lamber P550-dy-CVP-S User manual

INSTRUCTIONS
MANUAL
UTENSIL WASHER
REV.10-2016
P550-dy
P550-dy-CVP-S

2

3
DECLARATION OF CONFORMITY
The following :
LAMBER snc di Affaba F. e C. – Via Italia 6 – 26855 Lodi Vecchio (LO) ITALY
Declare under our responsibility that:
Apparatus: WARE WASHER
Trademark:LAMBER
Manufacturer :LAMBER
Type / Model P550-dy / P550-dy-CVP-S matr………………...
for which this declaration refers to the conformity of the following standards:
Safety of household and electrical appliances - General requirements EN 60335-1(2012)
Safety of household and electrical appliances - Part 2^ Particular requirements for commercial electric dishwashing machines EN
60335-2-58 (2005) + A1 (2008) + A11 (2010).
Household and similar electrical appliances – Electromagnetic fields – Measurement methods for electromagnetic fields of
household appliances and similar apparatus with regard to human exposure EN 62233 (2008)
Limits and methods of measurement of radio disturbance characteristics of electrical motor-operated and thermal appliances for
households and similar purposes, electric tools and similar electric apparatus - EN 55014-1 (2006) + A1 (2009) + A2 (2011)
Limits for harmonic current emissions (equipment input current
 16 A per phase) - EN 61000-3-2 (2014) or >16A and  75A EN
61000-3-12 (2011)
Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current
 16 A. EN 61000-3-3
(2013) o >16A e 75A EN 61000-3-11 (2000)
Immunity requirements for household appliances, tools and similar apparatus. Product family standard EN 55014-2 (1997) + A1
(2001) + A2 (2008)
Safety of machinery Basic concepts, general principles for design - Basic terminology, methodology – EN ISO 12100 (2010).
on the basis of what is foreseen by the Directives
2004/108/EC and 2006/42/EC.
We decline any responsability for injuries or damage derived from machine misuse, abuse by others or improper machine maintenance or repairs.
(date) li 01/2016
The administrator
technical file case manager : Ing Roberto Affaba
address : via italia 6 – 26855 – Lodi Vecchio (LO) Italy

4
WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT DIRECTIVE (WEEE,RAEE in Italy) 2002/96/EC AND
SUBSEQUENT 2003/108/EC
The marking shown below indicates that the product cannot be disposed of as part of normal household
waste. Electrical and Electronic Equipment (EEE) can contain materials harmful to health and the
environment, and therefore is subject to separate waste collection: it must be disposed of at appropriate
waste collection points or returned to the distributor against purchase of new equipment of similar type or
having the same functions.
The directive mentioned above, to which make reference for further details, provides for punitive actions in
case of illegal disposal of such waste.
Lamber guarantees a percentage of recovery at least of 90% in medium weight for each equipment. The
80% - always as regards the medium weight- of recovered material is recycled or reused.
LAMBER, manufacturer of this equipment, is enrolled in the Italian WEEE Register – the Register of
Producers of Electrical and Electronic Equipment- from the 18th /02/2008 with the number
IT08020000000617.

5
INDEX
General notes pag. 06
Introduction and safety notes pag. 07
Learn to use the appliance pag. 08
First section - FOR THE USER pag. 09
Control panel pag. 10
Working and use pag. 11
Instructions before washing pag. 11
Washing pag. 12
Achievements pag. 13
Stand by, self-washing pag. 14
Instructions drain pump pag. 15
Descaling pag. 15
Automatic message list pag. 16
Placement of objets pag. 17
Cleaning and preventive maintenance pag. 18
Daily cleaning of the interior of the ware-washer pag. 19
Detergents, rinse additives, descaling, sanitation pag. 23
Inconveniences – Possible causes-remedies pag. 24
Useful advices for the maintenance of stainless steel pag. 25
Second section - FOR THE INSTALLER pag. 27
Installation pag. 29
Electrical connections pag. 31
Water connections pag. 32
Dispenser of washing, rinsing and descaling (programming) pag. 33
Descaling cycles (programming) pag. 34
Replacing of the detergent and washing of dispenser washing pipes pag. 35
Programming – user pag. 36
Connection scheme pag. 40
Wiring diagram pag. 41
Components pag. 45
Specifications pag. 46

