LDT SA-DEC-4-MM-G User manual

L ittfinski D aten T echnik ( LDT )
Operating Instruction
Multi-Digital
4-fold switch decoder
from the Digital-Professional-Series !
SA-DEC-4-MM-G Part-No.: 210313
(With possible external power supply)
>> finished module in a case <<
Compatible to Märklin-Motorola-Format:
(e.g. Märklin-Digital∼[Control Unit, Central Station 1
und 2], Intellibox, EasyControl, ECoS, KeyCom-MM,
DiCoStation, EDiTS, EDiTS pro and others)
For digital control of:
⇒consumers up to 2 Ampere on each output
(e.g. illumination, disconnection of track sections from
power).
⇒jammed turnout- and signal drives
(drives with integrated end switch).
This product is not a toy! Not suitable for children under 14 years of age!
The kit contains small parts, which should be kept away from children under 3!
Improper use will imply danger of injuring due to sharp edges and tips! Please store
this instruction carefully.
Introduction/Safety instruction:
You have purchased the 4-fold switch decoder SA-DEC-4 for
your model railway as a finished module in a case.
The SA-DEC-4 is a high quality product that is supplied within
the Digital-Professional-Series of Littfinski DatenTechnik
(LDT).
We wish you having a good time using this product.
The switch decoder SA-DEC-4 of the Digital-Professional-
Series can be easily installed and used on your digital railway.
The decoder SA-DEC-4 is suitable for Märklin-Digital~
respectively for Märklin-Motorola digital format.
The decoder SA-DEC-4 is multi digital and can be installed to
the Intellibox without any problems.
The finished module comes with 24 month warranty.
•Please read the following instructions carefully. Warranty will
expire due to damages caused by disregarding the operating
instructions. LDT will also be not liable for any consequential
damages caused by improper use or installation.
Connecting the decoder to your digital model
railway layout:
•Attention: Before starting the installation switch off the
drive voltage by pushing the stop button from the
command station or disconnect the main supply.
The decoder receives the digital information via the clamp KL2.
Connect the clamp with a rail or even better connect the clamp
directly to the command station or to a booster assuring supply
of digital information free from any interference.
Pay attention to the mark at clamp KL2. The color markings
'Black/Schwarz' and 'Red/Rot' next to the clamp are used for
Arnold-Digital (old) and Märklin-Digital=.
Other systems are using the letters 'J' and 'K'.
If you use the decoder for a Märklin-Digital~ respectively
Märklin-Motorola installation please attend to the colors marks
'red/rot' and 'brown/braun'.
The decoder receives the voltage-supply via the two-pole clamp
KL1. The voltage shall be in the range of 12 to 18V~ (alternating
voltage output of a model railway transformer) or 15 to 24Volt =
(direct voltage output of an insulated power supply unit).
Now connect the consumers (e.g. illumination, motors or turnout-
and signal coils) to the output 1 to 4. The contact marked 'COM'
is the common connection of the bistable relay.
Programming the decoder address:
For programming the decoder address you have to connect a
consumer to the output 1. As it is possible to hear the switching
of the bistable relay the connection of a consumer is not
mandatory.
•Switch on the power supply of your model rail way.
•Depress the programming key S1.
•The relay on output 1 will switch now automatically every 1.5
seconds. This indicates that the decoder is in the
programming mode.
•Depress now one push button assigned to the decoder. For
programming the decoder address you can also release a
turnout switch signal via a personal computer.
S1
1
COM
2
COM
3 4
red brown
K J
COM COM
Littfinski DatenTechnik (LDT)
4-fach Schaltdecoder
4-fold Switch Decoder
SA-DEC-4
Rev. 2.4
KL1
12 ...18V~
15 ... 24V=
Mit 4 bistabilen Relais für Märklin-Motorola
Digitalsysteme. Schaltstrom: 2 Ampere pro
A sgang.
Schaltdecoder
SA-DEC-4-MM
Digital-Profi werden!
Littfinski DatenTechnik (LDT)
www.ldt-infocenter.com
Multi-Digital

Remarks: The decoder addresses for magnet accessories
are combined in groups of four. The address 1 to 4 build the
first group. The address 5 to 8 build the second group etc.
Each SA-DEC-4 decoder can be assigned to any of these
groups. Which of the 4 turnouts of a group will be activated
for the addressing does not matter.
