LDR Arpa 8/22 150 W LED, 3200K User manual

01154020
01154120
01154030
01154130
01154040
01154140
Arpa8/22150WLED,3200K
Arpa8/22150CLED,5600K
Arpa18/36WLED,3200K
istruzioniperl'uso
operatinginstructions
Bedienungsanleitung
instruccionesdemanejo
moded'emploi
gebruiksaanwijzing
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredomnItaly.tel+390376771777‐fax+390376772140‐email[email protected]
Arpa18/36CLED,5600K
Arpa 30/55 W LED, 3200K
Arpa 30/55 C LED, 5600K
DMX512 +RDM

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
1
ENGLISH–TABLEOFCONTENTS

INTRODUCTION
1.Importantsafetynorms...........................................................................2
2.Boxcontents………………………………………………………………….…………………….3
3.Weightanddimensions...........................................................................4
4.Mounting/replacingtheirisdiaphragm–notsupplied……………………….4
5.Mounting/replacingthegobo‐holder–notsupplied…………………………..4
6.Importantnoticebeforetheinstallation/installation……………………….…4
7.Wiring………………………………………………………………………………………………….5
8.Voltage……………………………………………………………………………………………….6
9.Frequency................................................................................................6
10.Mechanicaloperation………………………………………………………………………..6
11.Connecttothepowersupply…………………………………………………………….7
12.Localcontrolpanelandoperation………………………………………………….....7
CONTROLANDOPERATION
13.Menu…………………...................................................................................7
13.1DMXormanual....................................................................................7
13.2DMXaddress........................................................................................8
13.3Dimmerresolution...............................................................................8
13.4LostDMXsignal....................................................................................8
13.5Strobe..................................................................................................8
13.6Strobespeed........................................................................................8
13.7Dimmingcurve.....................................................................................9
13.8Cutoffdimmingresponse...................................................................9
13.9Dimmingbehaviour...........................................................................9
13.10FanSetting........................................................................................9
13.11LCDscreenillumination..................................................................10
13.12Temperaturecontrol.......................................................................10
13.13Softwareversion..............................................................................10
13.14PRO–BASICcontrol........................................................................10
13.15Factorysettings...............................................................................10
13.16IDforREMOTO................................................................................10
13.17Calibration.......................................................................................11
13.18Exithiddenmenu............................................................................11
14.Cleaningandmaintenance..................................................................11
15.Spareparts...........................................................................................11
16.Warranty..............................................................................................11
SUMMARYOFCONTROLSANDOPERATION
17.SummaryoftheALBAfunctions
..........................................................12
18.DMXCharts..........................................................................................13
18.1DMXChart1.......................................................................................13
18.2DMXChart2.......................................................................................13
18.3DMXChart3.......................................................................................14
18.4DMXChart4.......................................................................................15

LDRConformityCertificate–CertificatodiConformità–Konformitätserklärung page16
Complaintform–Modulodireclamo–Reklamationsformular………………………….page17
WEEEDirective–DirettivaRAEE–WEEERichtlinie……………………………………………page18

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
2
ENGLISH
ThankyouforchoosingaqualityproductfromLucidellaRibaltasrl.Wetrustourproductsandservices
meetyourrequirements,butshouldthisnotbethecasepleasecontactusdirectlyusingtheattached
feedbackformtohelpusimprovethequalityofourservice.
Thisproducthasbeenmanufacturedwithgreatcareandleftourfactoryinperfectconditions,butifit
hasbeendamagedintransportpleasecontactyourdealerinthefirstinstance.Afeedbackformis
appended.Ourwarrantycoversallmanufacturingandcomponentdefectsfor2yearsfromthedateyou
receivedtheproduct.
Ourproductsaredesignedfortheuseofprofessionaltechnicians,andtheinstructionsprovidedhere
ensureasafeandcorrectoperationofthisproduct.LucidellaRibaltasrlwillnotacceptanyresponsibility
wheredamagehasbeencausedtotheproductorpersonsthroughimproperuseoftheproductand/or
non‐compliancewiththeregulationsdescribedherein.
IMPORTANT:Readtheseuserinstructionsbeforeusingthislightingunit
Theinstructionsgivenhereensureasafeandcorrectusageofthisproduct.Auser’sfailuretocomply
withtheinstallation,operating,maintenanceandsafetyproceduresmentionedinthismanual,aswellas
thosegenerallyapplicabletothislightingequipment,maycausetheluminairenottoperformas
expected.
LucidellaRibaltaacceptsnoliabilityfordirect,indirect,incidental,special,orconsequentialdamages
resultingfromthecustomer’sfailuretofollowtheinstallation,operating,maintenanceandsafety
proceduresinthismanualorthosegenerallyapplicabletolightingequipments.
Thelimitationextendstodamagesforpersonalinjury,propertydamage,lossofoperations,lossof
profits,lossofproductorlossoftime,whetherincurredinbythecustomer,thecustomer’semployeesor
athirdparty.
Apartfromtheinstructionsgivenonthismanual,allrelevantsafetyandhealthstandardsofthe
appropriateEUDirectivesorthelocalsafetymustbecompliedwith.