6
GENERAL NORMS ENGLISH
Thank You for purchasing our Ware-washer.
Perfect washing-up results as far as hygiene concerns and a correct operation of the Ware-washer can be
assured only in case the instructions reported in the present manual are carefully followed.
We hope the information reported in the present manual will be helpful to You.
They are based on data and on our best updated knowledge.
Carefully read the Instructions reported in the manual, recommendations and suggestions included.
Carefully read the terms of sale too, even the ones limiting warranty.
This appliance in not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance (EN 60335-2-102/7.12).
The Ware-washer machine has to be installed in an area with air recirculation and that complies with the
local work hygiene rules !

7
INTRODUCTION
AND SAFETY NOTES
INTRODUCTION
- The machine is an Industrial Ware-washer.
- Noise level of the machine: <70 dB(A) - (Norms EN ISO 4871 and EN ISO 11204)
PRELIMINARY OBSERVATION
Carefully read the instructions reported in the present user manual, as it gives important indications about safety of
installation, operation and maintenance:
- carefully keep the present manual for further consultations;
- the illustrations and drawings showing the machine are intended for general reference only and are not
necessarily accurate in every instance;
- the dimensions and characteristics of the machine, given in this Manual, are not to be considered binding and
may be changed without prior notice;
- once removed the packing material, check that all the equipment is present. If there is any doubt, do not use it and
contact qualified personnel. The packing elements (plastic bags, nails, etc.) should be kept away from children,
because they are dangerous.
GENERAL SAFETY REGULATIONS
THIS SAFETY CODE HAS BEEN COMPILED IN YOUR INTEREST. Strict adherence to these rules will reduce the risks
of injury both to yourself and to others;
Personnel working with this machine must adhere strictly to all statutory safety regulations as well as the specific rules
listed below. Failure to do so may result in personal injury and damage to the machine;
- DO NOT attempt to move, install, set up or operate this machine until you have read and fully understood this
Manual. If doubt persists, ask your supervisor;
- never leave tools, parts or other loose material on or in the machine;
- Before switching the equipment on, make sure that the model plate data conform to those of the electrical and
water distribution network;
- remember that even with the mains indicator in the “OFF” position, the incoming cables are still live;
- BEFORE starting the machine or the cycle, after any maintenance or repair work, make sure all protective are
correctly installed;
- be vigilant at all times, remember that your safety and that of your fellow workers depends on you;
- when moving or lifting the machine, care must be taken to comply with all the relevant regulations governing such
operations;
- installation should be carried out by qualified personnel according to the manufacturer's instructions.
- this equipment should be destined to the use which it has been conceived for. Any other application should be
considered improper and consequently dangerous;
- the equipment should only be used by personnel trained for its use;
SPECIAL SAFETY REGULATIONS
- adjustement and repairs must be carried out only by qualified personnel. Repair carried out by unskilled personnel
may be dangerous;
- perfect washing-up results as regards hygiene and a correct operation of the washing machine can be assured
only in case the instructions reported in the present handbook are carefully followed;
- the machine must be used only by authorized personnel who must comply with sanitary measures;
- do not leave the machine in an environment with temperatures lower than 0°C;
- the machine protection degree is IP21, therefore it should not be washed with direct high pressure
jets of water;
- If the power cable is defective, it must be replaced by your manufacturer or by a technical assistance
service or by a qualified technician in order to avoid risks.
RESIDUAL RISKS
Although the appliance is equipped with the above-mentioned safety devices, danger of burns to upper limbs persists.
Avoid dipping your naked hands into the soapy hot water present in the tanks. This can cause burns and skin irritations.
In this case, immediately rinse them with plenty of water.
When the machine is working, do not open the inspection doors too quickly.

