Labnet Orbit S2030-LS-B-230 User manual

Lit M00707 Rev.3, August 2016
Orbit LS Low Speed Orbital Shaker
User Manual
S2030-LS-B
S2030-LS-B-230
DOMINIQUE DUTSCHER SAS

DOMINIQUE DUTSCHER SAS

1.0 GENERAL SPECIFICATIONS
Electrical requirements:
115V model 115V ± 10% - 50/60Hz, 0.3A
230V model 230V ± 10% - 50/60Hz, 0.15A
Fuse 2 x 0.5A 230V ; 2 x 1A 115V
Speed from 3 to 60 rpm
Shaker Orbit 19 mm (3/4 inch)
Timer 20 – 120 min in 10 min step, HOLD function
Maximum Load 5 kg
Dimensions WxLxH 295x340x160mm
Platform dimensions WxL 295x295mm useable area
Weight 6.6 kg
Operating Conditions 4°C to 70°C, up to 85% RH, non-condensing
2.0 INSTALLATION OF THE SHAKER
2.1 UNPACKING
Before starting the installation, carefully examine the shaker for possible damage or
missing parts.
- Open the box and carefully remove the padding. Check that the shaker has
not been visibly damaged during transportation. Keep the packing material
until you are sure that the shaker works properly.
- Carefuly lift the device out of the box.
- Be sure that the following information is included on the serial label located
on the back of the unit: Serial Number, Product number, Electrical rating.
- Check that the power cord has a pin configuration that fits into a wall socket
according to the local standard.
Should any kind of damage have occurred during transportation, contact the carrier
immediately. The carrier is responsible for shipping damage.
2.2 SELECTING THE CORRECT LOCATION
When locating the shaker, please consider following:
- Put the shaker on horizontal, leveled and stable surface.
- Leave enough space around the shaker for normal air circulation, min. 10 cm.
- Leave enough space around the shaker for easy access and maintenance.
- Avoid locations subject to shocks and vibrations.
- Avoid locations subject to frequent power fluctuations or power losses (It may
affect shaker performance)
Note: There has to be an easy access to the shaker control panel and main plug in case of
emergency
2.3 ATTACHING THE POWER CORD
First connect the main power cord to the shaker then connect the plug end of the cord to a
grounded wall socket. Avoid lines on which powerful electric motors, refrigerators and
similar devices are connected.
Be careful when you plug the cord to a grounded wall socket!
Do not touch plug with wet hand!
DOMINIQUE DUTSCHER SAS

Do not pull the plug by the cord!
3.0 INSTRUCTIONS FOR USE
1. POWER switch – to turn the shaker ON (power switch illuminates) or OFF
2. SPEED potentiometer – to set the shaker speed
3. TIME potentiometer – to set timed operation
4. HOLD – yellow light illuminates when shaker is set on HOLD for
continuous operation
5. START/STOP button to start or stop shaking
6. RUN – green light illuminates when shaker operates
Note: The speed can be adjusted at any time during shaker operation. The time
however can not be changed while the shaker is in motion. To change the time
press the STOP button first, allow the shaker platform to come to full stop and set
the time value again. Restart the shaker.
Do not use the shaker near water sources. Be sure that water doesn’t
get on the device, especially during the cleaning procedures.
•Do not expose the shaker to the aggressive vapors (e.g. organic solvents).
•Do not insert any objects into the shaker (such as screw driver or metal rods).
•Never operate the shaker without platform securely attached.
•Hazardous samples should be shaken only in appropriate containment vessels.
NOTE :
Misuse or unauthorized modifications will waive the warranty rights. If the equipment
is used in a manner not specified by the manufacturer, the safety features of the
shaker may be impaired.
Do not shake flammable or explosive samples!
START
STOP
HOLD
RUN
POWER
10
30
150
120
50
100
70
90
10
20
30
40
120
110
100
80
50
60
70
90
SPEED
(RPM)
TIME
(MIN)
1 2 3 4 5
6
DOMINIQUE DUTSCHER SAS

4.0. TROUBLESHOOTING GUIDE / SERVICE
Should you have a question about the operation of the Orbit Low Speed Shaker or if
service is required, contact Corning at: 800-492-1110. Do not send in a unit for service
without first calling to obtain a repair authorization number. Should the unit require return
to Corning for service, it should be properly packed to avoid damage. Any damage
resulting from improper packaging shall be the responsibility of the user.
Problem Explanation / Solution
POWER key doesn’t light up Check the power connection, Check fuses
Call Labnet Service Department
Shaker does not START Check the power connection, Check fuses
Call Labnet Service Department
5.0. ROUTINE MAINTANCE / CLEANING
•No routine maintenance or lubrication is required.
•It is recommended that the shaker is kept clean to warrant long trouble-free
operation.
5.1. CLEANING
The outside housing can be cleaned with soft, damp cloth when needed.
Do not use any aggressive or abrasive cleaners (acetone, nitro, polish etc.) This may
permanently damage the shaker finish.
Before cleaning the shaker, always unplug the power cord from the wall
socket!
DOMINIQUE DUTSCHER SAS

EQUIPMENT DISPOSAL-EUROPEAN REGULATIONS
According to Directive 2012/19/EU of the European Parliament
and of the Council of 4 July 2012 on waste electrical and
electronic equipment (WEEE), Orbit Low Speed Shaker is
marked with the crossed-out wheeled bin and must not be
disposed of with domestic waste.
Consequently, the buyer shall follow the instructions for reuse
and recycling of waste electronic and electrical equipment
(WEEE) provided with the products and available at the
following link: www.corning.com/weee
DOMINIQUE DUTSCHER SAS

Warranty Statement
Corning Incorporated (Corning) warrants that this product will be free from defects in material and
workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL
OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.
Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof that
proves defective in material or workmanship within the warranty period, provided the purchaser
notifies Corning of any such defect. Corning is not liable for any incidental or consequential
damages, commercial loss or any other damages from the use of this product.
This warranty is valid only if the product is used for its intended purpose and within the guidelines
specified in the supplied instruction manual. This warranty does not cover damage caused by
accident, neglect, misuse, improper service, natural forces or other causes not arising from defects
in original material or workmanship. This warranty does not cover motor brushes, fuses, light bulbs,
batteries or damage to paint or finish. Claims for transit damage should be filed with the
transportation carrier.
In the event this product fails within the specified period of time because of a defect in material or -
workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-1110;
Canada: 1-978-442-2200. For other regions of the world, please visit www.corning.com/lifesciences
or see the included instruction manual for a list of World Wide Support Offices.
Corning’s Customer Service team will help arrange local service where available or coordinate a
return authorization number and shipping instructions. Products received without proper
authorization will be returned. All items returned for service should be sent postage prepaid in the
original packaging or other suitable carton, padded to avoid damage. Corning will not be
responsible for damage incurred by improper packaging. Corning may elect for onsite service for
larger equipment.
Some states do not allow limitation on the length of implied warranties or the exclusion or limitation
of incidental or consequential damages. This warranty gives you specific legal rights. You may
have other rights which vary from state to state.
No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the
period of this warranty.
For your reference, make a note of the serial number, date of purchase and supplier here.
Serial No. ____________________ Date Purchased _________________
Supplier _____________________________________________________
Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended for use in diagnostic or
therapeutic procedures. Corning makes no claims regarding the performance of these products for clinical or diagnostic
applications.
Please register your product online at:
www.labnetinternational.com
DOMINIQUE DUTSCHER SAS

[e-mail]
www.labnetinternational.com
LN149000
DOMINIQUE DUTSCHER SAS