Ledj Mini Pix 9 Panel User manual

Order code: LEDJ261
Mini Pix 9 Panel
(9 x 9W tri-colour COB LEDs)
User Manual

www.prolight.co.uk Mini Pix 9 Panel User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Oneyearfromdateofpurchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk Mini Pix 9 Panel User Manual 3
Product overview & technical specications
TheMiniPix9paneloffersfullpixelmappingtechnology
withinacompact,ruggedchassisallowinglightingdesigners
andDJstocreatestunningonstageeyecandytypeeffects.
9WCOB(chip-on-board)tri-colourLEDsdeliverafull
spectrumofcolours,chasesandpatternsaccessiblefrom
alargenumberofinternalprograms.TheMiniPix9panel
alsohasanumberofbuilt-inDMXpersonalitiestosimplify
integrationandcompatibilitywithvarietyofDMXconsoles.
•9x9Wtri-colourCOBLEDs
•Beamangle:25°
•DMXchannels:3/4/5/27or30selectable
•Staticcolour,colourmix,colourchange,colourfade,built-in
programs,auto,soundactiveandmaster/slavemodes
•Remotedevicemanagement(RDM)
•Bracketallowsformultipleriggingapplications
•4pushbuttonmenuwithLEDdisplay
•3-PinXLRin/outsockets
•IECpowerin/outsockets
•Fancooled
Mini Pix 9 Panel
Specications Mini Pix 9 Panel
Powerconsumption 116W
Powersupply 100~240V,50/60Hz
Fuse 1A250V(2A125V)
Dimensions 300x259x169mm
Weight 4.8kg
Ordercode LEDJ261
0m 1m 2m 3m 4m 5m
25° - Lux 3370 1011 475
25°
265 171
259mm 169mm
300mm

www.prolight.co.uk Mini Pix 9 Panel User Manual 4
Technical specications
01-Bracket
02-Brackettighteningknobs
03-Earthpoint
04-Safetyeye
05-LEDdisplay
06-Functionbuttons
07-DMXinputsocket
08-DMXoutputsocket
09-IECpowerinsocket
10-IECpoweroutsocket
11-Fuse1A250V(2A125V)
12-Mic
Inthebox:1 x xture,
1 x power cable &
1 x user manual
PUSH
MODE ENTER UP DOWN
DMX OUT
MIC
DMX IN
POWER IN POWER OUT
www.prolight.co.uk
01
02
07
09
11
08
10
12
03
04
05 06

www.prolight.co.uk Mini Pix 9 Panel User Manual 5
Operating instructions
DMX channel mode:
OperatinginDMXcontrolmodegivestheuserthegreatestexibilitywhenitcomestocustomising
orcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthextureandeach
xtureindependently.
ToaccesstheDMXchannelmode,pressthe“MODE”buttonontherearoftheunittoshow“DMX MODE”
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
desiredDMXaddress.Nowpressthe“ENTER”buttontochooseoneofthe3,4,5,27or30DMX
channelmodesusethe“UP”and“DOWN”buttons,andpressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
3 channel mode: 4 channel mode:
CH1 CH2 CH3 CH4
0-15BLACKOUT
Masterdimmer
(Activewhen
CH1valueis
0-255)
Flash(0-255)
Slowtofast
16-23R
24-31G
32-39B
40-47RG
48-55GB
56-63RB
64-71RGB
72-79Colour1
80-87Colour2
88-95Colour3
96-103Colour4
104-111Colour5
112-119Colour6
120-127Colour7
128-135Colour8
136-143DREAM
Speed(0-255)
Slowtofast
(ActivewhenCH1
valueis136-255)
144-151METEOR
152-159FADE
160-167CHANGE
168-175FLOW1
176-183FLOW2
184-191FLOW3
192-199FLOW4
200-207FLOW5
208-215FLOW6
216-223FLOW7
224-231FLOW8
232-239FLOW9
240-255SOUND

www.prolight.co.uk Mini Pix 9 Panel User Manual 6
Operating instructions
5 channel mode:
27 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 Masterdimmer(0-100%)
5 000-000 ON
001-005 Soundcontrol(7colours)
006-010 ON
011-255 Strobe(increasing)
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
R1
(0-255)
G1
(0-255)
B1
(0-255)
R2
(0-255)
G2
(0-255)
B2
(0-255)
R3
(0-255)
G3
(0-255)
B3
(0-255)
CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27
R7
(0-255)
G7
(0-255)
B7
(0-255)
R8
(0-255)
G8
(0-255)
B8
(0-255)
R9
(0-255)
G9
(0-255)
B9
(0-255)
CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18
R4
(0-255)
G4
(0-255)
B4
(0-255)
R5
(0-255)
G5
(0-255)
B5
(0-255)
R6
(0-255)
G6
(0-255)
B6
(0-255)

