Labnet C1301 User manual

Spectrafuge Mini Centrifuge
User Manual
C1301
C1301-230V

About This Manual
This manual is designed to assist you in the optimal usage of your Spectrafuge Mini
Centrifuge. The manual is available in English, French, German, Italian, Portuguese,
and Spanish on our website at www.labnetinternational.com

General Information:
The Spectrafuge Mini Centrifuge is supplied with two rotors, one for microtubes and one
for 0.2ml PCR strip tubes. The 6 x 1.5ml rotor is designed to centrifuge up to six
individual 1.5ml plastic microcentrifuge tubes. It will also accept 0.5ml and 0.4ml tubes
with the adapters supplied with the unit. Adapters are available separately for 0.2ml
tubes. The strip tube rotor is designed to centrifuge two 8 x 0.2ml strip tubes. It will also
accept up to 16 individual 0.2ml tubes. Both rotors are designed for applications
requiring relatively low g-forces, such as microfiltration, cell separation and quick spin
downs from the walls of tubes. Please read this manual thoroughly before attempting to
operate the centrifuge.
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
Warranty:
The centrifuge and rotor are covered by a one year warranty. This warranty covers the
centrifuge and rotor. This warranty is void in the event of incorrect operation, use of
nonstandard spare parts or accessories and unauthorized modification of the rotor or
centrifuge. The rotor warranty does not cover normal wear and tear or damage and/or
weakening caused by radioactive contamination, cleaning agents, or over tightening of
the allen screw. Fuses are not covered by the warranty.
Exchanging Rotors:
The centrifuge is supplied with two interchangeable rotors. The rotors are easily
exchanged using the allen wrench provided. Locate the set screw on the rotor shaft
below the rotor head. Using the wrench, loosen the set screw and pull up on the rotor to
remove. Place the other rotor into position on the motor shaft. Take care not to press the
rotor down so far as to compress the rubber collar at the base of the shaft. Tighten the
screw using the allen wrench until finger tight. Do not over tighten as this will cause
damage to the rotor and the motor shaft.
Installation:
Place the centrifuge on a level, clean surface, position the centrifuge near an accessible
power outlet so that the cord and outlet are within easy reach of the operator.
Operation:
Before operating the centrifuge, be sure that the power switch is in the “on” position. To
begin a run, simply close the lid of the centrifuge. No other controls are required. To stop
rotation, press down on the lid release tab on the front of the unit. This will release the lid
lock and the rotor will slow gradually to a complete stop. Caution: Do not attempt to open
the lid or remove samples until the unit has come to a complete stop. After the rotor has
stopped, the lid may be opened by grabbing it with the thumb on the front and fingers on
the back then lifting the lid back on the hinge. Safe operation of the centrifuge requires
that the rotor be loaded in a balanced fashion. Failure to load the rotor properly presents
a hazardous condition and may damage the centrifuge. Individual tubes, strip tubes

and/or adapters must always be loaded symmetrically to ensure proper balance. Never
run the centrifuge with only one strip tube in place.
Safety Precautions:
NEVER use the centrifuge in any manner not specified in these instructions.
NEVER put hands in the rotor area unless the rotor is completely stopped.
NEVER move the centrifuge while the rotor is spinning.
NEVER use solvents or flammables near this or other electrical equipment.
NEVER centrifuge flammable, explosive or corrosive materials
NEVER centrifuge hazardous materials outside of a hood or proper containment
facility
NEVER continue to operate a centrifuge that is vibrating excessively.
ALWAYS load the rotor symmetrically. Each plate should be counterbalanced by
another plate of the same brand, type and volume.
ALWAYS use plates that have been sealed in some manner to avoid spillage.
ALWAYS load plates so that the sealed side faces the center of the rotor and the
bottom of the plate faces out.
ALWAYS be sure the plates are pushed all the way to the bottom of the rotor slot
before operating the centrifuge.
ALWAYS locate the centrifuge within easy access to an electrical outlet.
Cleaning:
Before using any cleaning or decontamination methods except those recommended by
the manufacturer, check with the manufacturer that the proposed method will not
damage the equipment. To clean the centrifuge, use a damp cloth and a mild,
noncorrosive detergent (ph <8). After cleaning, ensure all parts are dried thoroughly
before attempting to operate the unit. Do not immerse the centrifuge in liquid or pour
liquids over it.
Questions and Service:
Should you have a question about the operation of the Spectrafuge Mini Centrifuge or if
service is required, contact Corning at: 800-492-1110. Do not send in a unit for service
without first calling to obtain a repair authorization number. Should the unit require
return to Corning for service, it should be properly packed to avoid damage. Any
damage resultingfrom improper packaging shall be the responsibility of the user.
Specifications:
Dimensions... ........ 6” x 6” (153 x 153mm)

