Lean Cars UTV Datasheet

B
ATTERY P
O
WERED RIDE-
O
N
BATTERY POWERED RIDE-ON
Owner’s Manual
with Assembly Instructions
Styles and colo(u)rs may vary.
Made in China.
The owner’s manual contains important safety information as well as assembly, use and
maintenance instructions.
The Ride-on Car must be assembled by an adult who has read and understands the
instructions in this manual.
Keep the package away from children and dispose of properly before use.
Keep this manual for future reference.
UTV
Type without roof
Type with roof

Battery
Charger
12V10AH*1
12V1000mA
24V7AH *1
24V1000mA
Suitable age:
Load Capacity:
Speed:
Size of car:
Power way:
Charge time:
37-96 months
Under 50kg
3-6km/h
with roof 136 * 87 * 110 cm
without roof 136 * 87 * 85 cm
Charging type
8-12 hours
About Your New Ride-On │ 1
VER: SMS-JS360-EN-202000722
SPECIFICATIONS:
On the purchase of your new Ride-On.
This ride-on will provide your child with many miles of riding of enjoyment. To
help assure you and your rider a safe ride we ask you to please read this manual
carefully, and keep it for future reference.
Follow the recommendations in this manual, they are designed to improve the
safety and operation of your ride-on car and it’s rider.

The following safety hazards may result in serious injury or death:
• Never leave child unattended. Direct adult supervision is required. Always keep child in view
when child is in vehicle.
• To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor
vehicles, on or near steep inclines or steps, swimming pools or other bodies of water, always
wear shoes, and never allow more than 2 rider.
• Never use in unsafe conditions such as snow, rain, loose dirt, mud, sand, or gravel,
otherwise may result in an unexpected accident such as tipping over, and could damage the
electrical system or battery
• Not to be used in traffic.
• This toy should be used with caution since skill is required to avoid falls or collisions causing
injury to the user or third parties.
• This toy is unsuitable for children under 36 months due to its maximum speed; Maximum
user weight is 50kg.
• This toy has no brake.
User Notice │ 2
WARNING!
SAFETY
●Non-rechargeable batteries are not to be recharged.
●Rechargeable batteries are to be removed from the toy before being charged.
●Rechargeable batteries are only to be charged under adult supervision.
●Different types of batteries or new and used batteries are not to be mixed.
●Batteries are to be inserted with the correct polarity.
●Exhausted batteries are to be removed from the toy.
●The supply terminals are not to be short-circuited.
BATTERY INFORMATION
• CHOKING HAZARD - Small parts. Not suitable for children under 36 months. The product
contains small parts, keep children away when assembling.
• ADULT ASSEMBLY REQUIRED.
• Always remove protective material and poly bags and dispose before
assembly.
• Protective equipment should be worn. Always wear shoes and sit in the seat when operating
the vehicle.
• Only drive on level ground. Never use on the lawn.
• Never leave a child unattended.
• Keep your hands, hair, and clothes away from moving parts.

25 29
26
1
28
4
3
5
5
27
6
627
2
7
8
910
11
19
20
20
21
23
21
24
22 22 13
15
15
15
15
16
17
18
12
14
15
15
15
15
15
4
4
HINT: Some parts shown are assembled on both sides of vehicle
Parts Diagram │ 3
Type without roof
Type with roof

PART
NO.
REMARKS
PART NAME
Q’ty (pcs)
Vehicle body
Rear wheel
Front wheel
Ø12 washer
Lock nut
Hubcap
rear axle
Steering wheel
M5x35 machine screw
Ø5 nut
Seat cushion
Seat back
Cargo basket
M5x16 mahine screw
Ø4x16 screw
Front rollbar
Rear Rollbar linkage
Rear Rollbar support
Roof
Roof beam
Roof front support
Roof rear support
M5x30 machine screw
Ø5 nut
Charger
Spanner
Split pin
Front bumper
Remote controller
Placed on the steering wheel
For R/C type only
Placed on the steering wheel
Left and right
Left and right
Left and right
Left and right
Parts List │ 4
without roof with roof
2WD 1 PC labeled “R”, the other one labeled “L”
Assembly tools required (not included):
Screwdriver
Long nose pliers
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
2
2
6
4
4
1
1
1
1
1
1
1
2
12
1
1
2
/
/
/
/
/
/
1
2
4
1
1
1
2
2
6
4
4
1
1
1
1
1
1
1
2
14
/
/
/
1
2
2
2
8
8
1
2
4
1
1

