L3GT-MB,
SICOM3028GPT-L3FT-MB
SM6.6-GPS-OI-FI-0.5U
GPS-to-PTP clock synchronization module,
supports one GPS input, one 5M/10M
frequency input, and one PPS output
SM6.6-PTP-BO-0.5U
PTP-to-IRIG-B clock conversion module,
supports two IRIG-B (DC) outputs, two IRIG-B
(AC) outputs, one PPS output
SM6.6-PTP-over-E1-0.5U
PTP over E1 clock synchronization module,
supports E1 interface with balanced connection
SM6.6-4D-232/422/485-0
.5U
Serial port module without RTS Carrier Control,
supports four RS232/RS422/RS485 serial ports
All SICOM3028GPT models
SM6.6-4D-A-4RS232/422
/485-0.5U
Serial port module with RTS Carrier Control,
supports four RS232/RS422/RS485 serial ports
SM6.6-HSR/PRP-GX-0.5
U
HSR/PRP Redbox module, supports two
1000Base-X, 10/100/1000Base-T(X) SFP slots
SICOM3028GPT-L2GT-MB,
SICOM3028GPT-L2G-MB,

Product Overview
4
SM6.6-HSR/PRP-GE-0.5
U
HSR/PRP Redbox module, supports two
10/100/1000Base-T(X) ports
SICOM3028GPT-L3GT-MB,
SICOM3028GPT-L3G-MB
SM6.6-MFA-0.5U
Multi functional application module, supports
one 1000Base-X, 10/100/1000Base-T(X)
Combo port
Note：
For the product information listed in these tables, we reserve the right to amend it without notice.
To obtain the latest information, you can contact our sales or technical support personnel.

Structure and Interface
5
2 Structure and Interface
Caution:
It is recommended to purchase the port dustproof shield (optional) to keep ports clean and
ensure device performance.
2.1 Front Panel
Figure 1 Front Panel
Table 5 Description of the Front Panel
No.
Identifier
Description
(1)
Alarm
Alarm LED
(2)
Run
Running LED
(3)
Ring
Ring LED
(4)
Lock
Synchronization Finish LED
(5)
PWR2
Power 2 LED
(6)
PWR1
Power 1 LED
(7)
Slot (1-7) Speed (1-4)
Four port speed LEDs (for interface module slots 1 to 7)
(8)
Slot (1-7) Link/ACT (1-4)
Four port connection status LEDs (for interface module slots 1
to 7)
(9)
Console
Two console ports

Structure and Interface
6
2.2 Rear Panel
Figure 2 Rear Panel
2.2.1 1U Interface Module
SM6.6-4GX-1U
1-4: four 1000Base-X, 10/100/1000Base-T(X) SFP slots
SM6.6-2GX2GE-1U
1-2: two 10/100/1000Base-T(X) Ethernet ports
3-4: two 1000Base-X, 10/100/1000Base-T(X) SFP slots
SM6.6-4GE-1U
1-4: four 10/100/1000Base-T(X) Ethernet ports

Structure and Interface
7
2.2.2 0.5U Interface Module
SM6.6-4GX-0.5U
1-4: four 1000Base-X, 10/100/1000Base-T(X) SFP slots
SM6.6-2GX2M-SC05-0.5U, SM6.6-2GX2S-SC40-0.5U
1-2: two 100Base-FX Ethernet ports (FC/ST/SC connector)
3-4: two 1000Base-X, 10/100/1000Base-T(X) SFP slots
SM6.6-4GE-0.5U
1-4: four 10/100/1000Base-T(X) Ethernet ports
(Note: Its appearance is identical with that of SM6.6-4T-0.5U. You can distinguish them by
labels on the front panel.)
SM6.6-2GX2GE-0.5U
1-2: two 10/100/1000Base-T(X) Ethernet ports
3-4: two 1000Base-X, 10/100/1000Base-T(X) SFP slots
SM6.6-4M-SC05-0.5U, SM6.6-4S-SC40-0.5U
1-4: four 100Base-FX Ethernet ports (FC/ST/SC connector)

