Labnet FastPette Pro User manual

This quick guide is intended to provide a brief overview
of the main features and operation of Labnet pipet
controllers. For detailed information, please refer to the
User Manual that can be found at www.labnetlink.com
in several languages.
Labnet FastPette™
Pro and V2
Quick Start Guide
Catalog Numbers:
P2002 (FastPette Pro)
P2000 (FastPette V2)

Intended Use
The pipet controller is a device
intended for general laboratory
use only, for pipetting liquids with
the use of measuring pipets. It
can work with all types of glass or
plastic pipets in the volume range
from 0.5 mL to 100 mL.
Battery Charge
The batteries may be charged only
with the original charger. Using
chargers other than the original
one may damage the battery.
Fastepette™ Pro: 3 NiHM type AAA
are delivered with the product and
need to be installed before the
rst use.
FastPette V2: NiHM battery is
installed in the product.
Use country specic adapter.
Charge the batteries either
on charging stand or directly
connecting the charger to the
socket. Input: 100-240V, 50/60Hz,
0.2A; output: DC 9V.
Charging process is indicated by:
FastPette Pro: successive lighting
of “bars”. Full charging time: 7 to
8 hours. The batteries are charged
when all 3 “bars” are displayed
simultaneously.
FastPette V2: continuous lighting
of the LED indicator, which stops
after the charger is disconnected.
Full charging time: up to 11 hours.
0.5 mL to
100 mL
EU US
UK AU
TOP TOP
TOP
TOP
O
P
E
N
OR
FastPette
Pro only
FastPette
Pro only

Speed Setting
FastPette™ Pro: Press the SPEED
button until the display shows
the correct speed – HIGH or LOW.
FastPette V2: Change position of
the SPEED switches.
• HIGH speed - fast aspirating
recommended for pipets <5 mL
• LOW speed - slow aspirating
recommended for pipets >5 mL
and foaming liquids
Manual Speed Control
• Speed can be controlled
manually by pressing the
trigger buttons
Mode Control
FastPette Pro: Press the MODE
button until the display shows
the correct mode – BLOW OUT
(arrow) or GRAV (drop).
FastPette V2: Change position of
the MODE switches.
NOTE: Pump is not working when
in GRAV mode.
Filter Replacement
OR
OR

Safety Notes
WARNING! Risk of injury
CAUTION: Risk of damage to the device or errors in
pipetting of liquids.
Before starting the work with the pipet controller every
user should read these operating instructions carefully.
CAUTION:
• Using the device inconsistently with the operating
instructions may result in damaging the device.
• The device should be serviced only at an authorized
service center, otherwise the manufacturer will be
relieved from any liability under the warranty.
• Only original spare parts and accessories, recommended
by the manufacturer, shall be used.
• Only the original charger, supplied by the manufacturer,
shall be used for charging the batteries.
• In case of incorrect functioning of the pipet controller,
work shall be stopped. The device shall be cleaned and
sent for repair to an authorized service center.
• In the case of mechanical damage to the casing, the
device shall be immediately sent for repair to an
authorized service center.
• The use of excessive force during work shall be avoided.
WARNING!
• During the work with the pipet controller general safety
regulations regarding risks related with laboratory work
should be observed. Protective clothing, goggles, and
gloves should be worn.
• The pipet controller shall not be used for measuring
substances with vapors of which damage the following
plastics: PP, SI, EPDM, POM.
• The pipet controller shall not be used in an environment
where explosion risk is present.
• Flammable liquids shall not be measured – in particular
substances with ash-point below 0°C (ether, acetone).
• The pipet controller shall not be used for drawing acids
with a concentration above 1 mol/L.
• The pipet controller shall not be used for drawing
solutions with a temperature above 50°C.
• The pipet controller may work in temperature range
from +10°C to +35°C.
• In the case of mechanical damage to the casing, the
device shall be immediately sent for repair to an
authorized service center.

Cleaning
• External parts may be cleaned with a swab moistened
with isopropyl alcohol.
• The nose piece and the pipet holder may be autoclaved
at 121°C for 20 minutes.
• The lter included in the set may be sterilized by
autoclaving at 121°C for not more than 15 minutes.
• The outer body of the pipet controller is UV resistant,
the recommended distance from the radiation source
to exposed element should be not less than 50 cm.
Prolonged and very intense UV exposure can cause
de-coloration of pipet controller parts, without affecting
its performance.
Product Disposal
According to Directive 2012/19/EU of the
European Parliament and of the Council of
4 July 2012 on waste electrical and electronic
equipment (WEEE), the HTL Swiftpet Pro Pipet
Controller is marked with the crossed-out
wheeled bin and must not be disposed of
with domestic waste.
Consequently, the buyer shall follow the
instructions for reuse and recycling of waste
electronic and electrical equipment (WEEE)
provided with the products and available at
www.corning.com/weee.
Warranty
The Labnet FastPette™ Pro and FastPette V2 pipet
controllers are covered by a 1 (one) year limited warranty.
For more information on the warranty limitations refer
to full version of the User Manual available at
www.labnetlink.com.

© 2021 Corning Incorporated. All rights reserved.
7/21 CLSLN-AN-1008DOC REV1
Made in Poland
For a listing of trademarks, visit www.corning.com/clstrademarks.
All other trademarks are the property of their respective owners.
For additional product or technical information, visit
www.labnetlink.com or contact your local sales ofce.
NORTH AMERICA
t 800.492.1110
t 978.442.2200
ASIA/PACIFIC
Australia/New Zealand
t 61 427286832
Chinese Mainland
t 86 21 3338 4338
f 86 21 3338 4300
India
t 91 124 4604000
f 91 124 4604099
Japan
t 81 3-3586 1996
f 81 3-3586 1291
Korea
t 82 2-796-9500
f 82 2-796-9300
Singapore
t 65 6572-9740
f 65 6735-2913
Taiwan
t 886 2-2716-0338
f 886 2-2516-7500
EUROPE
[email protected]
France
t 0800 916 882
Germany
t 0800 101 1153
The Netherlands
t 020 655 79 28
United Kingdom
t 0800 376 8660
All Other European
Countries
t [phone]
LATIN AMERICA
[email protected]
Brazil
t 55 (11) 3089-7400
Mexico
t (52-81) 8158-8400