www.prolight.co.uk Mini Pix 9 Panel User Manual 7
30 channel mode:
Operating instructions
CH1 CH2 CH3 CH4 CH5 CH6 ...CH15
0-15BLACKOUT
Masterdimmer
(ActivewhenCH1
valueis0-135)
Flash(0-255)
Slowtofast R(0-255) G(0-255) B(0-255) ...
16-23R
24-31G
32-39B
40-47RG
48-55GB
56-63RB
64-71RGB
72-79Colour1
80-87Colour2
88-95Colour3
96-103Colour4
104-111Colour5
112-119Colour6
120-127Colour7
128-135Colour8
136-143DREAM
Speed(0-255)
Slowtofast
(ActivewhenCH1
valueis136-239)
144-151METEOR
152-159FADE
160-167CHANGE
168-175FLOW1
176-183FLOW2
184-191FLOW3
192-199FLOW4
200-207FLOW5
208-215FLOW6
216-223FLOW7
224-231FLOW8
232-239FLOW9
240-255SOUND
Sensitivity(0-255)
(ActivewhenCH1sound
valueis240-255)

www.prolight.co.uk Mini Pix 9 Panel User Manual 8
Master/slave mode
Tosetthemasterunit,pressthe“MODE”buttonontherearofthemasterunitthenselectyour
desiredprogram(soundactive,auto,staticcolouroroneofthebuilt-inprograms).Tosettheother
unitsinslavemode,pressthe“MODE”buttonontherearoftheunittoshow“SLAVE MODE”onthe
LEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitwillnowruninsequence
withthemasterunit.Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Sound active mode:
Toaccessthesoundactivemode,pressthe“MODE”buttonontherearoftheunittoshow
“SOUND MODE”ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstosetthesoundsensitivitylevelandpressthe“ENTER”buttontoconrmthesetting.
“SENS” 00 - 31 (00 = low, 31 = high)
Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthefrequencylevel
andpressthe“ENTER”buttontoconrmthesetting.
“FQN” 01 - 99 (01 = low, 99 = high)
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Auto run mode:
Toaccesstheautorunmode,pressthe“MODE”buttontoshow“AUTO RUN”ontherearoftheunit.
Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthefrequencyleveland
pressthe“ENTER”buttontoconrmthesetting.
“FQN” 01 - 99 (01 = low, 99 = high) -Thefrequencyleveladjustshowmanytimestheprogram
repeatsbeforemovingtothenextprogram.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Note: In this mode, it will run 14 built-in programs in a continuous loop.
Built-in programs mode
Toaccessthebuilt-inprogramsmode,pressthe“MODE”buttonontherearoftheunittoshow
“01.STATIC”ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttons
toselectbetweenthe14built-inprograms.Nowpressthe“ENTER”buttontoselectthedesiredspeed
andadjustbyusingtheand“DOWN”buttons.
Speed values: 01 - 99 (00 = slow, 99 = fast)
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
See next page for built-in programs chart.
Operating instructions

www.prolight.co.uk Mini Pix 9 Panel User Manual 9
Invert mode:
Toaccesstheinvertmode,pressthe“MODE”buttonontherearoftheunittoshow“INVERT ON/OFF”
ontheLCDscreen.Pressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoturnthethis
modeonandoff.
OFF = Left to Right ow
ON = Right to Left ow
Inthismodeviathe“ON/OFF”options,youcanadjustthe
effectdirectionfrom‘lefttoright’orfrom‘righttoleft’.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Dimming curve:
Toaccessthedimmingcurvemode,pressthe“MODE”buttonontherearoftheunittoshow
“DIMMER CURVE”ontheLCDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstoselectbetweenthe2dimmingcurves.
01 = Halogen emulation mode with a very smooth slow dimming and a small delay.
02 = LED response with faster dimming and no delay.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Operating instructions
01 STATICColour-CL:RGBFlash00-99 Blackout,Red-Green-Blue-Yellow-Cyan-Purple-White
Flashspeedadjustable
02 DREAM-Speed00-99Flash00-99 Sevencolourdreaming-Speed&Flashadjustable
03 METEOR-Speed00-99Flash00-99 Sevencolourow-Speed&Flashadjustable
04 FADE-Speed00-99Flash00-99 Sevencolourfade-Speed&Flashadjustable
05 CHANGE-Speed00-99Flash00-99 Sevencolourchange-Speed&Flashadjustable
06 FLOW1-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
07 FLOW2-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
08 FLOW3-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
09 FLOW4-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
10 FLOW5-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
11 FLOW6-Speed00-99Flash00-99 Sevencolourchase(digitalnumber0-9)-Speed&Flashadjustable
12 FLOW7-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
13 FLOW8-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
14 FLOW9-Speed00-99Flash00-99 Sevencolourchase-Speed&Flashadjustable
1
4
7
2
5
8
3
6
9
3
6
9
2
5
8
1
4
7
INVERTED

www.prolight.co.uk Mini Pix 9 Panel User Manual 10
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Mini Pix 9 Panel User Manual 11
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterferance.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Mini Pix 9 Panel User Manual 12
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.