Interface Module Installation
8
SM6.6-2M2T-SC05-0.5U, SM6.6-2S2T-SC40-0.5U
1-2: two 10/100Base-T(X) Ethernet ports
3-4: two 100Base-FX Ethernet ports (FC/ST/SC connector)
SM6.6-4T-0.5U
1-4: four 10/100Base-T(X) Ethernet ports
(Note: Its appearance is identical with that of SM6.6-4GE-0.5U. You can distinguish them
by labels on the front panel.)
SM6.6-GPS-OI-0.5U
For details, refer to the GPS Clock Synchronization Module Hardware Installation Manual.
SM6.6-PTP-BO-0.5U
For details, refer to the IRIG-B Clock Conversion Module Hardware Installation Manual.
SM6.6-4D-232/422/485-0.5U, SM6.6-4D-A-4RS232/422/485-0.5U
For details, refer to the Serial Device Server Module Hardware Installation Manual.
SM6.6-HSR/PRP-GX-0.5U, SM6.6-HSR/PRP-GE-0.5U
For details, refer to the HSP/PRP Redbox Module Hardware Installation Manual.
3 Interface Module Installation
Caution:
Power off the switch before you install or remove an interface module.
3.1 Mounting Modes and Steps
The series switches provide one 1U slot (Slot 1) and six 0.5U slots (Slot 2-Slot 7) on the rear
panel, as shown in Figure 2. You can install interface modules as needed. Table 2- Table 4

Interface Module Installation
9
list the models of the interface modules.
Note：
Not all the slots require interface modules. Choose slots as needed.
3.1.1 Installing Mounting Brackets
Before inserting a 0.5U interface module into an upper or lower slot, install mounting
brackets on the module as follows:
Select an applicable 0.5U interface module. Insert two mounting brackets into the screw
holes at both sides of the module. Push the brackets in direction 1 until the brackets are
firmly secured to the module.
Figure 3 Installing Mounting Brackets
3.1.2 Inserting a 0.5U Interface Module into an Upper Slot (Slot 2, Slot 4, or Slot 6)
Step 1: Insert the guide rail of the interface module into the guide rail slot with "TOP" facing
up. Then push the module into the slot along the guide rail slot until it is in position.

Interface Module Installation
10
Figure 4 Inserting a 0.5U Interface Module into an Upper Slot
Caution:
To insert an interface module into an upper slot, keep the "TOP" identifier on the module
facing up.
If the module cannot be pushed into place, do not force it, because too much force may cause
damage to the module. In this case, remove the module and check the guide rail slot for any
foreign materials or deformation. If the fault cannot be rectified, contact our sales or technical
support personnel
Step 2: Push the mounting brackets into the slot completely. Insert two captive screws
(M2.5×6) into the screw holes of the switch to secure the interface module to the
switch.
3.1.3 Inserting a 0.5U Interface Module into a Lower Slot (Slot 3, Slot 5, or Slot 7)
Step 1: Insert the guide rail of the interface module into the guide rail slot with "TOP" facing

Interface Module Installation
11
down. Then push the module into the slot along the guide rail slot until it is in
position.
Figure 5 Inserting a 0.5U Interface Module into a Lower Slot
Caution:
To insert an interface module into a lower slot, keep the "TOP" identifier on the module facing
down.
If the module cannot be pushed into place, do not force it, because too much force may cause
damage to the module. In this case, remove the module and check the guide rail slot for any
foreign materials or deformation. If the fault cannot be rectified, contact our sales or technical
support personnel.
Step 2: Push the mounting brackets into the slot completely. Insert two captive screws
(M2.5×6) into the screw holes of the switch to secure the interface module to the
switch.

Interface Module Installation
12
3.1.4 Inserting a 1U Interface Module into Slot 1
The steps for inserting a 1U interface module into Slot 1 is the same as those for inserting a
0.5U interface module into an upper slot (Slot 2, Slot 4, or Slot 6). For details, see section
3.1.2.
3.2 Dismounting
3.2.1 Removing a 0.5U Interface Module
The steps for removing an interface module from an upper slot and a lower slot are the same.
Detailed steps are as follows:
Step 1: Remove the two screws securing the module to the switch.
Step 2: Pull out the mounting brackets.
Step 3: Remove the module from the switch by holding the brackets.
Step 4: Remove the brackets from the module, as shown in the following figure.
Figure 6 Removing Mounting Brackets
3.2.2 Removing a 1U Interface Module
Step 1: Remove the three screws (M2.5×6) securing the module to the switch.
Step 2: Pull out the module by holding the handle until the module is completely detached
from the slot.

Interface Module Installation
13
Figure 7 Removing a 1U Interface Module

Switch Installation
14
4 Switch Installation
4.1 Dimension Drawing
Figure 8 Dimensions (unit: mm)
Caution:
As part of the heat dissipation system, the switch housing becomes hot during operation.
Please use caution when coming in contact and avoid covering the switch housing when the
switch is running.
The figures in this manual are only for reference.