Electrical ............... 115V, 50/60Hz,130mA
Fuse ..................... 0.5A, 250V (F)
Speed ................... 6000rpm
RCF ...................... 2000 x g Ambient Operating Range: 0 to 40°C,< 85%
Spare Parts:
Replacement 1.5ml rotor: C-1300-RT
Replacement strip rotor: C-1300-RTS
Replacement allen key: C-1300-RW
Replacement fuses: ME973
Appendix
Symbols and Conventions
The following chart is an illustrated glossary of the symbols that may be used in this
manual or on the product.
The electrical warning indicates the presence of a potential hazard which
could result in electrical shock.
CAUTION This symbol refers you to important operating and maintenance
(servicing) instructions within the product Instruction Manual. Failure to
heed this information may present a risk of damage or injury to persons or
equipment.
This symbol identifies a Protective Earth (PE) terminal, which is provided for
connection of the supply system’s protective earth (green or green/yellow)
conductor.
Equipment Disposal—European Regulations
According to Directive 2012/19/EU of the European Parliament and of the
Council of 4 July 2012 on waste electrical and electronic equipment (WEEE),
Spectrafuge Mini Centrifuge is marked with the crossed-out wheeled bin and
must notbe disposed of with domestic waste.
Consequently, the buyer shall follow the instructions for reuse and recycling of
waste electronic and electrical equipment (WEEE) provided with the products
and available at the following link: www.corning.com/weee

Warranty Statement
Corning Incorporated (Corning) warrants that this product will be free from defects in material and
workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL
OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.
Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof
that proves defective in material or workmanship within the warranty period, provided the
purchaser notifies Corning of any such defect. Corning is not liable for any incidental or
consequential damages, commercial loss or any other damages from the use of this product.
This warranty is valid only if the product is used for its intended purpose and within the guidelines
specified in the supplied instruction manual. This warranty does not cover damage caused by
accident, neglect, misuse, improper service, natural forces or other causes not arising from
defects in original material or workmanship. This warranty does not cover motor brushes, fuses,
light bulbs, batteries or damage to paint or finish. Claims for transit damage should be filed with
the transportation carrier.
In the event this product fails within the specified period of time because of a defect in material or
workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-
1110; Canada: 1-978-442-2200. For other regions of the world, please visit
www.corning.com/lifesciences or see the included instruction manual for a list of World Wide
Support Offices.
Corning’s Customer Service team will help arrange local service where available or coordinate a
return authorization number and shipping instructions. Products received without proper
authorization will be returned. All items returned for service should be sent postage prepaid in
the original packaging or other suitable carton, padded to avoid damage. Corning will not be
responsible for damage incurred by improper packaging. Corning may elect for onsite service for
larger equipment.
Some states do not allow limitation on the length of implied warranties or the exclusion or
limitation of incidental or consequential damages. This warranty gives you specific legal
rights. You may have other rights which vary from state to state.
No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend
the period of this warranty.
For your reference, make a note of the serial number, date of purchase and supplier here.
Serial No. ____________________ Date Purchased _________________
Supplier _____________________________________________________
Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended for use in diagnostic
or therapeutic procedures. Corning makes no claims regarding the performance of these products for clinical or diagnostic
applications.
Please register your product online at:
www.labnetinternational.com

NOTES

[e-mail]
www.labnetinternational.com
LN1010000