1. IMPORTANTSAFETYNORMS
Thisproductisaprofessionallightingfixture,namelyaprofilespot,fittedwithaLEDlightsource,
whichcanonlybeoperatedbyprofessionalstaff
Thisproductmustbefittedwithasecondaryfixingsystemsuchasasafetychainorbond.Should
thisnotbesuppliedasastandardaccessory,pleasemakesureyoubuyitseparatelyandinstallit
beforeusingtheproduct
Warning,highvoltageignition.Disconnecttheunitfrompowerbeforeservicing
Continuousmainspowerisrequiredforthisspotlightasaninternaldimmercontrolstheintensity
viaDMXorlocalrotaryknob.
Useofaphasecontroldimmedmainssupplymaydamagetheinternalelectronics
Thisproductfeaturesfan‐assistedventilation.Makesureyoudonotcoverthefansorobstruct
theairflowatanytime
Makesureallfansareworkingcorrectlyatanyonetime.Shouldyoudetecteventheslightest
malfunction,switchtheluminaireoffandcarryoutthenecessaryservicing.Replacethefansif
necessary.
ThisproductisratedIP20andisthereforedesignedforinterioruseonly.Fordetailsonmaximum
ambienttemperatureandtiltanglepleaserefertowhatindicatedontheproductlabelorscreen‐
printingonthesideofthelens‐tubeortherearoftheLED‐house
Repairingandreplacementofanycomponentofthisproductmustbecarriedoutexclusivelyby
professionalpersonnelinconformitywiththerelevantsafetyandhealthstandardsandonlywith
originalLucidellaRibaltasrlcomponents.

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
3
Replacementofanypartofthewiringsystemmustbecarriedoutexclusivelybyprofessional
personnelincompliancewiththeoriginalwiringdiagramandwithcomponentsidenticaltoor
compatiblewiththoseoriginallyfitted.
Installationofthisproductmustbeexclusivelycarriedoutbyprofessionalpersonnelin
compliancewiththesafetynormsinforceinthecountrywheretheproductisused




WARNING:DANGEROFELECTRICALSHOCK
DONOTOPERATEONLIVEEQUIPMENT
Disconnectpowerbeforeopeningthisfixturetoaccessitslightsourceorelectronics.
ThereplacementoftheLEDsourceoranyofitselectroniccomponentscanbecarriedout
exclusivelybyprofessionalpersonneluponLDR’swrittenauthorizationandonlywithoriginalLuci
dellaRibaltasrlcomponents.Failuretoobtainthemanufacturer’sauthorizationtocarryoutthe
replacement/repair,willimmediatelyinvalidatetheproduct’swarranty




WARNING:EYEDAMAGEHAZARD
Makesurethisfixtureisinstalledsoastoavoidprolongeddirectstaringatitsoperatinglightsource
(LED)fromadistanceoflessthan7m/23ft.




