Lamp FD30-F User manual

1
Above illustration shows the combination example of folding door
FD30-FAP(Pivoted folding).

FD30-F FOLDING DOOR SYSTEM
Installation Manual (Additional Door)
Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct
installation. Please keep this manual at hand for future reference.
●This product is parts set for pivot door system for indoor use.
●Easy door installation andadjustment.
Max.Door width 450 mm
Max.Door height 2400 mm
Min.Door thickness 28 mm
Max.Door weight 15 kg / door
Height adjustable range +3 mm
WARNING: If these warnings are not followed, it may result in death or serious injury.
Caution: If these cautions are not followed, it may result in injury or damage.
This (folding door system) should be installed by an experienced person who has correct knowledge. If the system is not
installed correctly, the door will not operate smoothly, and or may cause injury.
,WLVQHFHVVDU\WRPDQXIDFWXUHWKHIUDPHZLWKVXI¿FLHQWVWUHQJWKVRLWHQGXUHVWKHZHLJKWRIWKHGRRUDQGLPSDFWVKRFNV
upon opening/closing the door. A frame with poor strength might result in improper and slower movement of the door. In
the worst case, the door might drop down and cause injury.
Do not try to use this product for any other purposes other than originally intended for. Do not use the parts for applications
WKDWDUHRXWRIVSHFL¿FDWLRQ
Do not disassemble nor modify any parts than those described in this document.
0DNHVXUHWRIROORZWKHGHVLJQDWHGPHDVXUHPHQWVDQGVSHFL¿FDWLRQVDVZHOODVKRUL]RQWDODQGYHUWLFDOVDQJOHV0DNHVXUH
that the frame is not warped, since it may affect the movement of the door.
If cutting any parts, make sure to remove any burr before installation. Also check the upper track for any left-over burr or
scrap and remove these.
This foldingGRRUV\VWHPLVDSDUWIRUIXUQLWXUH¿WWLQJV$IWHULQVWDOODWLRQPDNHVXUHWRWHVWWKH¿QLVKHGSURGXFWWKRURXJKO\WR
ensure that it is well-functioning and safe.
0DNHVXUHWRWHVWWKHVFUHZVIRUVODFNDWUHJXODULQWHUYDOVRQHPRQWKIURP¿UVWXVDJHKDOI\HDUDQGWKHQRQHWLPHHYHU\
year is recommended).
Do not open / close the door with excessive force as this may result in damage.
Prohibited
Warning
Caution Required
Meaning of symbols
FOR YOUR SAFE WORK AND CORRECT INSTALLATION
ABOUT THE PRODUCT
SPECIFICATION
Part No. FD30FPS

2
№ ①②③④⑤
Name Top pivot Bottom pivot Pivot bracket
(top) Pivot bracket (bottom) Magnet catch
Item No. FD30-FTP FD30-FBP FD30-FSKU FD30-FSK FD30-FMC
Item
Attached screw
――――
Countersunk head
wood screw
2.4×13
11111
№⑥ ⑦
Name Upper track
(surface mount) Upper track
(recessed mount)
Guide track
(surface mount) Guide track
(recessed mount)
Item No. FD30-TRM FD30-TRH FD30-FBRM FD30-FBRH
Item
Attached screw
Recommended screw:
countersunk head tapping screw3.5×20 Recommended screw: countersunk head tapping screw3.5×16
Use1(surface mount or recessed) Use1(surface mount or recessed)
COMPONENT PARTS
■INSTALLATION DRAWING(EXAMPLE)
Door opening (when 40 mm door thickness, 450 mm door width)
46
1.2
1.2
8
44
11
20
1.4
10.5
10
2
10 19.5
2
10
9
14〜18
9
40.1 40.1
1
24
5
3
C
D=25〜35
20
29.7 23.1
25〜35
6
7
25〜35
−0.5
+0
18.5
0
+3
0
+3
−0.5
+0
8.5
Upper track
(Surface mount)
Upper track
(Recessed)
(Height adjustment range)
Upper track
(Surface mount)
Upper track
(Recessed)
Door
thickness
C=Gap
（D=30）
30 4.0
35 5.2
40 6.5
■Magnetcatch 5installation
example of strike plate
(23)
26
12
30
5
（referense
dimension）
■Door prcessing
dimension
3
38
Φ12
Φ22
38
Φ12

3
①Top pivot
②Bottom pivot
Pivot insert jig
【1】Bottom
②Bottom pivot
Magnet catch
【2】Top
③Pivot
bracket(top)
①Top pivot
⑦Guide track
Preparing Pivot Blackets 3Assembly of Upper Track
Remove any dirt or chips
from the tracks.
Caution
5Installing Pivot Bracket (bottom)
6Installing Door
④Pivot bracket
(bottom)
Pivot side
⑧Pivot bracket
(bottom)
Hole of pivot
Pivot side
4
Door leading side
2
Be careful not to damage
the plastic part of pivots.
Caution
④Pivot
bracket
(bottom)
ASSEMBLY
Cut the track applying a reinforcer to
prevent deformation of cut section.
1Cutting Track
Assembling Parts on Door
③Pivot bracket
(top)
④Pivot bracket
(bottom)

42017.02 0770-2
 
【3】Magnet catch
Adjust the position of magnet catch, then
¿[LWZLWKVFUHZ
Close the door and adjust the position of
VWULNHSODWH7KHQ¿[LW
7Door Adjustment
Strike plate
Magnet catch
【2】Vertical adjustment
Turn the nut on bottom pivot with spanner.
【1】Adjusting inclination of door
Loosen the screws on pivot brackets (top/
bottom) to make the door vertical. Then
retighten the screws.
Fixing screw
on top Pivot
bracket
②Bottom pivot
Spanner
Fixing screw
on bottom
Pivot bracket
)LQDOFRQ¿UPDWLRQ…&RQ¿UPWKDWDOOVFUHZVDUHVHFXUHO\WLJKWHQHG$QGFRQ¿UPWKDWDOOVFUHZVDUHXVHG
without mistake.
PERIODICAL INSPECTION
・Clean inside of track.
・Check upper space and lower space of the door. If necessary, correct the space.
■TROUBLESHOOTING
Trouble Check Solution
Abnormal noise during
operation Check if door touches adjacent parts. Provide necessary space between door and adjacent objects.
Check inside of upper track for foreign matter or
aluminum dust. Remove dust or foreign matter.
Check upper upper track rollers for aluminum
dust. Remove the track and pull out the roller. Then, clean the roller.
Check for loose screws retaining the upper track. Tighten the screw.
Heavy door operation 'RRUERWWRPWRXFKHVWKHÀRRU Confirm that screws on the tracks are not loosened. And, adjust door height.
$GMXVWWKHFOHDUDQFHEHWZHHQGRRUERWWRPDQGÀRRUWRPP
(20mm：Surface mount type guide track)
Check if door touches adjacent parts. Correct door position to avoid contact to other objects.
Adjust position of lower guide or stopper.
Check if door is warped. Use the door without warp.
Door starts to move. &KHFNLIWKHXSSHUWUDFNLVVHWKRUL]RQWDOO\ 8VLQJDOHYHOJDXJHUHVHWXSSHUWUDFNKRUL]RQWDOO\