LEGRAND 0 488 64 User manual

87045 LIMOGES Cedex France
Telephone: [phone] - Fax: [phone]
Technical data sheet: S000064192EN-3
Catalogue number(s): 0 488 64
Updated: 29/10/2015 Created: 03/05/2012
Controller - 4 x DALI circuits -
BUS/KNX
CONTENTS 1/6
CONTENTS Page
1. Use ............................1
2. Technical characteristics ...........1
3. Dimensions......................2
4. Connection ......................2
5. Installation ......................3
6. Parameter setting.................4
7. Communication objects ............4
8. Care ...........................6
9. Standards .......................6
230 V~
32 ballasts max./channel
110 V~
1. USE
This device is a power unit for managing lighting loads (DALI or DSI).
It must be connected to one or more sensors and/or remote auxiliary
controls in order to operate.
The load(s) can be controlled manually or automatically by the sensors
and/or the controls associated with the device.
2. TECHNICAL CHARACTERISTICS
Red LED:
indicates that the BUS
capacity has been exceeded
DALI LED:
indicates the
learning phase or
RESET of the
DALI or DSI ballasts
LEARN LED:
indicates the learning
phase or RESET
Indicators
(on if output
activated)
Control
buttons
1
1DALI ballast
2. TECHNICAL CHARACTERISTICS (continued)
Voltage: 100-240 V~
Frequency: 50/60 Hz
No load power consumption: 2.4 W
Control side
•BUS
Connection between the compatible peripherals in the offer and
the controller: RJ 45 cord or BUS cable to fit RJ 45 connector (
max. 150 m between the controller and the furthest peripherals)
•KNX
Connection between the controller and products in the KNX offer:
KNX cable fitted with red, black KNX connector (350 m max. of
cable between the power supply and the furthest product. Beyond
this distance, repeaters must be used.)
Power side
Power supply: 2 x 2.5 mm2(screw terminals)
DALI 1.5 mm2
KNX
BUS
"PROG & RESET LED"
"PROG & RESET button"
The product incorporates positive safety
- If there is a peripheral fault on the BUS ,
the lights come back on automatically after 10 minutes.
Product installation: in a suspended ceiling or on a suitable cable tray
DALI

Catalogue number(s): 0 488 64
Controller - 4 x DALI circuits -
BUS/KNX
Technical data sheet: S000064192EN-3 Updated: 29/10/2015 Created: 03/05/2012
2/6
CONTENTS
Schematic diagram
BUS/KNX connection
350 m max.
Controllers
BUS/KNX power supply
Cat. No. 0 035 12
IP communication
module
Cat. No. 0 035 43
2. TECHNICAL CHARACTERISTICS (continued)
Peripherals compatible with the KNX offer:
- BUS sensors: infrared, ultrasound or dual technology
- Pushbutton lighting controls, switch and scenario management
multifunction controls.
Usage temperature: -5°C to +45°C
Storage temperature: -20°C to +70°C
Weight: 525 g
Impact resistance: IK04
Penetration by solid and liquid matter: IP20
200 mA
ETS
software
ETS
software
Scenario 1:
Scenario 2:
3. DIMENSIONS
4. CONNECTION
All the wiring must be carried out with the mains power off.
BUS/KNX - USB
interface
Cat. No. 0 035 47
OR
240
50
147
50
275
BUS/KNX connection
L max = 150 m
max./out
X 32 D
D
100 m 0.5 mm2
150 m 0.75 mm2
300 m 1.5 mm2

Catalogue number(s): 0 488 64
Controller - 4 x DALI circuits -
BUS/KNX
Technical data sheet: S000064192EN-3 Updated: 29/10/2015 Created: 03/05/2012
3/6
CONTENTS
5. INSTALLATION
Mounting
On cable tray
1
3
4
2
1/4
1/4
A W
1
3
2
4
2
2
Using double connector Cat. No. 0 488 68
4. CONNECTION (continued)
Cat. No. 0 488 68
Cat. No. 0 488 72
or
Connects directly to the controller
and/or sensor.