WARNING:FIREHAZARD
Neverlocatethisfixtureonanyflammablesurface.
Minimumdistanceofanypartofthebodyoftheluminairefromanyflammablesurfaceorobject:
0,5m/20in
Minimumdistancefromlitsurface,pleaserefertoproductlabel
Makesurethemainspowersupplythefixturewillbeconnectedtoisprotectedbyasuitable
thermalmagneticcircuitbreaker



2.BOXCONTENTS
Uponopeningthepackaging,pleasemakesureitcontainsthefollowing:
lightingunitinthechosenmodel
metalcolourframe185x185mm,fitted
4metalshutterblades

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
4
2m/6.5ftmainspowercablefittedwithNeutrikPower‐Conblueconnector

Shouldoneormoreitemsmiss,wekindlyaskyoutocontactyourdealerimmediately.


3.WEIGHTANDDIMENSIONS
 

Arpa8/22150WLEDprofile Arpa18/36150WLEDprofileArpa30/55150WLEDprofile
netweight:16,4kg  netweight:15,6kg  netweight:14,2kg
grossweight:20,0kg  grossweight:17,5kg  grossweight:17,2kg
packing:100x41x41hcm packing;83x41x41hcm packing:73x41x41hcm


4. MOUNTING/REPLACINGTHEIRISDIAPHRAGM–A20100707notsupplied
Anirisdiaphragm,availableasseparateaccessoryunderpart#A20100707,andfeaturing20leaves,
allowstosizethebeamfromamaximumapertureof68mm/2.67intoaminimumof5mm/0.19in.

Inordertofitorreplacetheirisdiaphragmplease:

UsingaPhillipsscrew‐driverremovethetwocross‐headscrewsfromthesidesoftheirisplate.
Slidethediaphragminthegatearea.
Tightenthescrews.


5. MOUNTING/REPLACINGTHEGOBO‐HOLDER–notsupplied
Albaprofilespotscanbefittedwithagoboholder–notsuppliedinstandarddeliverybutobtainableasa
separateaccessory,fortheprojectionof:

A‐orB‐sizemetalgobospart#A20100807
A‐sizeglassgobo part#A20100807/A
B‐sizeglassgobo part#A20100807/B

Thegoboholdermustbeinsertedinthegateareainsteadoftheirisdiaphragm.Usageofboth
accessoriesatthesametimeisnotpossible.

Inordertofitorreplaceagoboholder,please:

Removetheirisdiaphragmiffitted(seeabove)
Slidethegobo‐holderinthegatearea–bentmetalwingsmustlooktotheLED‐house
Makesureitiscorrectlypositionedandapplypressuretotheplasticholderifneeded

CAUTION:themetalsurfaceofthegoboholderreachesveryhightemperaturesduringoperation.
Makesuretheunitistotallycoldbeforeattemptingtoremoveit,protectyouhandswithgloves
andavoidskindirectcontactwithitsmetalsurface


6. IMPORTANTNOTICEBEFORETHEINSTALLATION/INSTALLATION
Beforeinstallingthisfixturecheckitsweightontheproductlabelandtheweightofeachaccessoryyou
areaddingandmakesurethestructureyouareinstallingittowithstandsthetotalweight.

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
5

Themountingstirrupismountedontherearupperprofilesofthelens‐tubeandisdesignedtoallowthe
spotlighttobesuspendedfromaboveusingaC‐clampwithM12screworaDINplate

CAUTION
DONOTTURNTHELUMINAIREUPSIDE‐DOWNBUTALWAYSTURNTHESTIRRUP
IFYOUNEEDTOMOUNTITONASTANDORBRACKET

AsthestirrupdoesnotrotatearoundtheLED‐house,incaseyouneedtomounttheluminaireonastand
orbracketyouwillhavetoremovethestirrupfromitsoriginalpositionandre‐mountitonthesetsof
holes(2xoneachside)positionedontherearlowerprofilesofthelenstube,asfollows.
PositiontheAlbaonasolidandstablework‐bench
WiththeaidofaM5cross‐headscrew‐driverslackenandremoveallthe4screwsholdingthe
stirruptothelens‐tube
Liftthestirrupandre‐positionthescrews
Removethe4xM5screwsfromthelowersetsofholes
Positionthestirruponthe4xholes,makingsureitsbendlookstothefrontoftheluminaire
Stronglytightenthe4screws

Ifnotsuppliedchooseasuitableclamporspigotandmakesureitiscorrectlyfixedandstrongly
tightenedtothestirrupaccordingtotheclamp’s/spigotmanufacturer’sinstructions
Ifnotsuppliedchooseasuitablesafetycableorbond.Clampittotheeyeletprovidedontheupper
rearpartoftheluminaire(seepictureherebelow),runittwicearoundthestirrupandthestructure
theluminaireishungtosoastobondthemtogetherandclosetheloop.



