Labnet AccuPlate D0300 User manual

AccuPlate™
Analog Hotplate,
Stirrers,
Hot Plate Stirrer
User Manual
D0300
D0300-230V
D0310
D0310-230V
D0320
D0320-230V
October 2014 Version 1.0
LIT M03001

About This Manual
This manual is designed to assist you in optimal usage of your new hot plate, stirrer or
hotplate stirrer.
Product Voltages
Hot plates, stirrers, and stirrer/hot plates are available in different voltages. Before initial
use, check that the unit you received is the correct voltage for your location.
Warranty Registration
Filling out and mailing the attached Warranty Registration Card or submitting this infor-
mation online at http://www.labnetinternational.com/product-warranty-registration will
validate the hot plate, stirrer or hotplate stirrer’s warranty.
Table of Contents
Safety Information 3
Operating Conditions 4
Product Controls and Indicators 5
Instructions for use (Stirring and Heating) 6~7
Product Repair 7
Product Maintenance and Storage 7
Technical Specifications 8
Accessories 8
Product Size and Dimensions 8
Certifications 10
Warranty Statement 11
Notes 12
2

Warnings
Personal Injury
• Do not use this product in a manner other than as stated in the Operating Conditions section
of this manual as the protection provided by the equipment may be impaired.
• This product is designed for use in laboratory environments by persons knowledgeable in safe
laboratory practices.
• Always wear safety glasses and other appropriate protective equipment when operating this
product.
Electric Shock
• This product must be connected to a grounded power outlet for safe functioning.
• Use only the power cord supplied with the product.
• The power cord is the device available for full disconnect from mains input.
Safety Information
This instruction manual contains important operating and maintenance instructions which
must be read, understood, and followed by the product user. Failure to use this product ac-
cording to this instruction manual may degrade or defeat the protection normally provided
by this product. Read this instruction manual prior to product use and keep this instruction
manual for future reference. The precautions are composed of DANGER, WARNING and CAU-
TION.
Product Symbols
DANGER Indicates a potentially or imminently hazardous situation which,if not
avoided,could result in death or serious injury.
WARNING Is used to alert operators to an operating procedure,Pratice or condition
that,if not strictly observed,can result in severe injury or loss of life.
CAUTION Indicates a potentially hazardous situation that may result in minor or
moderate injury.
WARNING CAUTION
Touching the reactor block surfaces and vials
while hot can cause serious burns.
Hot Surface
WARNING CAUTION
This product requires a protective earth connection.
If not provided with a plug on a cord,connect positive earth to this terminal.
Protective
Earth Ground
3

• Position the product for use so that the power cord can be easily disconnected without having
to move the product.
• Disconnect the power cord before moving or cleaning the unit.
Product Damage
• Keep the product dry and clean.
• Do not immerse the product for cleaning.
• Do not heat or stir volatile or ammable materials.
• The ceramic coated top surface may break if impacted.
• The maximum sample volume stirring capacity is 5L
• These units are not explosion or spark proof.
• Do not operate this product near volatile or ammable materials.
• Do not use this product with a metal vessel.
Operating Conditions
Your Labnet hot plate, stirrer or stirring hot plate is a general purpose heating and/or stirring plate
designed for laboratory procedures requiring precise control of temperature and/or stirring speed.
Your hot plate, stirrer or stirring hot plate has the following properties:
1) Ceramic coated top plate: Ceramic coated top plate is corrosion proof, temperature resistant
and resists aggressive uids.
2) Coated in a pure white plate allows for easy observation of sample color change during use.
3) The top plate allows for quick thermal conduction and uniform surface temperature.
4) This device uses an electronic Analog temperature controller to control temperature
5) The Labnet Hot Plate Stirrers were designed to start and stop smoothly to prevent uid spill
over from rapid turnover and decoupling of stir bar.
6) The Labnet hot plate has an electronic feedback control which will accurately maintain tem-
perature.
Labnet hot plates, stirrers, and stirrer/hot plates are designed to provide safe functioning under the
following conditions:
• Indoor use
• Altitude up to 2000 meters (6,500 feet)
• Ambient temperatures of 0°C to 40°C
• Product should be placed on a at surface at least 30.5 cm (12”) from walls, 122 cm (48”)
from ceilings, and 30.5 cm (12”) from other hot plates if using multiple units.
• Maximum relative humidity of 85% for temperatures up to 31°C, decreasing linearly to 50%
relative humidity at 40°C.
• Pollution Degree 2: Any foreign matter that may accumulate on or within the product during
normal use is not electrically conductive.
• Installation Category II: Product is designed for connection to an electrical branch circuit inside
a building with main supply voltage uctuations not exceeding ±10% of the nominal voltage.
4