2
1
Attach the Front Bumper & Rear Axle │ 5
1. Insert the tabs on the front bumper into the holes in the front of the vehicle, push until
you hear it “click” into place.
• Turn the vehicle body downside up. Cut off the plastic tie on the front axle with
scissors. Remove all the parts from the rear axle.
2. Insert the rear axle through the hole in the gear box and the hole in the back of the
vehicle, when inserting it half way, lift the another gear box so that the rear axle can
go through it and protrude out. Make sure that the rear axle is centered with left and
right ends exposed the same distance outside of the vehicle body.
Rear Bottom View

1
2
34
5
Attach the Rear Wheels │ 6
1. Slide the rear wheel onto the rear axle, ensure the driver on the wheel match up with
the gear box.
2. Slide a Ø12 washer onto the rear axle.
3. Tighten a lock nut to the end of the front axle with a spanner.
• Repeat the above procedure to assemble the other rear wheel. HINT: An extra
spanner has been provided to hold the Lock Nut on the other side of the rear axle
while tightening the Lock Nut on the other side. DO NOT over tighten.
4. Insert the split pin into the hole on each end of the rear axle. Bend the ends of split
pins back using a long nose pliers (not included).
5. “Snap” the hubcaps to the wheels.
Rear Bottom View

7-1 7-2
Reset the Front Axle │ 7
M6x16 machine screw
Ø6 lock nut
Ø6
washer
Front axle plate
Front axle plate
Steering linkage
Steering linkage
Steering column
Cut off the plastic tie on the front axle with scissors.
7-1. Adjust the front axle plate so that the axle is in the correct position as shown.
7-2. Then insert the M6x16 screw through the hole in the steering linkage, the Ø6
washer and the hole in the front axle plate (ensure the steering linkage sits over the
front axle plate as shown), attach the locknut and tighten securely. DO NOT over
tighten.
Front Bottom View

43
2
1
65
Attach the Front Wheels │ 8
Front Bottom View
Remove all the parts from the front axle.
1. Slide a Ø12 washer onto the front axle.
2. Slide a front wheel onto the front alxe.
3. Slide a Ø12 washer onto the front axle.
4. Tighten a lock nut to the end of the front axle with a spanner. DO NOT over tgithen.
5. Insert a split pin into the hole on the end of the rear axle. Bend the ends of split pin
back using a long nose pliers (not included).
5. “Snap” the hubcap to the wheel.
Repeat the above procedure to assemble the other normal wheel.
GAP
After assembling any wheel to the axles, please check the gap
between the screw thread and the collapsible (refer to below
picture), if the gap is too big, please add two or three washers
inside the wheel, but after tightening the nut outside the wheel,
please turn the wheel by your finger to check if the wheel can
run smoothly, this is very important, because if the wheel can
run smoothly, it is ok, but if the nut press the wheel and the
wheel can’t run smoothly, the motor will be broken easily! Then
you need to decrease one or two washers to make sure the
wheel can run smoothly!

2
4
31
6
7
5
Attach the Steering Wheel │ 9
Remove the M5x35 machine screw and Ø5 nut from the steering wheel.
Turn the vehicle body upright.
5. Place the steering wheel over the the steering column, protruding from the middle of
1. With a screwdriver remove the
screw on the battery cover located
in the center of the steering wheel.
2. Remove the battery cover from the
top of the battery compartment.
3. Insert 2x1.5 AA batteries in their
correct polarities.
4. Place the battery cover over the
battery compartment and fasten
with the screw you removed in step
one.
Attach the Steering Wheel
HINT: If the steering wheel of your vehicle equipped with the sound function, please
follow the steps 1-4 to add the batteries (Not Included), and refer to the battery
information on page 2.
the steering wheel base.
6. Align the holes on each side of steering
End of steering column
wheel with the holes at the end
of the steering column.
7. Fasten a nut on the opposite
end of the screw to secure the
steering wheel to the steering
column.

3
1
2
Attach the Cargo Basket & Connect the Power Supply │ 10
1. Fit the cargo basket to the bonnet.
2. Insert four Ø4x16 screws and tighten.
3. Plug the battery connector into the vehicle connector.
Battery connector
Vehicle connector
Top View

1
2
3
4
Attach the Seat │ 11
1. Fit the seat back to the seat.
2. Fit the seat assembly to the vehicle body.
3. Insert two M5x16 machine screws through the seat
and into the vehicle, and tighten with a screwdriver.
4. Insert two Ø4x16 screws through the seat back and
into the vehicle body and tighten.
Seat Bottom View

11
3
22
4
4
Attach the Rear Rollbar │ 12
1. Fit the rear rollbar support to the each end of the rear rollbar linkage.
2. Insert a Ø4x16 screw and tighten on each side.
3. Fit the rear rollbar assembly to the vehicle body.
4. Tighten two Ø4x16 screws on each side with a screwdriver.
HINT: The follow steps only for the type without roof.