•If the decoder has recognized the assignment correctly the
relay will move a little faster. Afterwards the movement slows
down to the initial 1.5 seconds interval again.
In case the decoder will not recognize the address it could be
that the two digital information connections (clamp 2) are
wrong connected. For testing this, switch off the power
supply, exchange the connection on KL2 and start
addressing again.
•Leave the programming mode by depress the programming
key S1 again. The decoder address is now permanently
stored but can be changed at any time by repeating the
programming as described above.
•If you depress the first key of the programmed group of keys
or you send a switch signal for this turnout from a PC the
addressed bistable relay should now switch the connected
consumer on or off.
Please attend to the following:
•All 4 outputs can switch consumers with up to 2 Ampere.
Decoder application:
Besides the switching of illumination and motors there is an
excellent application for the decoder SA-DEC-4 of digital
switching the Märklin gauge 1 drives (e.g. 5625).
As an advantage large current consuming drives will not
unnecessary overload the expensive digital power supply.
The following draft shows the wiring.
Feed the SA-DEC-4 via KL1 witch AC from the model railway
transformer. Further connect one cable of the transformer with
clamp 'L' on the turnout drive. Connect the second cable of the
transformer with the clamp marked with 'COM' on the respective
decoder output.
Now, connect the two remaining clamps of the decoder output
with the outputs 1and 2of the turnout drive.
Further examples can be found on the web-Site
(www.ldt-infocenter.com) in the download section.
Trouble shooting:
What to do if something is not working as described above?
Here some possible functional errors and possible solutions:
1. During programming of the decoder addresses the relay on
output moves within 1.5 seconds, but does not confirm the
programming with faster movement by depressing any key.
•Change cable connections at KL2.
•Interfered digital information at KL2 respectively lost of
voltage at the tracks! Connect the decoder directly with
cables to the digital control unit or to the booster instead to
the tracks.
•Eventually the clamps have been tightened to strong and
therefore the clamps got loose at the soldering to the pc
board. Check the soldering connection of the clamps at
the lower side of the pc-board and re-solder them if required.
2. The programming of the decoder address functions as
described, nevertheless the connected consumers will not be
activated.
•Interfered digital information on KL2 respectively larger
lost of voltage at the tracks result to unsafe data transfer!
Connect the decoder directly with wires to the command
station or the booster.
Further products within the Digital-Professional-
Series:
S-DEC-4
4-fold turnout decoder for 4 magnet accessories with free
programmable decoder addresses and possible external power
supply.
M-DEC
4-fold decoder for motor driven turnouts. For motors up to 1A.
With free programmable decoder addresses. Drives can be
connected directly with the decoder output.
LS-DEC
Light signal decoder for up to 4 LED train signals. Signal signs
will be originally dimmed up and down and directly positioned via
the decoder address.
RM-88-N / RM-88-N-O
16-fold feedback modules (also with integrated opto-couplings)
for the s88-feedback bus and the connection to Memory and
Interface (Märklin / Arnold), Central Station 1 and 2, ECoS,
Intellibox respectively TWIN-CENTER, EasyControl,
DiCoStation and HSI-88.
RM-GB-8-N
8-fold feedback module with integrated track occupancy
detectors for the s88-feedback bus.
All products are supplied as easy to assemble complete kits or
as finished modules.
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: [phone] / 867-0
Internet: www.ldt-infocenter.com
Subject to technical changes and errors. 02/2022 by LDT
Arnold, Digitrax, Lenz, Märklin, Motorola, Roco and Zimo are
registered trade marks.
S1
1
COM
2
COM
3 4
red brown K J
COM COM
Littfinski DatenTechnik(LDT)
4-fach Schaltdecoder 4-fold Switch Decoder
SA-DEC-4
Rev. 2.4
KL1
12 ...18V~ 15 ... 24V=
Mit 4 bistabilen Relais für Märklin-Motorola Digitalsysteme. Schaltstrom: 2 Ampere pro A sgang. Schaltdecoder SA-DEC-4-MM
Digital-Profi werden!
Littfinski DatenTechnik (LDT)
www.ldt-infocenter.com
Multi-Digital
2
L
1
12 bis 18V~
Antrieb 5625
rot
braun
Modellbahntrafo
Spur 1 Weiche