Product Controls and Indicators
Front side
Rear Side
Hot Top
Indicator Lamp
Heat Control
Knob
Stir Control
Knob
Temperature On
Indicator Lamp
Ceramic Coated
Top Plate
Speed On
Indicator Lamp
Power
Switch
Support Rod
Holder
Power Inlet with
fuse holder
Data Label
5

Instructions for Use
1) Turn temperature and speed to zero before plugging in. And connect the Main power cord
topower supply. Place your container or heating bath with the magnetic stirrer bar. Stirrer bar
should be placed in center of hot plate
2) Turn Power Switch ON.
Stirring Instructions
D0310, D0320
1. Fill vessel with solution to be stirred.
2. Place stir bar into vessel.
3. Turn power switch ON. Then Hot Top Indicator Lamp will illuminate.
4. Turn Stir Control Knob until the desired speed.
5. Speed On Indicator Lamp will illuminate when the motor runs.
6. Heating and stirring can be performed simultaneously on the D0320 models which offer both
heating and stirring functions.
7. When the desired stirring is complete, turn the Stir Control Knob to “0” position. Allow stir bar
to cease rotation before removing the vessel from the unit.
8. Disconnect Main power cord from the unit.
9. Keep the product dry and clean disconnecting Main power cord when the unit is not used for
a long time.
Note:
1) Range of speed control : 100~1500 RPM
2) Speed control knob in extreme left (CCW) position stops operating.
3) If motor does not run upon turning the knob, increasing until 100rpm or more
Please note that the viscosity of the stirred material will affect the ability of the stir bar to remain
coupled to the rotating ring magnet. Materials of high viscosity must be stirred at slower speed
settings.
6
No Desc Analog Hotplate Stirrer
Hot Top Indicator Lamp
Heat Control Knob
Temperature On Indicator Lamp
Speed On Indicator Lamp
Stir Control Knob

7
No Desc Analog Hotplate Stirrer
Hot Top Indicator Lamp
Heat Control Knob
Temperature On Indicator Lamp
Speed On Indicator Lamp
Stir Control Knob
Heating Instructions
D0300, D0320
1. Fill vessel with solution to be heated.
2. If using a D0320 and the stirring function, place stir bar into vessel.
3. Place vessel in the center of the top surface.
4. Turn power switch ON. Then Hot Top Indicator Lamp will illuminate.
5. Heat Control Knob until the desired temperature.
6. Temperature Indicator Lamp will illuminate when the heater runs.
7. When the desired heating is complete, turn the Heat Control Knob to “0” position. And
remove the vessel from the unit.
8. Disconnect Main power cord from the unit.
9. Keep the product dry and clean disconnecting Main power cord when tehn unit is not used
for a long time.
Caution: The Hot Top Indicator will turn OFF when the power switch is OFF even if the
temperature of the top surface is still hot to touch.
Product Repair
There are no direct user serviceable components inside this series of products.
Please contact you Labnet Distributor for repair or maintenance issues.
Product Maintenance and Storage
Caution Disconnect the plug before cleaning !!
Power
Inspect the power cord regularly and replace if damaged. Use only replacement power cords avail-
able from Labnet or authorized Labnet product distributors.
Top Plate
• The top plate may break during use if not properly maintained.
• Keep the top plate clean. A nonabrasive cleaner may be used to clean the top plate.
• Inspect the top plate for damage during cleaning.
• Discontinue product use if the top plate is chipped, etched, or shows excessive scratching.
• Contact your Labnet Distributor or Labnet Customer Service for top plate replacement.
General
• It is important to keep this product dry and clean.
• Remove minor exterior liquid spills promptly.