Water inlet 3/4"
Stainless steel
Upper rotating washing
Steam condenser
Fan
ExtractableSteam condenser filter
Stainless steel
Lower rotating washing
Stainless steel Tank filters
Stainless steel
Suction pump filter
Double skin with insulation 14mm
Tank with slanting bottom
Autodraining
washing pump
Body,tank and Top in
Stainless steel construction
Stainless steel
Boiler with insulation
Stainless steel
Lower rotating rinsing (cone 90°)
Stainless steel
Upper rotating rinsing ( cone 90°)
Overflow
Water outlet ø 32mm
Rinse-aid dispenser
Learn to use the appliance
(only )P550-dy-CVP-S
(only P550-dy-CVP-S)

INSTRUCTIONS FOR THE USER

110
A
C
D
E
Dis.1
CONTROL PANEL
Cycle pushbutton
Wash time selection
pushbutton
Interactive display
Programming
pushbutton
B
Main switch
09-2013

11
ENGLISH
First Section - FOR THE USER
WORKING AND USE
NOTE:
- When the objects to be washed present burnt crusts, or a long time is elapsed from cooking up to the
time of washing, it is necessary to make a previous softening in water at 50°C, by using an appropriate
softeningproducts;
- Never deep naked hands in detergent water;
- While the machine is running, never open the door too rapidly;
- Only use specific anti-frothing detergents.
INSTRUCTIONS BEFORE WASHING
BEFORE STARTING THE WORKING OPERATION MAKE
SURE THAT:
- the cock is open;
- the filters and the overflow are in
their housings;
- the wash arm and the rinse arm are free to
pivot;
- rinse aid and washing powder dispenser
containers are loaded.
THEN PROCEED:
1 - Put the detergent directly into the tank, by
paying attention to distribute it uniformly
on the filters, the quantity being according to
supplier's instructions.
N.B. When using chlorinated detergent, it is
suggested to use an automatic dispenser; if
otherwise, brownish spots might appear on the
surfaces, because of chlorine reactions, if
powering the detergent directly in the tank.
CAUTION: Observe the safety notes and
dosage data for the use of chemicals. During
the use of the chemical substance wear
protective clothing, gloves and protective
glasses. Do not mix different cleaning
products.
TURN ON THE MACHINE and
operating state of emergency.
2- Turn on the power using the switch on the
wall and press the switch "A" placed on the
control panel (DIAGRAM.1).
You will see the serial number of the machine
followed by the logo Lamber.
Close the door of the ware-washer.
Please pay attention to the opening and
closing of the door of the machine. Do not use
the machine if you are wearing clothes/items
that could get entangles in the machine parts.
As they can limit personnel’s regular moving
ability!
Press at this point the key switch “A” on the
control panel (draw 1)
At this point the LED will turn green and the
interactive display will show “Fill phase 1” that will
signal the start of the filling phase of the tank.
The filling phase is implemented in two stages.
In STEP 1 begins the load of the tank with water
from the water mains; in STEP 2 continues the
filling but also begins a warm-water washing.