Whentiltingtheunitmakesuretheknobblockingthestirrupisstronglytightenedatanytimeand
thattheluminairecanholdthedesiredtiltangle

7.WIRING

Beforebeingconnectedtothemainspower,thisunitmayneedtobewiredwithasuitableplugifnot
alreadyinstalled.Makesuretheplugyouareusingisratedfortheproperpowerloadanditconformsto
therelevantEU/ULelectricalstandards.

Makesuretheplugyouarefittingwithstandsthelamppowerload.
Thisfixturemustbegrounded
Toperformacorrectwiring,pleasenotethatthecoresinthismainsleadarecolour‐codedas
follows:
Ground:green+yellow–Neutral:blue‐Phase:brown


Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
6
Incasethecoloursofthewiresdonotcorrespondtothecolouroftheconnectionpointsonyourplug,
pleaseproceedasfollows:
Thegreenorgreenandyellowwiremustbeconnectedtotheconnectionpointmarkedwiththe
letterEorwiththesymbol orcolouredingreenoringreen‐yellow
ThebluewiremustbeconnectedtotheconnectionpointmarkedwiththeletterNorcolouredin
black
ThebrownwiremustbeconnectedtotheconnectionpointmarkedwiththeletterLorcoloured
inred
Beforeyoufinallypositionthisproductforuse,temporarilyconnectittoaproperlyfusedpower
supplytocheckthelampworkscorrectly.


8. VOLTAGE

Beforeoperatingthisunitpleaserefertotheproductlabelmountedatthebackoftheluminairetocheck
youareoperatingwiththecorrectvoltage.
TheAlbaprofilecanbeoperatedbetween90Vand260VandtheelectronicPSUinsidethefixturewill
automaticallyswitchtotheavailablevoltage.


9. FREQUENCY

FrequencyonthisproductisautomaticallyselectedbytheelectronicPSU(50/60Hz)

10.MECHANICALOPERATION
Installation:thisfixtureisfittedwithamountingstirrupwhichisfactory‐setfortheinstallationfrom
above(suspended)usingaC‐clamporsimilar.Incaseyouneedtoinstallthefixtureonatripodor
support,(seeaboveforreference)
Note:thespotlight’slocationmustprovidesuitableventilationfortheLEDmodule.Forminimum
distancefromflammableandlitsurfacepleaserefertotheFIREHAZARDsectioninthismanualortothe
product’slabel
Focuscontrol:theARPArangeofLEDprofilespotsisavailablein3variablebeamanglemodels,including
8°to22°,18°to36°and30°to55°.Twolarge,easy‐to‐grabcontrolknobsontheright‐handsideofthe
lens‐tubecontrolthefocus.
Thevariablebeamismodifiedbyadjustingthefrontandrearzoomlensesinrelationtoeachother.
Thefrontlensdefinesthebeamspread,therearlensdefinesthefocusdegreeof‘softness’or‘hardness’
ofthebeamedgeorshutters.
Thebeamdistribution(peak/flat)isfixed.
Gentlyturntheknobsanti‐clockwiseuntilyouhavereachedthedesiredsize/focusofthebeamin
relationtothedistanceyouareprojectingat.
Turntheknobsclockwiseandtightlyclosethemsothatthelensesareheldinpositionatanytiltangle
Beam‐shaping:4shutterbladesareprovidedwitheachfixturetoshapethebeamgeometrically
Beam‐sizing:anaccessoryirisdiaphragm,part#A20100707canbepurchasedseparatelyandusedto
sizethebeamoftheARPA
Tiltcontrol:Thestirrupisfactory‐balancedandfittedwithapositivefrictionclampcontrolledbyauser‐
friendly,effectivelever‐knob.Turntheleveranticlockwisetoreleaseit,positiontheprofileatthedesired
tiltangleandturntheleverclockwisetoholdthedesiredposition.
Pressthebuttonatthetopoftheleverandkeepitpressedwhileturningtheleverifyouneedtochange
itsposition.

