Laserworld PL-20.000RGB CT User manual

Manual
PS-29.000RGB CT
PL-20.000RGB CT, PL-42.000RGB CT,
PL-20.000G CT
Please read this manual carefully prior to product operation!
rev. 10/2012 ns

Manual: Pure Sapphire / Purelight high power
page 2 / 8
Legal notice:
Laserworld AG reserves the right to make modications to its products, attending to further
technical developments. These modications do not necessarily have to be recorded in each
case.
This manual and its information have been made with due care. Laserworld AG cannot, howe-
ver, take any responsibility for errata, bugs, or the resulting damages.
The brands and product names mentioned in this manual are trade marks or registered trade
marks of their respective owners.
Content:
1. Scope of delivery & details
2. Preliminary warning notices
3. Steps for setup, safety instructions
4. Safety instructions for work on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
Final statement
Technical data sheet
Laser specications

Manual: Pure Sapphire / Purelight high power
page 3 / 8
1. Scope of delivery & details
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x power cable
1 x manual
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see in-
formation on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualied persons ac-
cording to safety regulations of the res-
pective country.
4. Always ensure that maximum permissib-
le exposure (MPE) is not exceeded in are-
as accessible to the public.
5. In some countries an additional ins-
pection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
7. The power supply should be easily acces-
sible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of pro-
fessional associations and/or comparable
regulations for accident prevention.
10. If the device has been exposed to great
temperature changes, do not switch
it on immediately. Condensation water
may damage device.
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of blindness!
4. Do not operate the device at a high humidity, in rain or in dusty environments.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers at the device.
Warranty claim expires with removal of warranty label.

Manual: Pure Sapphire / Purelight high power
page 4 / 8
11. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
le, do not use the laser projector together
with large appliances (especially fog ma-
chines) on the same mains!
12. Ensure sucient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degra-
dation of performance.
4. Working on the device
1. Be sure that the mains plug is not connected to the power sup-
ply while installing or opening the device (e.g. for cleaning).
2. Take o all reecting things like rings, watches etc. before
starting to work with or at the projector.
3. Only use non-reecting tools to work on device.
4. Wear protective clothing (like goggles, gloves etc.) accor-
ding to laser power and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of device can re-
duce durability of the laser diode drama-
tically.
• Avoid concussions during transport.
• To increase durability of your laser,
protect device against overheating:
-Always ensure sucient ventilation.
-Do not face spotlights (especially mo-
ving heads) to the device.
-Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with dierent temperature.
-Keep the device dry. Protect it from
moisture, rain and damp.
-Switch o device when it is not nee-
ded. Diodes are switched on and can
wear o even if there is no visible la-
ser output.
• Open the device at regular intervals and
remove any dust, particularly around fans
and laser. Otherwise the risk of overhe-
ating is imminent and will void the war-
ranty.
• If there are traces of fog uid in the pro-
jector, clean it and change the position of
the fog machine.
• As for troubleshooting, please check the
FAQ on our website www.laserworld.com

Manual: Pure Sapphire / Purelight high power
page 5 / 8
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
6. Warnings and other notices on the device
Laser radiation!
Avoid exposure
to beam.
Laser class 4
Caution of
radiation if cover
is removed power supply
& consumption
model type
wavelength
Output power
production
year
Please read manual before operation
Use in enclosed spaces only!
7. Device connections
Power connection
ILDA in
Mains switch
Key switch
ILDA in
ILDA out
Trim pots for color
balancing
Invert X / Y axis
Two-mode Scan Safety:
Switches for setting

Manual: Pure Sapphire / Purelight high power
page 6 / 8
8. Operation
1. ILDA operation mode
The laser system is controlled over ILDA control signal. Plug in the ILDA cable to the ILDA-in
interface at the unit.
2. Scan Safety
This units has a special two-mode scan safety: It can be operated in scan fail safety mode, that
prevents the occurance of dangerous radiation in case of malfunction. The beam block mode
suppresses every too focussed beam to avoid the accidential exceeding of maximum permit-
ted exposure levels for spectators. The modes can be changed by using the switches at the
control panel. The scan safety can also be switched o.
3. Color blancing
By using the trim pots for color balancing it is possible to adjust the individual color sources to
achieve a certain white balance. This is especially important if several laser systems are used
an a homogenous white is needed.
4. X/Y axis inversion
These switches invert the ILDA singal for the respective axis. This feature is useful if one ILDA
signal line is used for controlling several lasers.

Manual: Pure Sapphire / Purelight high power
page 7 / 8
Final statement
Product and package leaving warehouse without faults. Users have to follow the local safety
regulations and warnings of this manual. Damages through inappropriate use do not unterlie
the sphere of inuence of manufacturer or dealer. Therefore no liability or warranty will be
taken over. We cannot inform you in case of changes of this manual. If you have any questions,
please contact your dealer.
For service please contact your dealer or Laserworld. Please use only spare parts of Laserworld.
Subject to change without notice. Because of the vast amount of data we cannot guarantee
any correctness of given information.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil-Oberhofen
SWITZERLAND
Authorized person:
Supervisory board Mr Martin Werner
place of business: 8574 Lengwil-Oberhofen / SWITZERLAND
company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
www.laserworld.com
[email protected]
representative according to EMVG:
Cleantech Europe GmbH
Managing Director: Thomas Schulze
Fürkhofstr. 5
81927 München / GERMANY

Manual: Pure Sapphire / Purelight high power
page 8 / 8
Technical data
Laser sources: DPSS laser (green), diode (red / blue)
Laser class: 4
Scanner: CT-6215, 50kpps with two-mode scan fail safety
Scan angle: 70° max.
Operation modes: ILDA
Beam:
PS-29.000RGB CT: ca. 5.5mm / <4mrad (full angle divergence)
PL-20.000RGB CT: ca. 5.5mm / <2mrad (full angle divergence)
PL-42.000RGB CT: ca. 5.5mm / <2mrad (full angle divergence)
PL-20.000G CT: ca. 5.5mm / <2mrad (full angle divergence)
Power supply: 230V, 50Hz (+/- 5%)
Power consumption: max. 600W
Operating temperature: +10° to +35°C
Dimensions: 510 x 390 x 290 mm (L x W x H)
Weight: ca. 40kg
PL-42.000RGB CT: ca. 48kg
min. - max. Red Green (532nm) Blue (445nm)
PS-29.000RGB CT 23.900 -
29.000 mW
>3.900mW
638nm >8.000mW >12.000mW
PL-20.000RGB CT 16.000 -
20.000mW
>4.000mW
638nm >8.000mW >4.000mW
PL-42.000RGB CT 35.000 -
42.000mW
>10.000mW
638nm/658nm >15.000mW >10.000mW
PL-20.000G CT 15.000 -
20.000mW - >15.000mW -
Power specications (at laser module)