12
Note: If the machine is equipped with water
softener, during the FILLING PHASE 1 it will be
made to one or more cycles of Regeneration and
a subsequent Resins’ Washing.
Attention: during tank filling don’t open the hood
of the dishwasher!!
Attention!
If during the loading phase, appears the message
“BREAK TANK”, this means that you’re filling up
with water the rear Break Tank.
If after 5 minutes the data is still flashing in
alternation with the inscription FILLING PHASE 1,
you will see the word ALARM BEREAK TANK and
this will means that there may by a problem in the
tank loading. (Call the Technical Assistance
Service!)
At the end of the filling phase of the tank on the
interactive display will appear the following
information (from left to right):
-Temperature of washing;
-Time of washing;
-Number of cycle;
-Temperature of rinsing..
The data of the temperature Tank and Boiler,
flashes slowly and increases in value, indicating
the current warming of the water in the boiler.
When temperature has reached, the data stops
flashing.
Attention !
The machine is programmed at the factory so you
can start the washing programm after filling the
tank up to the required level.
However, before you start the cycle, make sure
that the machine has reached the ideal
temperature range (55°C for washing and 85°C
for rinsing):
In any case, the rinse will start only in
temperature regime reached. The duration of the
washing time chosen will then be continued until
it reaches the set temperature ((Thermocontrol).
WASHING
3- Open the door of the machine and insert
the basket.
N.b.The display informs you when the top of the
dishwashers is open.
4- Place the objets in the basket minding to
previously remove all solid waste and fat.
N.B.: When the objects to be washed present
burnt crusts, or a long time is elapsed from
cooking up tothe time of washing, it is necessary
to make a previous softening in water at 50°C,
by using an appropriate softening product.
For a correct positioning of the objets see the
specific paragraph on page 17.
5- Select the time of the washing cycle by
pressing the time selection “D”
,
According to the following criteria:
- cycle 1 :short 1 minute ;
- cycle 2 : intermediate 2 minutes ;
- cycle 3 : long 3 minutes ;
- cycle 4 : infinite 15 minutes ;
The duration of the cycle must be chosen
according to the type of dirt to be removed from
the dishes.
See paragraph specifically for custom
programming, in the section dedicated to the
installer.
6- Close the door of the ware-washer.
Start at this point the washing cycle of the
chosen duration comprising in addition to washing
a rest period of 5 seconds, and a rinsing phase
lasting 15 seconds with clear water at 85°÷90°C.
(only for P550-dy-CVP-S)
At the end of the washing phase there is the
automatically activating of the fan for suction of
the vapors. This aspiration continues for a
programmable time from 0” a 60” beyond the end
of the rinse seconds ( default 20“) .
A beep indicates the end of the cycle.

13
(only for P550-dy-CVP-S)
To temporarly pause the cycle, simply open the
door of the ware-washer.
Closing it, the cycle will start again at exactly the
point were it was interrupted.
It is possible at any time to stop the wash cycle by
simply pressing the button again cycle “B”
.
When you restart the cycle, this will restart from
the beginning.
(be carefull! During the cycle, at the opening of
the hood is pressed also the fan for fume
extraction for a maximum time of 20 seconds –
only to P550-dy-CVP-S)
7- At the end of the wash cycle , the
message “END WASH” will appear followed by a
short beep.
The LED turns off and the B button appear the
temperature data and the data number and
duration of the cycle.
Open thedoor of the ware-washer.
Remove the basket and tilting it, shake it lightly to
bring down the remaing drops. Allow to dry the
dishes by evaporation, then remove them from
the basket, taking care not to touch the inside
edge of the same. Then put them on hygienic
shelves.
To continue the wash load another basket and
close the door. The cycle will restart
automatically.
If you want to change the wash cycle, before
closing the door, you will need to select the new
cycle by pressing the time selection “D”.
Temperature data display: to view temperature
data during the wash cycle, it is necessary to
press the push-botton . You will see the
temperature data for 3”.
If you want to fix the values of temperature for
the whole duration of the selected cycle, it is
necessary to press the button for 3”.
To re-display the data of the wash cycle, it is
necessary to press the switch .
Attention! At the next cycle the temperature data
will not be displayed automatically, but the data
will appear in the wash cycle.
ACHIEVEMENTS
Any deficiency in the washing process is
obvious when dirty residuals are visible. Any
halos might be caused by an insufficient rinsing:
in this case, check that the rinsing jets are clean
and that there is a sufficient pressure in the
water distribution network.
In case you find residuals, check that:
• the washing jets are clean
• there is some detergent
• the pump suction filter is clean
• objects in the rack are placed in a correct
position.

