Ledj LEDJ266 User manual

Order code: LEDJ266
Vector Beam Quad
User Manual

www.prolight.co.uk Vector Beam Quad User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Oneyearfromdateofpurchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk Vector Beam Quad User Manual
3
Product overview & technical specications
TheVectorBeamQuadisadynamicmulti-beambatteneffectfeaturingtwosweepingLEDbars,eachloadedwith
fourindividuallycontrollablenarrowbeams.Dispensingeightintenseandsharplong-throwbeamstheVector
Beamcutsthroughtheairwithease.Thefourbuttonmenusystemallowscontrolofmaster/slavefunctions,and
thexturecanbealsobeoperatedinsoundactiveandDMXmodes.
•8x10WCREEquad-colourLEDs
•Beamangle:3°
•IndividuallycontrollableLEDs
•1.5kHzrefreshrate
•DMXchannels:1/36or
40selectable
•Soundactive,autoandmasterslavemodes
plusbuiltinprograms
•0-100%dimmingandvariablestrobe
•Tilt:180°
•Tiltautocorrection
•4pushbuttonmenu
withLCDdisplay
•PowerCONin/outsockets
•3-PinXLRin/outsockets
•5-PinXLRin/outsockets
•ConvectioncooledLED’s
•Quickreleaseomegaclampsincluded
Vector Beam Quad
Specications Vector Beam Quad
Powerconsumption 110W
Powersupply 100~240V,50/60Hz
Dimensions 156x1066x80mm
Weight 8.7kg
Ordercode LEDJ266
0m 1m 2m 3m 4m 5m
3° - Lux
R
G
B
W
8993
14720
3143
24640
2743
3949
872
7328
1239
1725
370
3326
3°
718
960
210
1887
475
626
135
1231
1066mm 80mm
156mm

www.prolight.co.uk Vector Beam Quad User Manual
4
Technical specications
01-LCDdisplay
02-Menubutton
03-Enterbutton
04-Upbutton
05-Downbutton
06-3-pinDMXinsocket
07-5-pinDMXinsocket
08-PowerCONinsocket
09-FuseF2A250V
10-On/offswitch
11-Earthpoint
12-PowerCONoutsocket
13-5-pinDMXoutsocket
14-3-pinDMXoutsocket
15-Rubberfeet
16-Fanvents
17-Omegaclampmounts
18-Safetybondpoint
02
03
04
05
06
15 1516 1617 17 17 1718
07 08 09 10 11 12 13 14
01
MENU UPENTER DOWN
3-PIN DMX IN 5-PIN DMX IN
POWER IN
100-240V~50/60Hz FUSE: T2.0A 250V ON
OFF
3-PIN DMX OUT5-PIN DMX OUT
POWER OUT
100-240V~50/60Hz
BEAM
ector
V
Q U A D
MENU UPENTER DOWN
3-PIN DMX IN 5-PIN DMX IN
POWER IN
100-240V~50/60Hz FUSE: T2.0A 250V ON
OFF
3-PIN DMX OUT5-PIN DMX OUT
POWER OUT
100-240V~50/60Hz
BEAM
ector
V
Q U A D
MENU UPENTER DOWN
3-PIN DMX IN 5-PIN DMX IN
POWER IN
100-240V~50/60Hz FUSE: T2.0A 250V ON
OFF
3-PIN DMX OUT5-PIN DMX OUT
POWER OUT
100-240V~50/60Hz
BEAM
ector
V
Q U A D
MENU UPENTER DOWN
3-PIN DMX IN 5-PIN DMX IN
POWER IN
100-240V~50/60Hz FUSE: T2.0A 250V ON
OFF
3-PIN DMX OUT5-PIN DMX OUT
POWER OUT
100-240V~50/60Hz
BEAM
ector
V
Q U A D
Inthebox:1 x xture,
1 x power cable,
1 x user manual &
2 x small omega clamps

www.prolight.co.uk Vector Beam Quad User Manual
5
Operating instructions
DMX channel mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomesto
customisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthexture
andeachxtureindependently.
ToaccesstheDMXchannelmode,pressthe“MENU”buttonontherearoftheunittoshow“DMX” 
ontheLCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP” and“DOWN” buttonstoadjust
eachsetting.
The“Address”settingallowstheusertoadjusttheDMXaddressbetweeen“001”and“512”.
The“Channel”settingallowstheusertoselectfromonetheDMXchannels“1/36 or 40”and“512”.
Please note:WhenaDMXleadisconnectedandasignalisbeingreceivedcorrectlytheLCDdisplaywill
show“DMX IN”.
Channel Value Function
10-19 Blackout
20-29 Show1
30-39 Show2
40-49 Show3
50-59 Show4
60-69 Show5
70-79 Show6
80-89 Show7
90-99 Show8
100-109 Show9
110-119 Show10
120-139 Blackout
140-255 Soundactive
(adjustablesensitivity-
140:low,255:high)
1 channel mode:

www.prolight.co.uk Vector Beam Quad User Manual
6
Operating instructions
Channel Value Function
1000-180 Leftbar0-180°tilt
181-255 Leftbarisstaticat180°
2000-255 Leftbartiltspeed(000:fast,255:slow)
3000-255 Rightbartilt0-180°
000-255 Rightbarisstaticat180°
4000-255 Rightbartiltspeed(000:fast,255:slow)
5 000-255 LED1Red(0-100%dimming)
6 000-255 LED1Green(0-100%dimming)
7 000-255 LED1Blue(0-100%dimming)
8000-255 LED1White(0-100%dimming)
9000-255 LED2Red(0-100%dimming)
10 000-255 LED2Green(0-100%dimming)
11 000-255 LED2Blue(0-100%dimming)
12 000-255 LED2White(0-100%dimming)
13 000-255 LED3Red(0-100%dimming)
14 000-255 LED3Green(0-100%dimming)
15 000-255 LED3Blue(0-100%dimming)
16 000-255 LED3White(0-100%dimming)
17 000-255 LED4Red(0-100%dimming)
18 000-255 LED4Green(0-100%dimming)
19 000-255 LED4Blue(0-100%dimming)
20 000-255 LED4White(0-100%dimming)
21 000-255 LED5Red(0-100%dimming)
22 000-255 LED5Green(0-100%dimming)
23 000-255 LED5Blue(0-100%dimming)
24 000-255 LED5White(0-100%dimming)
25 000-255 LED6Red(0-100%dimming)
26 000-255 LED6Green(0-100%dimming)
27 000-255 LED6Blue(0-100%dimming)
28 000-255 LED6White(0-100%dimming)
29 000-255 LED7Red(0-100%dimming)
30 000-255 LED7Green(0-100%dimming)
31 000-255 LED7Blue(0-100%dimming)
32 000-255 LED7White(0-100%dimming)
33 000-255 LED8Red(0-100%dimming)
34 000-255 LED8Green(0-100%dimming)
35 000-255 LED8Blue(0-100%dimming)
36 000-255 LED8White(0-100%dimming)
36 channel mode:

www.prolight.co.uk Vector Beam Quad User Manual
7
Operating instructions
Channel Value Function
1000-180 Leftbar0-180°tilt
181-255 Leftbarisstaticat180°
2000-255 Leftbartiltspeed
(000:fast,255:slow)
3000-255 Rightbar0-180°tilt
000-255 Rightbarisstaticat180°
4000-255 Rightbartiltspeed
(000:fast,255:slow)
5 000-255 Masterdimmer
6 000-009 Blackout
000-019 LEDmacro-Usechannels1-4
toadjustbarpositions
020-029 Show1
030-039 Show2
040-049 Show3
050-059 Show4
060-069 Show5
070-079 Show6
080-089 Show7
090-099 Show8
100-109 Show9
110-119 Show10
120-139 Blackout
140-255 Soundactive(adjustable
sensitivity-140:low,255:high)
7 000-255 Speed(onlyforLEDmacro)
8000-014 LEDnostrobe
015-255 LEDstrobe(015:slow,255:fast)
9000-255 LED1Red(0-100%dimming)
10 000-255 LED1Green(0-100%dimming)
40 channel mode:
11 000-255 LED1Blue(0-100%dimming)
12 000-255 LED1White(0-100%dimming)
13 000-255 LED2Red(0-100%dimming)
14 000-255 LED2Green(0-100%dimming)
15 000-255 LED2Blue(0-100%dimming)
16 000-255 LED2White(0-100%dimming)
17 000-255 LED3Red(0-100%dimming)
18 000-255 LED3Green(0-100%dimming)
19 000-255 LED3Blue(0-100%dimming)
20 000-255 LED3White(0-100%dimming)
21 000-255 LED4Red(0-100%dimming)
22 000-255 LED4Green(0-100%dimming)
23 000-255 LED4Blue(0-100%dimming)
24 000-255 LED4White(0-100%dimming)
25 000-255 LED5Red(0-100%dimming)
26 000-255 LED5Green(0-100%dimming)
27 000-255 LED5Blue(0-100%dimming)
28 000-255 LED5White(0-100%dimming)
29 000-255 LED6Red(0-100%dimming)
30 000-255 LED6Green(0-100%dimming)
31 000-255 LED6Blue(0-100%dimming)
32 000-255 LED6White(0-100%dimming)
33 000-255 LED7Red(0-100%dimming)
34 000-255 LED7Green(0-100%dimming)
35 000-255 LED7Blue(0-100%dimming)
36 000-255 LED7White(0-100%dimming)
37 000-255 LED8Red(0-100%dimming)
38 000-255 LED8Green(0-100%dimming)
39 000-255 LED8Blue(0-100%dimming)
40 000-255 LED8White(0-100%dimming)
Show mode:
Toaccessshowmode,pressthe“MENU”buttonontherearoftheunittoshow“SHOW” onthe
LCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP” and“DOWN” buttonstoselectbetween
“SHOW 1 to SHOW 10”.
Auto mode:
Toaccessautomode,pressthe“MENU”buttonontherearoftheunittoshow“AUTO”ontheLCD
display. Thexturewillnowcyclethroughthebuiltinprograms.Ifthe“SETUP”buttonisthenpressed
thedisplaywillnowbringupalistofsettingswithinautomode.Theseareasfollows:

www.prolight.co.uk Vector Beam Quad User Manual
8
Operating instructions
LED:
Press“ENTER”togointotheLEDsettings.Withinthistheusercaneitherchoose“e-Auto”or“e-Manul”.
“e-Auto”-pressthe“ENTER”buttonforamenutoadjustthespeedandfrequency.
“SPEED”-pressthe“ENTER”buttontoadjustthespeedbetween“1-20”(1beingslowest,
20beingfastest).
“FREQ”-pressthe“ENTER”buttontoadjusttheashspeedfrom“00-20Hz”(00beinglowest,
20beinghighest).
“e-Manul”-pressthe“ENTER”buttonforamenutochoosethecolouryourequire:
Red/Green/Blue/White/Yellow/Cyan/Purple/LightRed/LightGreen/LightBlue/Allon/Black.
BAR:
Press“ENTER”togointotheBARsettings.Withinthistheusercaneitherchoose“m-Auto”
or“m-Manul”.
“m-Auto”-pressthe“ENTER”buttontoadjustthespeedbetween“16”(1beingslowest,
16beingfastest).
“m-Manul”-pressthe“ENTER”buttontoadjustthepositionoftheleftandrightbar.
“L-BAR”-pressthe“ENTER”buttontoadjusttheleftbarbetween“0-180°”.
“R-BAR”-pressthe“ENTER”buttontoadjusttheleftbarbetween“0-180°”.
Sound mode:
Toaccesssoundmode,pressthe“MENU”buttonontherearoftheunittoshow“SOUND” onthe
LCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP” and“DOWN” buttonstoselectthe
sensitivitybetween“01-31”(01beinglowest,31beinghighest).
Slave mode:
Toaccesssoundmode,pressthe“MENU”buttonontherearoftheunittoshow“SLAVE” onthe
LCDdisplay.
Settings:
Toaccessthexturessettings,pressthe“MENU”buttonontherearoftheunittoshow“SETTINGS” on
theLCDdisplay. Nowpressthe“ENTER”buttonandusethe“UP” and“DOWN” buttonstoadjust
eachsetting.Theseareasfollows:
“BL TIME”-pressthe“ENTER”buttontoadjusttheLCDbacklightautoswitch-offtimefrom“ON”
to“30s”.
“ADJUST”-pressthe“ENTER”buttontomanuallyadjusttheelectronicmotorpositionoftheleftand
rightbarfrom“-999 - +999”.
“RESET”-pressthe“ENTER”buttontorestorethefactorysettings.Youcanalsodothisbyholding
“MENU”and“ENTER”whentheunitisbeingpoweredup.
“MOTO”-pressthe“ENTER”buttonandtheunitwilldisplayaresetcode.
“POWER”-pressthe“ENTER”buttonandtheunitwilldisplaythexturesvoltage.
“ABOUT”-pressthe“ENTER”buttonandtheunitwilldisplaythemodel.

www.prolight.co.uk Vector Beam Quad User Manual
9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m (3-pin)
CABL11 – 5m (3-pin)
CABL12 – 10m (3-pin)
CABL185 - 2m (5-pin)
CABL187 - 5m (5-pin)
CABL188 - 10m (5-pin)

www.prolight.co.uk Vector Beam Quad User Manual
10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Vector Beam Quad User Manual
11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk Vector Beam Quad User Manual 12