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
7
Makesuretheleverisstronglytightenedatanytimeduringoperation

11. CONNECTTOTHEPOWERSUPPLY
Connecttheunittoacontinuousmainspowersource
Makesurethepowersupplyisprotectedbyasuitablethermalmagneticcircuitbreaker
Thisfixturemustbegrounded

12. LOCALCONTROLPANELANDOPERATION

OPERATION:LCDdisplayforDMXaddress,systemsetupandstatusdetails.
POWER:powerLEDstatusindicator,redcolor.ON=power
DMX:DMXLEDstatusindicator,greencolor.LEDOFF=DMXOFFandmanualcontrolactivated,
LEDON=DMXMODEactivatedwithnoDMXsignal,FLASHINGLED=receivingDMX
MENU:rotaryswitchselectortoselectandmodifytheoperationalmodes.Turnleftorrighttonavigate
throughthemenuandpresstoselectortoconfirm
DMXIN:inputDMXsignal(pin1=0,pin2=DATA‐,pin3=DATA+).
DMXOUT:LoopthroughDMXsignaloutput
POWERIN:Mainspowerinput
POWEROUT:Mainspoweroutput

13. MENU

TherearethirteendifferentmenustocontrolthesettingsoftheARPALED.Therotaryselectorisusedto
adjustthesettingsandtonavigatethroughthemenu.Turnleftorrighttoselectthemenuandpushto
accessortoconfirmtheselecteddataorfunctions.Toexittheselectedmenuswithoutsavingthedata,
presstherotaryselectorforatleast1second.


13.1DMXORMANUAL(Mode)
SelecttheLEDcontrolmodebetweenDMX(factorysetting)andmanual.Tochangethecontrolmode
pressoncetherotaryselectoruntilanarrow()appearsonthemenu.Turntheselectortotherightor
thelefttoselectthedesiredmodeofoperationandpresstoconfirmyourselection.




TaptherotaryselectorandtheLCDscreenwilldisplaythemodestatusandthecurrentvalue:












M: Manual
XX % XXX
M: DMX
XX %
1 Mode
DMX
1 Mode
MANUAL
TAPTHEROTARY
SELECTORTODISPLAY
THEVALUE
TAPTHEROTARY
SELECTORTODISPLAY
THEVALUE
00%=LEDOFF
100%=LEDFULL
00%(000)=LEDOFF
100%(FFF)=LEDFULL
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
1 Mode
DMX
1 Mode
DMX 
1 Mode
MANUAL 
TURNTOSELECT
MANUALORDMX
ANDPRESSTO
CONFIRM

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[email protected]–webwww.ldr.it
8
13.2 DMXADDRESS(Addr)
ItallowstoselecttheinitialDMXstartingaddresstoremotelycontroltheLEDfunctions.Tochangethe
initialDMXaddresspresstherotaryswitchuntilanarrowappears,thenturntochangetothedesired
DMXstartingaddress.Presstoconfirmyourselection.Factorysettingis001.




13.3 DIMMERRESOLUTION(8/16b)
Thedimmingresolutioncanbecontrolledat8bitsfromoneDMXchannelor16bitswith2DMX
channels.Factorysettingis8Bit.





13.4 LOSTDMXSIGNAL(DMXMem)
IncaseofsignalfailurethisfunctionallowstostoreinmemorythelastDMXvalue.FactorysettingisON.
Threeoptionsareavailable:











13.5 STROBE(Strobe)
Thisfunctionenablestoactivatethestrobefunction.FactorysettingisDISABLE.




13.6 STROBESPEED(SetStr)
Itallowstosetthestrobespeed.Thismenuisnotactivewhenthestrobefunctionisdisabledorwhenit
isremotelycontrolledthroughDMX.FactorysettingisOPEN.