14
STAND BY-ECONOMY
(only available on a machine with automatic
start!):
The stand-by function allows you to keep the
machine closed at rest, keeping active heating
functions.
machine «ON»
Door
open
To start cycle
pressbutton
keep
button
pressed
for 3 sec.
1
2
Stand-by : with open door and the machine is in
“ON”, press the cycle “B” push-button for 3
seconds, then closing the door, the machine will
not operate the wash cycle while maintaining
active heating functions.
The display shows the word “ECONOMY”. The
temperature of the heater stabilizes at 60°
reducing the consumption of energy.
Attention!: make sure, after you start the
stand-by function to close the doord to keep
the wash tank hot and not disperse heat!
To restart the cycle, put the door down and press
the push-button “B”.
Automatic Stand-by : after 10 minuters of non-
use of the machine, with the door open, it
automatically activates the STAND BY-
ECONOMY, (the display shows the word
ECONOMY P*)
To restart the cycle, put the door down and press
the push-button “B”.
If the machine is not used for 1 hour, the same
turns off completely (the machine “OFF”, even
turning off the heating elements).
Turn on the machine by pressing the push-
button”A”.
To restart the cycle, put the door down and press
the push-button “B”.
SELF-WASHING
The function of self-washing allows you to make
a cleansing cycle at the inside of the washing
tank.
The inside of the washing tank is cleaned with
water coming from water network.
machine «OFF»
Door
closed
Remove the
overflow
Wait the End
of the drain
(with drain pump
press button)
keep
button
pressed
for 3 sec.
1
2
3
4
- Self-washing cycle: with the machine ”ON” do
the following operations::
-1 Put the machine OFF by pressing the
push-button “A” ( led off)
-2 Remove the overflow of the tank and wait
until same is empty;
For machines equipped with drain pump, see the
instructions at the specific paragraph.
For machines without drain pump:
Visually check that the tank is empty,
-3 Close the door of the machine ;
-4 Hold the ” ”button for 3 seconds.
ATTENTION: before your press the ” ”, button,
make sure that the display shows the logo lamber
””.
In case it is off, turn the machine on by pressing the
switch “A” and then pressing it again to to turn off
again the push button “A”
The logo Lamber will reappear and will then be able to
start the function SELF-WASHING holding down the
select push button ” ”for 3 seconds
On the display you will see the words “SELF-
WASHING” with the time bar that indicates the
icrease for the duration of the cycle of 5 or 10
minutes depending on the time of rinse set by
default
If you want to stop the cycle SELF-WASHING, it
is sufficient to press the switch “A”.

15
DRAIN PUMP INSTRUCTIONS (optional)
(only for machines with drain pump)
The pump discharge function allows you to
automatically download the wash tank at the end
of the workday.
machine«OFF»
Door
open
Remove the
overflow
1
23
keep
button
pressed
for 3 sec.
The operation of the discharge pump is
automatic only during the cleaning cycle to
drain the excess water that enters during the
rinsing phase
At the end of the working day, to discharge
the tank completely, you must perform the
following steps:
-1 Put the machine OFF by pressing the
switch “A” (the display shows LAMBER
logo);
-2 Open the door of the machine;
-3 Remove the OVERFLOW from the tank
4- Then press the “B” cycle-button for 3
seconds
Alternately flash the words “DRAIN” and
“REMOVE OVERFLOW”
(N.B. The word “REMOVE OVERFLOW” will
disappear only to the closing of the door)
The discharge stops automatically after about 5
minutes.
The discharge can be interrupted at any time by
pressing the cycle-button “B”
After drainig, the machine will turn off
completely (display OFF).
Replace the overflow into place and close the
door.
DESCALING (optional)
(only for machine with drain pump and
dispenser )
The descaling function is a cycle that leads
descaling liquid in the pipelines of rinsing, in the
washing tank and boiler allowing the removal of
limescale deposits from the water products.
The cycle lasts about 35 minutes.
For an average water limestone is recommended
cycle activation at least once a week.
The frequency may vary depending on type of
water.
machine «OFF»
Door
closed
Remove the
overflow
keep
button
pressed
for 3 sec.
keep button
pressed for 3 sec
and w . ait the End
of the drain
1
2
3
4
To make the cycle do the following operations:
-1 Punt the machine OFF by pressing the
switch “A” (led off)
-2 Remove the OVERFLOW from the tank;
-3 Press the “B” button for 3 seconds and
wait for the complete emptying of the
tank;
-4 Close the door of the machine;
-5 Then press the “E” button for 3
seconds
At the end of the descaling cycle (approx. 35
minutes) will appear on the LED the words
“END OF THE DESCALING CYCLE”.

