Laserworld CS-400G User manual

CS-400G
User Manual
Please read this manual carefully before use!
Contents
SAFETY INSTRUCTIONS .........................................................................................................2
OPERATING THE LASER .........................................................................................................2
Using the laser.......................................................................................................................... 3
Control panel ............................................................................................................................3
Operating modes......................................................................................................................3
IL A mode ................................................................................................................................3
MX mode.................................................................................................................................4
Maintenance / cleaning ...........................................................................................................4
Technical specifications...........................................................................................................5
Trouble shooting ......................................................................................................................5
Please note................................................................................................................................5
EU-declaration of conformity..................................................................................................6

User manual: CS-400G
Rev: 02/2009
page
2
of
6
Checking parts
Please check if all listed parts are included, and are not damaged.
1 x CS-400G laser
1 x power cable
1 x remote connector
2 x key
1 x manual
S FETY INSTRUCTIONS
If the device has been exposed to great temperature changes,
do not switch it on immediately. Condensation water may
damage your device. Leave the device switched off until it has reached room temperature.
The laser must only be used for shows. Any operation has to be attended and supervised by
a skilled and well-trained operator.
Never leave this device running unattended and keep it away from children and unauthorized
persons.
Keep away from heaters and other heat sources. In order to safeguard sufficient ventilation,
leave 50 cm of free space around the device.
Never direct the laser beam to people or animals.
CAUTION LASER IO E: on’t open the housing!
There are no serviceable parts inside the device. Maintenance and service operations shall
only be carried out by authorized dealers. If you open the device for cleaning, always
disconnect from mains!
HE LTH H Z RD! Never look directly into the light source, as sensitive
persons may suffer an epileptic shock!
These lasers are considered a definite eye hazard, particularly at the higher power levels,
which WILL cause eye damage. So these laser series models supplied with a key switch to
prevent unauthorized use, warning labels and aperture labels affixed to the laser.
Installation safety
Prior to installation and operation of the laser, the paths of the beams and effects should be
considered, particularly with respect to how they will reach the audience. If direct audience
scanning is desired, then the laser energy in the effects needs to be considered to decide if
the effects are safe for direct viewing.
OPER TING THE L SER
The operator has to make sure that laser radiation – also reflected laser radiation – higher
than the maximum permissible level is avoided by technical or organisational measures.
Make sure to use the correct voltage
If the device is used in a flying installation, the mounting brackets and an appropriate safety-
rope must be fixed.
In some countries, the operator must notify the accidence insurance and the authority for
industrial safety, before operating a laser. For more information, contact the relevant
authorities.
Please consider that unauthorized modifications on the device are strictly forbidden due to
safety reasons!
If this device will be operated in any way differently than described in this manual, the
product may suffer damages and the guarantee becomes void. Furthermore, any other
operation may lead to dangers like short-circuit, burns, electric shock, etc.
Keep surrounding dry and clean. This unit should be kept dry, do not use in the rain or damp
and dusty environment. Projector should be put in a water-proof housing when operated
outside.

User manual: CS-400G
Rev: 02/2009
page
3
of
6
Operating temperature is 10~35°C. Let laser cool off 10minutes after 2 hours of operation,
to ensure maximum lifetime for the diode.
istance between laser aperture and projection screen should be not less than 1 meter.
o not turn device on and immediately off again frequently.
o not look into the laser beam directly, especially not with optical instruments.
o not touch the device with wet hands.
When the laser diode becomes dim or broken, please contact your dealer timely.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed every 15-day period. Use a sponge with alcohol, rather
than wet cloth or other chemical liquid, to clean the mirror.
Using the laser
Make sure the correct voltage is used. Connect mains. Connect an emergency switch to the
remote connector on the backside. Turn key switch to on position. epending on the mode
selected (see below), laser light should come out of the opening on the front panel – be
careful.
Control panel
Operating modes
The following operating modes can be selected from the IP switch on the backside of the
device:
IP switch 1-10 Mode
1,0,0,0,0,0,0,0,1,0 Music active, beam effects
0,1,0,0,0,0,0,0,1,0 Music active, animations
1,0,0,0,0,0,0,0,0,0 Automatic mode / beam effects
0,1,0,0,0,0,0,0,0,0 Automatic mode / animations
x,x,x,x,x,x,x,x,x,1 MX
“Music activ”: patterns are changed/animated to the beat of the music. Sensitivity can be
adjusted with the knob on the back of the device.
“ utomatic mode”: patterns are changed automatically
“DMX“: MX512 Modus-. Use the first 9 switches to select the address:
X x x x x x x x x
1 2 4 8 16 32 64 128 256
e.g. 1000 0000 01, MX mode address 1 (1+0+0+0+0+0+0+0+0+0)
0010 0100 01, MX mode address 36 (0+0+4+0+0+32+0+0+0)
ILD mode
When an IL A compatible interface is connected to the laser, the laser is automatically
switched to IL A mode. Output is then controlled from a PC running software.
1 Safety switch: laser on/off
2 Remotelock: connect emergency switch. If
no emergency switch is connected use the
9 pin plug supplied.
3 IP switch: MX address/mode selection
(see below)
4 MX 512 in/out
5 Music mode: sensitivity
6 Microphone