2 Addr
001
2 Addr
001 
2 Addr
### 
TURNTOASSIGNTHE
DMXADDRESSAND
PRESSTOCONFIRM
3 8/16b
8 BITS
PRESSTHEROTARY
SELECTORTO
ACTIVATE
3 8/16b
8 BITS 
3 8/16b
16 BITS 
TURNTOSELECT8OR
16BITSANDPRESSTO
CONFIRM
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
4 DMXMem
ON
5 Strobe
DISABLE
5 Strobe
DISABLE 
5 Strobe
ENABLE 
TURNTOENABLEOR
DISABLESTROBEAND
PRESSTOCONFIRM
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
6 SetStr
OPEN
WITHSTROBEENABLE
THELIGHTISSETTOON
6 SetStr
OPEN 
6 SetStr
SPEED # 
CHOOSETHESTROBE
SPEEDVALUEFROM
1(SLOW)TO10(FAST)
6 SetStr
CLOSED 
WITHSTROBEENABLE
THELIGHTISSETTO
OFF
LASTSCENEHOLD
4 DMXMem
ON 
4 DMXMem
OFF=80% 
DIMTHELEDTO80%OF
ITSMAXIMUMPOWER
4 DMXMem
OFF=00% 
DIMTHELEDTO0%

Arpa8/22,18/36and30/55150WLEDUser’sManual–2.0
LucidellaRibaltasrl,ViaBerna14,46042CastelGoffredo(MN)Italy
Tel.+390376771777–fax+390376772140–email[e-mail]–webwww.ldr.it
9
13.7 DIMMINGCURVE(Curves)
ThisfunctionallowstoselectaresponsecurvefortheARPALED.Achoiceoftwocurvesisavailable:
SquareandLinear.FactoringsettingisSQUARE.







13.8 CUTOFFDIMMINGRESPONSE(CutOff)
ThisfunctionallowstoselecttheLEDbehavioursimulatingatungstenorhalogenlampduringthe
dimmingcutoff.
FactorysettingisSLOW.







13.9 DIMMINGBEHAVIOUR(Smooth)
ThisfunctionallowstosettheLEDdimmingresponse.FactorysettingisNORMAL.










13.10FANSETTING(Fan)
Thisfunctionallowstosetthefanresponse.Achoiceofthreemodesisavailable:Automatic,Silentor
Steady.WhenthefanisinAutomode,itsspeediscontrolledbythetemperatureoftheLED.WhenSilent
modeischosenthefanrunsslowlytoreducethenoise.IfSteadyisactivatedthefanrunsatconstant
speed,halfwaybetweentheminimumandmaximumspeed.Inallcases,ifthetemperatureontheLED
exceedsthemaximumadmittedvalue,theLEDisprotectedbyade‐ratingsecuritysystem,whichlowers
thelightoutputuntilthetemperaturegoesbacktosafelevels,whenfullpoweristhenrestored
automatically.FactorysettingisAUTO.









PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
7 Curves
SQUARE
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
8 CutOff
SLOW
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
9 Smooth
NORMAL
9 Smooth
FAST 
IMMEDIATEDIMMING
RESPONSE
SQUARETOINCREASE
VOLTAGERESPONSEAT
LOWERVALUE
7 Curves
SQUARE 
7 Curves
LINEAR 
LINEARDIMMING
CONTROL
SOFTLEDDIMMINGAT
SHUTDOWN
8 CutOff
SLOW 
8 CutOff
FAST 
DIRECTDIMMING
RESPONSEATSHUT
DOWN
FASTDIMMING
RESPONSE=150ms
9 Smooth
NORMAL 
9 Smooth
SLOW 
SLOWDIMMING
RESPONSE=300ms
PRESSTOACTIVATE
THEMENU,AN
ARROWSHOULD
APPEAR
10 Fan
AUTO
10 Fan
STEADY 
CONSTANTFANSPEED
FANSPEEDIS
REGULATEDBYLED
TEMPERATURE
10 Fan
AUTO 
10 Fan
SILENT 
SLOWFANSPEEDTO
REDUCETHENOISE