16
List of automatic MESSAGES
On the display may appear some messages to
inform about the status of the cycle start of
abnormalities. Below is the eXplanation of some
MESSAGES that appear on the display
automatically.
1-BREAK TANK :
This indicates that the tank of Break Tank is
filling of water to reach the required level.
2-ALLARME BREAK TANK:
This indicates a fault in the operating system:
lack of water mains, valve not functionning: Call
Customer Service!
3-ECONOMY :
After 10 minutes of non-use of the machine with
hood open, it appears the word ECONOMY.
The temperature of the heater stabililzes at 60°
reducing the consumption of energy.
4-OFF
If no button is pressed in 1 hour, the message
“OFF” will appear and the machine turns off.
5-THERMOCONTROL :
This indicates that the washing cycle will be
extended to reach the ideal temperature for
rinsing
This message is accompanied by the value of the
temperature. This gives flashes and increments
until it reaches the programmed temperature, at
which may start the rinsing phase.
6-REMOVE OVERFLOW :
This indicates that the overflow has to be
removed to perform the selected operations (self-
washing, descaling or discharge of the tank)
The data is highlighted even if in reality you have
already removed the overflow, but will disappear
automatically after 10 seconds after you close
the hood of the dishwasher.
7-REGENERATION IN PROGRESS :
(only for machines with built-in water softener).
It indicates that a cycle of regeneration of the
resins varying from 30” to 90” seconds is in
progress.
8- WASH OF THE RESINS :
(only for machines with built-in water softner).
It indicates that a washing cycle of the resins of
the duration of 10” seconds is in progress..
9-SALT :
(only for machines with built-in water softener)
It indicates that there is a lack of salt into the
container. Add big pads of salt into the container
as per the specifications given to you by your
provider.
10-SERVICE :
It Iindicates that you need to do maintenance
work. The scheduled maintenance service allows
you to control all the devices and efficiently
maintain your dishwasher over the time. Normal
functioning is still guaranteed. It is well worth
however not to wait too long to make the
intervention.
List ALARMS!
Alarm: A3-TEMP.SENSOR : this message
indicates that the probe of the tank temperature
thermostats or boiler is defective. Call the
Technical Support Service!!
Alarm: A2-HIGH TEMP. : this message indicates
that the temperature in the boiler is greater than
105°C. Call the Technical Support Service!
Alarm: BOILER PROBE FAILURE. : this
message indicates that the probe of the boiler is
not working properly. In this case the functioning
of the resistance of the boiler and the
Thermocontrol are disabled.
Call the Technical Support Service!
Alarm: TANK PROBE FAILURE: this message
indicates that the probe of the washing tank is
not working properly. It is disabled in this case
the functioning of the washing tank resistance.
Call the Technical Support Service!

ITL-3 cod.CC00059 (1x)
520
580
CLP-52 cod.CC00089 (1x)
H max
640 mm
capacity:
n. 2 dim.330x165 mmcontainers
capacity:
n. 4 containers dim.330x165 mm
Clearance
OBJETS POSITIONING
To achieve optimal cleaning results, make sure that objets are correctly stored
inside the machine
Warning !
Only use the baskets
supplied with the pot-washer
!
Insert the baskets inside the
machine with the objets as
shown in the picture.