Catalogue number(s): 0 488 64
Controller - 4 x DALI circuits -
BUS/KNX
Technical data sheet: S000064192EN-3 Updated: 29/10/2015 Created: 03/05/2012
4/6
CONTENTS
7. COMMUNICATION OBJECTS
7.1 BUS/KNX ceiling-mounting controllers for dimming
(DALI protocol)
6. PARAMETER SETTING
NB: All the wiring must be carried out with the mains power off.
Switching the controller on generates an automatic configuration.
Configuring the controller means that the wiring can be checked.
Compatible peripheral(s) and the controller recognise one another on
their BUS . All sensors control all loads.
The KNX system must be configured using a PC with ETS software
installed. This means each peripheral can be connected to its load.
Technical documentation regarding KNX product settings is integrated
in the ETS database available from January 2012.
Pro Relations department: 0810 48 48 48 48 (local call rate in
France) Mon-Fri 8 am-6 pm
NB: Addressing the DALI channels
DALI ballast: total lighting of all loads, then gradual dimming and
switching off of the loads in a random order
DSI ballast: addressed automatically when switched on
NOTE: Do not install DSI and DALI ballasts
on the same channel.
Short press < 1 s
1 The LED
flashes slowly
2 The LED
flashes quickly
3The LED goes out
after a few seconds
DALI
or
DSI
Long press = 10 s
Note: All technical information is available at
www.legrandoc.com
Obj. Function Object name Type Flag
0 On/Off NRC Ch1– IN_ON/
OFF
1.001 Switch
(1 bit)
CW
This object is used for On/Off control of luminaires connected to
controller output 1.
1+/- Dimming NRC Ch1 – IN_DIM 3.007 Control_
Dimming (4 bits)
CW
This object is used to vary the light intensity of all luminaires
connected to controller output 1.
2 Value NRC Ch1 – IN_
LEVEL
5.001 Scaling
(1 byte)
CW
This object is used to modify the level of light of all luminaires
connected to controller output 1.
3 On/Off NRC Ch1 – OUT_
ON/OFF_STATUS
1.001 Switch
(1 bit)
CRT
This object gives access to the status of luminaires connected to
controller output 1. A 1-bit status (On/Off) is sent.
4 Value NRC Ch1 – OUT_
LEVEL_STATUS
5.001 Scaling (1
byte)
CRT
This object gives access to the status of luminaires connected to
controller output 1. A status with the value of 1 byte (0…100%) is
sent.
Obj. Function Object name Type Flag
5 Enable/
Disable
NRC Ch1 – IN_
ENABLE/DISABLE
1.003 Enable
(1 bit)
CW
This object is used to block or unblock the output in its present
status. Commands will not be recognised.
14 FAULT NRC Ch1 - OUT_
DALI_DEFAULT
1.002 Boolean
(1 bit)
CRT
This object is used to signal a fault on channel 1 of the DALI bus. If
the object = 1: Fault (short-circuit, ballast communication, lamp) If
the object = 0: No fault
Warning: The fault is generated after the output has been
controlled.
7 Override NRC Ch1 - IN_
OVERRIDE_ON/OFF
– 2 bits
2.001 Switch
Control (2 bits)
CW
This object is used to control the state of controller output 1 with the
concept of priority:
Bits = 01: Output ON
Bits = 00: Output OFF
Bits = 11: Output forced to ON
Bits = 10: Output forced to OFF
Like for objects 0, 1, 2, 3, 4, 5 and 7 assigned to controller output 1,
objects 8, 9, 10, 11, 12, 13 and 15 are assigned to output 2, objects
16, 17, 18, 19, 20, 21 and 23 are assigned to output 3, etc.

