LAZBOY Woodbury Series User manual

Woodbury Series
Assembly Instructions
LZB-48961A / LZB-48961B (400 lbs)
LZB-48962A / LZB-48962B (275 lbs)
LZB-48963A / LZB-48963B (275 lbs)
Model

2
D
C
B
A
E1 E2 F
IJK
G
H
LN
Allen Key
Quantity: 1
PARTS/PIÈCES
Casters
Quantity: 5 Star Base Quantity:1 Gas Liftwith Telescoping Cover Quantity: 1 Seat Plate Quantity: 1
Left Arm
Quantity: 1
SeatCushion
Quantity:1
Back Cushion
Quantity: 1
Right Arm
Quantity: 1
D1
D2
1” Screws
Quantity: 2
1-1/2” Screws
Quantity: 2
1-1/4” Screws
Quantity: 4
M
Plastic Caps
Quantity: 4
Plastic Shroud
Quantity: 1
2-1/2” Screws with Spring Washers
Quantity: 4

3
Step 1
Place the Star Base (B) upside down and insert 5 Casters (A)
into the holes on the Star Base (B).
Step 2
Turn the Star Base (B) over and insert the Gas Lift with
Telescoping Cover (C) through the center hole on top of Star
Base (B).
B
A
B
C

4
Step 3
Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the
front of the seat plate facing the front of seat cushion). Attach by using
two 1-1/2” Screws (J) for the front holes of the Seat Plate (D) and two 1”
Screws (I) for the rear holes of the Seat Plate (D) and tighten the screws
using Allen Key (N).
*Note:Tighten thescrews completely.
Step 4
Insert Levers (D1& D2) of Seat Plate (D) to the pre-attached
cable lever receivers on the underside of Seat Cushion (F) (with
the front of levers facing the front of seat cushion). Push down the key
on the receivers to pull out the levers.
*Note:Fix the cable forthe seat plate into the plastic clips
attached to the bottom of the seat cushion.
Disassemble the lever
Assemble the lever
Insert Push
NJ
D2
I
D
D
F
F
D1

5
Step 5
Position the back support plate over the Seat Plate (D), and
attach the Back Cushion(G) to the Seat Cushion (F) with
four 1-1/4" Screws (K).
*Note: Do NOT tighten the screws completely.
Step 6
Insert four 2-1/2" Screws with Spring Washers (L) into arm
holes attaching Arms (E1 & E2) (with front of arms facing
the front of seat cushion) to sides of Seat Cushion (F) and
Back Cushion (G).
*Note: Tighten all the screws completely.
N
N
K
G
D
F
G
F
E2
E1
L
L

6
Step 7
Put the Plastic Shroud (H) over the Seat Plate (D) (with front
of plastic shroud facing the front of seat cushion). Align
shroud posts to holes on bottom of Seat Cushion (F) and
press into position.
Step 8
Position the assembled chair upright with the seat plate
facing down. Insert the Gas Lift with Telescoping Cover (C)
into the center hole of the Seat Plate (D).
F
H
F
D
C
D

7
Step 9
Press the Plastic Caps (M) into the holes on outside of the
arms once all screws have been tightened.
M
M

8
Operating Instructions
Function Instruction - 1
To Adjust Seat Height:
While seated, lean forward and reach under the right side of the
chair to find the lever. Lift the lever and raise your body up slightly
to allow the chair to rise to the desired height. Once desired height
is reached, release lever to lock chair at desired height. To lower the
seat, lift the lever while seated. The chair will descend until the lever
is released or the chair reaches the bottom position.

Function Instruction - 2
To Operate Tilt Lockout:
While seated, reach under the left side of the chair to find the
lever. Push down the lever and lean back to allow the chair to tilt
backwards. To lock the chair in the upright or vertical position, sit
upright and pull the lever to the up position.
9

10
Function Instruction - 3
To Adjust Tension On The Tilt:
Reach under the front center of the chair, grasp the round knob
(R) and turn it counter- clockwise to stiffen the tilt mechanism for
a heavier user.Turn the knob (R) clockwise to loosen the tilt
mechanism fora lighter user. Rotate the knob (R) until the desired
resistance is reached.
R