User manual: CS-400G
Rev: 02/2009
page
4
of
6
DMX mode
Maintenance / cleaning
Always disconnect from mains before cleaning/opening the laser. Regularly clean the interior
from dust, especially ensure operation of the fans. Use a sponge with alcohol, rather than
wet cloth or other chemical liquid, to clean the mirrors. Be careful, even light scratches
reduce the output power of the laser. Mirrors need cleaning, when a “halo” is noticeable
around the beam, or an unusual high amount of diffuse light can be seen inside the device.
CHANNEL VALUE 0~255 CONTROL CONTENT
0~30 Laser source turn off
31~61 MX geometric pattern model
62~92 MX geometric SHOW editing model
93~123 MX geometric SHOW automatic model
geometric pattern
page
124~154 MX geometric SHOW music control model
155~185 MX animation patterns model
186~216 MX animation SHOW editing model
217~247 MX animation SHOW automatic model
CH1
animation
patterns page
248~255 MX animation SHOW music control model
1~255 Pattern model: pattern A selection CH2 Multiple channel
0~255
SHOW
model

laser SHOW selection
1~255 Pattern model: pattern B selection CH3 Multiple channel
0~255 SHOW model laser SHOW part selection
CH4 pattern C
selection
1~255 Pattern model: pattern C selection
CH5 pattern selection
1~255 Pattern model: pattern selection
0~51 A,B,C, pattern be controlled simultaneou
52~103 Pattern A control effect
104~155 Pattern B control effect
156~207 Pattern C control effect
208~255 Pattern control effect
0 is the turn-off laser SHOW part editing function
CH6 Multiple channel
0~255 1~255is the turn-
on laser SHOW part editing
function
1~127 Angel rotating selection, 15CH speed adjustment
128~191 anticlockwise
CH7 Rotation effect
192~255 clockwise
1~127 Vertical rotation linearity adjustment, 15CH speed
adjustment
CH8 Vertical reversal
effect
128~255 Vertical rotation speed selection
1~127 Horizontal rotationlinearity selection, 15CH speed
adjustment
CH9 Horizontal
reversal effect
128~255 Horizontal rotation speed selection
1~127 Horizontal moving speed selection CH10 Moving effect
128~255 Vertical moving speed selection
0~41 gradual increasing drawing
42~83 gradual decreasing drawing
Gradual drawing
effect 84~127 gradual increasing and decreasing drawing CH11
ot effect 128~255 Adjustment of point brightness
CH12 Vertical postion 1~255 Vertical position adjustment
CH13 Horizontal 1~255 Horizontal position adjustment
15CH speed adjustment
1~127 Adjustment of pattern size
15CH speed adjustment
128~169 Pattern from small to big
15CH speed adjustment
170~211 Pattern from big to small,
15CH adjustment speed
CH14 Zoom in/out
effect
212~255 Zoom patterns 15CH speed adjustment
CH15 Speed adjustment
0~255 CH11, CH12, CH13, CH14 show speed adjustment

User manual: CS-400G
Rev: 02/2009
page
5
of
6
Technical specifications
• Lasersources: aircooled PSS Laser
• Power (of the diodes): typical 400mW, minimum 300mW 532nm green
• Laserclass: 3b
• Modes: IL A, MX 512, auto, music active
• ILD : 25pin IL A standard Sub- shaped 25pin connector
• Galvos: 25k scanspeed
• DMX 512: 15 channels
• Patterns: 85 + 43 animations
• Scanangle: ca. 40°
• Beam: ca. 3mm/1mrad
• ccessories: power cable, key switch, interlock connector, manual
• Input voltage: AC 220~240V 50/60Hz
• Power consumption: 50W
• Size: 300 x 300 x 150mm (W x x H)
• Weight: 5kg
• Operating temperature: 10°-35°C
Trouble shooting
No beam: emergency switch/dongle not connected.
Low output: clean mirrors/window
Musicmode not working: wrong IP switch setting
Sensitivity too low
No MX control: wrong IP switch setting
IL A connected
Laser does not switch to IL A mode:
•The interface does not connect pins 4 and 17 (Interlock) of the I LA signal. See interface
manual
•The cable does not connect pins 4 and 17. Use a cable that connects pins 4 and 17.
•Use an adapter that connects pins 4 and 17.
Please note
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and
unskilled operation!

User manual: CS-400G
Rev: 02/2009
page
6
of
6
EU-declaration of conformity
We hereby confirm that the following device
Laserworld CS-400G
complies with the essential safety requirements, laid down in the regulations of the
committee to assimilate the provisions of law of all participating EU states on the
electromagnetic compatibility (89/336/EWG).
The device has been classified considering the following EU-norms on
electromagnetic compatibility:
IN EN 61000-3-2:2000 + A2: 2005
IN EN 61000-3-3:1995 + A1: 2001
Assessment of compliance of the product with the requirements relating to the Low Voltage
irective (LV 2006/95/EG) was based on the following standards:
IN EN 60065 : 2002
Furthermore, the device is verified in correspondence to the laser class regulations IN EN
60825-1, if properly set up according to the upper mentioned laser safety regulation.
After installing the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the european guidelines EN 60825-1 and corresponding
regulations for the prevention of accidents BGV-B2.
This declaration is executed on behalf of the Laserworld CS-400G manufacture
Laserworld (Switzerland) G
Oberstrasse 1
8274 Tägerwilen
SWITZERLAN
Authorized person:
Supervisory board Ms Rhea Gössel
place of business: 8274 Tägerwilen / SWITZERLAN
company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
www.laserworld.com
[e-mail]
representative according to EMVG:
Cleantech Europe GmbH
Managing irector: Thomas Schulze
Fürkhofstr. 5
81927 München / E