Catalogue number(s): 0 488 64
Controller - 4 x DALI circuits -
BUS/KNX
Technical data sheet: S000064192EN-3 Updated: 29/10/2015 Created: 03/05/2012
5/6
CONTENTS
7. COMMUNICATION OBJECTS (continued)
7. COMMUNICATION OBJECTS (continued)
7.2 Peripherals
* The object numbers for the connected peripherals are assigned
dynamically when the ETS project is created.
The object name is preceded by the 8-digit product identifier.
7.2.1 Switch type multifunction control, 1 and 2 way
- Lighting control mode
Obj. Function Object name Type Flag
32 Scenario NRC-IN_RECALL_
SCENARIO
17.001
SceneControl
(1 byte)
CW
This object is used to call scenes which have been configured on the
controller. Up to 32 scenarios can be configured.
Warning: Each controller output can be controlled in a
maximum of 10 scenarios.
67 Scenario NRC OUT_
SCENARIO
17.001
SceneControl
(1 byte)
CRWTU
This object is used to transmit the scenario numbers configured on
the peripherals connected to the controller.
29 SCHEDULE NRC IN_
SCHEDULE_
AUTOMATION
1.003 Enable
(1 bit)
CW
This object is used to block all automated control by sensors
connected to the controller.
If the object = 1: The sensors are inactive
If the object = 0: The sensors control the level of light
6 Fault NRC OUT_BUS_
DEFAUT
1.002 Boolean
(1 bit)
CRT
This object is used to signal a fault on the control bus, a
malfunctioning peripheral or disconnected peripheral.
If the object = 1: Communication fault
If the object = 0: No fault
Obj. Function Object name Type Flag
* On/Off …. Ch1_CMD_OUT_
ON/OFF
1.001 Switch
(1 bit)
CT
This object is used to send the ON/OFF telegram generated by a
short press on the control unit.
*Dimming +/- …. – Ch1_CMD_
OUT_DIM
3.007 Control_
Dimming (4
bits)
CT
This object is used to send the dimming telegram generated by a
long press > 0.5 s on the control unit.
* Value …. – Ch1_CMD_IN_
LEVEL_STATUS
5.001 Scaling
(1 byte)
CRW
This object is used to manage feedback of information about the
control unit.
Byte = 0 blue LED
Byte ≠0 pink LED
* On/Off ….– Ch1_CMD_IN_
ON/OFF_STATUS
1.001 Switch
(1 bit)
CRW
This object is used to manage feedback of information about the
control unit.
Bit = 0 blue LED
Bit = 1 pink LED
Obj. Function Object name Type Flag
* Up/Down …. Ch1_CMD_SHT_
OUT_UP/DOWN
1.008 Up/Down
(1 bit)
CT
This object is used to send the telegram generated by a long press
> 0.5 s on the control unit.
Bit = 0 The shutter goes up
Bit = 1 The shutter goes down
* Step/Stop …. Ch1_CMD_SHT_
OUT_STOP
1.009 Switch
(1 bit)
CT
This object is used to send, with a short press, the Stop telegram if
the shutter is moving and the Step down telegram if the shutter is
stationary.
* Status …. Ch1_CMD_SHT_
IN_POS_STATUS
5.001 Scaling
(1 byte)
CRW
This object is used to manage feedback of information about the
control unit.
Byte = 0 blue LED
Byte ≠0 pink LED
- Shutter control mode
These communication objects are available for each control unit.
Obj. Function Object name Type Flag
* On/Off …. Ch1_CMD_OUT_
ON/OFF
1.001 Switch
(1 bit)
CT
This object is used to send the ON/OFF telegram generated by a
short press on the control unit.
*Dimming +/- …. – Ch1_CMD_
OUT_DIM
3.007 Control_
Dimming (4 bits)
CT
This object is used to send the dimming telegram generated by a
long press > 0.5 s on the control unit.
* Value …. – Ch1_CMD_IN_
LEVEL_STATUS
5.001 Scaling (1
byte)
CRW
This object is used to manage feedback of information about the
control unit.
Byte = 0 blue LED
Byte ≠0 pink LED
* On/Off … .– Ch1_CMD_IN_
ON/OFF_STATUS
1.001 Switch
(1 bit)
CRW
This object is used to manage feedback of information about the
control unit.