CLEANING AND PREVENTIVE
MAINTENANCE
PRECAUTION AND CLEANING
INSTRUCTIONS
- IMPORTANT : Before carrying out the
cleaning and maintenance operations,
disconnect the equipment from the mains
power supply:
Attention. Before carrying out cleaning the
inside of the machine, make sure that there are
no foreign objects that could damage the rusty
steel inside the tank. The eventual rust particles
could come from non-stainless steel dishes, from
baskets or damaged water pipes not rust-proof.
-Follow the directions on the maitenance in
this guide;
-Wear protective clothing and gloves when
challenged elements are impregned with
clearing solution;
-high temperatures can be reached inside
the machine (90°C). After power supply has been
removed, wait until the machine has reached
room temperature, before working on it.
-never leave tools, parts or other loose
material in or on the machine;
-Chek that there are no rusting foreign
bodies, because of the material “stainless
steel” could begin to rust. Rust particles can
come from non- stainless steel dishes or
damaged wire baskets.
- Do not wash the machine and the area
surrounding it with fire hydrants, steam jets
of high-pressure cleaners;
- When clearing the floor be careful not
to saturate the base of the machine, in order
to avoid a prolonged stagnation of water;
- To clean the inside of the machine, use
a brush or a soft cloth;
- To clean the machine do not use
abrasive cleaners;
-BEFORE starting machine or cycle, after
any maintenance or repair work, make sure
all protectives are correctly installed;
DAILY MAINTENANCE
-Turn off the machine by pressing the
switch “A” and drain the water from the
tank by removing the overflow;
- Wait until the water is drained and there is
no debris on the bottom of the tank.
- Proceed to the specific operation of daily
clearing as described on the next page
Please pay attention to the opening and
closing of the door of the machine. Do not use
the machine if you are wearing clothes/items
that could get entangles in the dishwasher parts.
As they can limit personnel’s regular moving
ability!
-(only for P550-dy-CVP-S) Clean the filter
of the steam condenser that is placed in the
upper part of the hood;
- If there is an extended downtime is
advisable to prevent the formation of
unpleasant odors and leave the hood
raised.
- When the machine is to remain idle for a
long time, drain all the water from the
boiler (the drain plug is located on the
lower side of the boiler) and from the
electropump. Also leave the wash tank
open.
NEVER WASH THE EXTERNAL PART
OF THE MACHINE WITH A WATER JET

DAILY CLEANING OF THE INTERIOR OF THE DISHWASHER
Attenzione. Prima di effettuare la pulizia dell’interno della macchina, assicurarsi che non siano presenti
oggetti estranei arrugginiti che potrebbero danneggiare l’acciaio inossidabile all’interno della vasca. Le
eventuali particelle di ruggine presente potrebbero provenire da stoviglie non inossidabili, da cestelli
danneggiati o condutture dell’acqua non a prova di ruggine.
Open the door of the machine
Please pay attention to the
opening and closing of the door of
the machine. Do not use the
machine if you are wearing
clothes/items that could get
entangles in the dishwasher parts.
As they can limit personnel’s regular
moving ability!
Unscrew the upper rinse arm.
Remove the internal tank filter
Unscrew the lower rinser arm
Remove the lower washing
arm
Remove the upper washing
arm
Remove the tank filter
ATTENTION! Daily
disassemble the lower and
upper wash arms by
working on the „big“ ring
nut, like in the picture.
Remove the S.S. plate
(cod.0800902)
Remove the suction pump
filter

20
Remove the overflow pipe
Remove from the tank by
means of a brush or cloth if
any, residual dirt.
Clean the filter drawer
Wipe with a cloth the tank
and check for any debris on
the bottom.
Clean the pump inlet filter by
means of a brush
Clean the washing reel.
Check for any debris inside.
Insert the overflow
Clean the filter tank top
Clean the reel rinse
Insert the suction pump filter