8
• Clean exterior surfaces with a nonabrasive cleaner. Do not clean this product with substances
such as alcohol or benzene. (Use neutral detergent.) Do not reconnect product to power input
until all cleaned surfaces have dried.
• If liquid or wet solid material gets inside the product, immediately disconnect power to the
product and discontinue use. Contact Labnet for additional instructions regarding interior spills.
• Do not disassemble, modify, revise or repair this product. This may be a cause a
malfunction,electrical fire.
• We recommend to store the item and its components in its original box, or a similar container
that offers adequate protection against damage in transit. Tape the box securely.
Technical Specifications
TYPE D0300 D0310 D0320
Hot plate Magnetic Stirrer Hotplate Stirrer
Temperature
Range Max. 380℃Max. 380℃
Display Scale(temperature) Scale(temperature)
Controller Analog temperature
controller Analog temperature controller
Watts 680W 15W 695W
Stirring
Speed 100 ~ 1500 rpm
Speed display Scale(rpm)
Capacity up to 5L
Speed Controller Feedback control
Top Plate Ceramic coated top plate
Dimensions Plate area(mm) 180 X 180
Overall(WxDxH) 200 X 310 X 107(mm)
Electrical Supply AC 110V 50/60Hz or 220V 50/60Hz
Product Codes and Accessories
Product Code Description
D0320 Hot Plate & Magnetic Stirrer, 120V
D0310 Magnetic Stirrer, 120V
D0300 Hot Plate, 120V
D0320-230V Hot Plate & Magnetic Stirrer, 230V
D0310-230V Magnetic Stirrer, 230V
D0300-230V Hot Plate, 230V
Product Code Accessories
D0300-SR Support Rod (included w/D0320&D0300)

9
EQUIPMENT DISPOSAL
This equipment is marked with the crossed out wheeled bin symbol to indicate that this equipment
must not be disposed of with unsorted waste.
Instead it’s your responsibility to correctly dispose of your equipment at
lifecycle-end by handing it over to an authorized facility for separate collection
and recycling. It’s also you responsibility to decontaminate the equipment in
case of biological, chemical and/or radiological contamination, so as to protect
from health hazards the persons involved in the disposal and recycling of the
equipment.
For more information about where you can drop off your waste equipment, please contact your
local dealer from whom you originally purchased this equipment.
By doing so, you will help to conserve natural and environmental resources and you will ensure that
your equipment is recycled in a manner that protects human health.
Thank you
Labnet International, Inc,.
31 Mayfield Ave., Edison, NJ 08837
(P) [phone] (F) [phone]
Email: [email protected]
www.labnetinternational.com

10
Declaration of Conformity
Number : CE M3001
Labnet International, Inc,., 31 Mayeld Ave., Edison, NJ 08837 USA
Labnet International declares that the devices described below are in conformity with the EC directives
listed. In the event of unauthorized modification of any of the devices listed below, this declaration becomes
invalid.
Device Name: AccuPlate™ Analog Hot Plate
AccuPlate™ Analog Hot Plate & Magnetic Stirrer
AccuPlate™ Analog Stirrers
Device Models Numbers: D0300
D0300-230V
D0310
D0310-230V
D0320
D0320-230V
Relevant EC Directives: Low Voltage Directive 73/23/EEC
As amended by 93/68/EEC
EMC Directive 89/336/EEC
As amended by 92/31/EEC and 93/68/EEC
RoHS Directive 2011/65/EU
WEEE 2012/19/EU
Harmonized Standards: IEC 61010-1:2001 (Second Edition)
IEC 61010-2-010:2003 (2nd Edition)
EN 61010—2-051:2003 (2nd Edition)
EN 61326-1
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
Date: October 7, 2014
Peter Will
Product Line Manager
October 2014 Version 1.0
LIT M03001