Byte = 0 blue LED
Byte = 1 pink LED
Obj. Function Object name Type Flag
* LUX …. – Ch1_OUT_LUX 9.004 Lux
(2 bytes)
CT
This object is used to transmit the level of light measured by the light
level cell (0…65535 lux).
7.2.2 ON/OFF lighting controls, 1 and 2 way
- Lighting control mode
These communication objects are available for each control unit.
7.2.3 Light level measurement cell

Catalogue number(s): 0 488 64
Controller - 4 x DALI circuits -
BUS/KNX
Technical data sheet: S000064192EN-3 Updated: 29/10/2015 Created: 03/05/2012
6/6
CONTENTS
8. CARE
Do not use: acetone, tar-removing cleaning agents or
trichloroethylene.
Resistant to the following products: - Hexane (EN 60669-1)
- Methylated spirit
- Soapy water
- Diluted ammonia
- Bleach diluted to 10%
- Window-cleaning products
9. STANDARDS
Directive: CE
Installation standards: NFC 15-100
Product standards: IEC 60669-2-1
Environmental standards:
- EU Directive 2002/96/EC:
WEEE (Waste Electrical and Electronic Equipment)
- EU Directive 2002/95/EC:
RoHS (Restriction of Hazardous Substances)
- Decrees and/or regulations: Public buildings
Workplace buildings
High-rise buildings
WARNING: Always test before using other special cleaning
products.
7. COMMUNICATION OBJECTS (continued)
7.2.4 Wall-mounting sensors (flush or surface), ceiling-mounting
sensors, surface-mounting sensors
Obj. Function Object name Type Flag
* Presence …. – Ch1_SENSOR_
OUT_OCC/
UNOCC
1.018
Occupancy
(1 bit)
WT
This object is used to send a telegram concerning presence and end
of presence.
If object = 1: Presence detected
If object = 0: End of presence
Warning: End of presence is sent at at the end of the sensor
time delay.
* Presence …. – Ch1_SENSOR_
IN_OCC/UNOCC
1.018
Occupancy
(1 bit)
CWT
This object is used to receive a detection frame from another sensor.
If object = 1: Presence
If object = 0: End of presence
* On/Off …. – Ch1_SENSOR_
OUT_ON/OFF
1.001 Switch
(1 bit)
CT
This object is used to send the ON/OFF telegram to the actuator.
Warning: Whether this object is sent depends on the sensor
parameter setting mode.
* On/Off …. – Ch1_SENSOR_
IN_ON/OFF_
STATUS
1.001 Switch
(1 bit)
CRW
This object is used to feed back the load status for On/Off closed
loop regulation.
Warning: When the Level-Status object is connected, this object
cannot be used.
* Value …. – Ch1_SENSOR_
OUT_LEVEL
5.001 Scaling
(1 byte)
CT
This object is used to check the level of a load as a percentage. This
object is used for dimming regulation (open or closed loop).
* Value …. – Ch1_SENSOR_
IN_LEVEL_
STATUS
5.001 Scaling
(1 byte)
CRW
This object is used to feed back the load status for dimming closed
loop regulation.
Warning: When the ON/OFF-Status object is connected, this
object cannot be used.
* LUX … .– Ch1_SENSOR_
IN_LUX
9.004 Lux (2
bytes)
CRW
This object is used for the link with an external light level cell in the
case of open loop regulation (internal measurement is disabled).
Warning: When the sensor is operating in open loop mode, a
calibration phase with luxmeter is compulsory.
* SYNCHRO-
NISATION
…. – Ch1_SENSOR_
IN_SYNCHRO
1.001 Switch
(1 bit)
CW
This object is used to integrate a manual control in the control loop.
It must be linked to the control object “CH_CMD_OUT_ON/OFF”.
Warning: If the object is not used, following a command the
sensor will always cut off regulation and switch to override
mode.