1
Attach the Front Rollbar │ 13
1. Insert the front rollbar into the holes in the top side of the vehicle body. Push until
you hear it “click” into place.
Type without roof completed.
battery
HINT: The follow steps only for the type without roof.

1
2
4
6
3
5
L1
L1
L2
L2
Attach the Roof(1) │ 14
1. Fit the both roof beams to the roof.
2. Insert the three Ø4x16 screws and tighten.
3-4. Fit the rear rollbar support to the roof beam, using M5x35 machines *2 and Ø5 locknut *2
to secure it. Repeat for the other side. (L2 to L2, R2 to R2)
5-6. Fit the front rollbar support to the beam, using M5x35 machines *2 and Ø5 locknut *2 to
secure it. Repeat for the other side. (L1 to L1, R1 to R1)
“R” marked
“R” marked
“L” marked
“L” marked
HINT: The roof, roof beams, roof front supports and roof rear supports are marked
“L” and “R”, aslo they are designed to assemble together in only one way.
Please follow the guides: L to L, R to R.
HINT: The follow steps only for the type with roof.

1
23
Attach the Roof(2) │ 15
1. Fit the roof assembly to the vehicle body.
2. Insert a Ø4x16 screw through the both roof front supports and into the bonnet, and
tighten with a screwdriver.
HINT: The follow steps only for the type with roof.
3. Insert two Ø4x16 screws through the rear
rollbar support and into the vehicle body. and
tighten with a screwdriver. repeat for the
other side.
Type with roof completed.

1
2
3
4
Use Your Ride-on │ 16
Use the vehicle on generally level ground ONLY! DO NOT Use the vehicle on Lawn space!
●Always stop vehicle when changing the speed (if equipped) or direction to
avoid damage the gears and motor.
IMPORTANT
1. Power button: Turns the vehicle on and off.
2. Low speed forward/reverse shifter: Changes the direction that vehicle moves from forward
to reverse.
●To move the vehicle forward, shift the lever to top position.
●To move the vehicle backward, shift the lever to down position.
3. Foot pedal: Applies power (speed) to the vehicle.
●To move the car, press the pedal down.
●To brake or slow down, release pressure from the pedal.
4. Sound buttons: Press for sound playing.

B
A
Using the High Speed │ 17
●The High Speed Protective cover must be removed by an adult.
●Before remove the HIGH SPEED protective cover: Make sure your child knows
how to steer, how to start and stop the product and knows the rules for safe
driving.
IMPORTANT
Reverse
Reverse
Low speed
forward
Low speed
forward
High speed forward
High speed forward
A. Remove the two screws on the top of the high speed protective cover with a
screwdriver.
B. Remove the high speed protective cover.
Then you can push the shifter into the “high speed” position.
C. Press down the foot pedal.
HINT: The product is designed to operate in low speed only in reverse.

Battery Disposal
The battery will eventually lose the ability to hold a charge. Depending on the amount of use, and
varying conditions, the battery should operate for one to three years.
Important! Recycle the dead battery responsibly. The battery contains lead acid (electrolyte) and
must be disposed of properly and legally. It is illegal in most areas to incinerate lead acid batteries
or dispose of them in landfills. Take it to a federal or state-approved lead acid battery recycler,
such as local automotive battery retailer.
Do not throw the battery away with your regular household waste!
Charging │ 18
• The POWER SWITCH must be turned in OFF position when charging.
• Before the first use, you should charge the battery for 4-6 hours. Do not recharge the battery
for more than 10 hours to avoid overheating the charger.
• When the vehicle begins to run slowly, recharge the battery.
• After each use or once a month minimum recharge time as 8 to 12 hours, less than 20 hours at
most.
• Use the only rechargeable battery and charger supplied with your vehicle. NEVER substitute the
battery or the charger with another brand. Using another battery or charger may cause a fire or
explosion.
• Do not use the battery or charger for any other product.
• If your ride-on with a Digital voltmeter(IF EQUIPPED), the magnitude of voltage will tell you how
much power is remaining in the battery when you must recharge the battery. Make sure the
vehicle is stop!
12V product
24V product
less than 12.5v
less than 24v The battery needs to be charge.
• ONLY an adult is allowed charge and recharge the battery!
• This product with Charging Protection: when charging, all functions will be
cut off.
WARNING!
2
1. Plug the charger port into the input socket (the socket below the seat).
2. Plug the charger plug into a wall outlet. The battery will begin charging.
1