LEGRAND DRD9 User manual

ADVANCED OPERATION
Groups
You can use the Group feature to control multiple Miro wireless fan controls from
one location. Binding the fan controls together in the same Group enables them to
work in exactly the same way, from any of the control locations.
You can also Group one or more Miro DRD8 Wireless Multilocation Controllers
with a single fan control to control one fan circuit from multiple locations.
You can include other Miro wireless devices in the Group. Just remember that all
devices in the Group operate when one member operates. If you group a dimmer
with a fan control, the fan speed will increase when you increase the brightness
from the dimmer. Conversely, if you press a button on the fan control to reduce the
fan speed, the lights will dim.
Set the House ID (see Set House ID) before setting up Groups.
1. Go to any device that you want to include in the Group. Press . The device
LED flashes yellow. Devices not currently in the group flash green.
You now have 5 minutes to complete this process.
2. To include or exclude a device in the Group press on the device until the
LED changes color. Yellow flashing LED = Included in the Group
Green flashing LED = NOT included in the Group
If you get to a device and it is NOT flashing, see TROUBLESHOOTING.
3. Return to the device used in step 1 and press to terminate Group binding.
All LEDs revert to solid green.
Scene Control
The Miro Wireless Fan Control may be easily incorporated into room and whole
house preset scenes. After binding the fan control to the desired scene, as
described in the scene controller installation instructions (DRD5, DRD6, MRH5G,
or MRH6G) set the fan speed by pressing one of the speed buttons or or .
Note that the DRD6 and MRH6G wireless room scene controllers’ default
operation for the E scene button and the paddle does not turn off the
DRD9 fan control. You can manually add the fan so that it is included when
“all off” function is invoked at the room scene controller.
The Miro Installation Guide provides more information about configuring scenes.
Application support information and the Miro Installation Guide are available
online.

TROUBLESHOOTING
During Set House ID, the LED is not flashing on some wireless Miro devices.
• IfLEDissolidgreenbeforeinitiatingHouseIDbinding:
The device already has another House ID. Reset it to the factory default so
that it can be bound to the desired House ID. Resetting to factory defaults
is described in the “I need to start over” issue.
• IfLEDissolidyellowafterinitiatingHouseIDbinding:
The device may be out of range of the initiating device. Add a MRR2G Miro
Wireless Repeater to boost signal range.
During Binding, all LEDs stop flashing before I am finished.
The binding process timer may have expired. Restart the binding process
timer by repeating steps 1 and 2 of the procedure you were using. Notice
that the devices you previously included are flashing yellow; simply finish the
process from where you left off.
The device LED flashes red when I press .
If house or room scene controllers are used in the house, the house or
room configuration may be locked. Consult the installation instructions for
the DRD5 or MRH5G wireless house scene controller if one is present. See
the DRD6 or MRH6G wireless room scene controller instructions if one is
present.
I made a configuration mistake. I need to start over.
You can reset any Miro wireless device to factory default settings by pressing
and holding until the LED changes to solid yellow (approximately 10
seconds). During the process, the LED flashes yellow and when complete,
it changes to solid yellow. The device can then be reconfigured, exactly like
any new device (see the Set House ID section).
The fan control does not work and the status LED is flashing red
• at2Hz(10timesin5seconds):
The fan control has detected an overload condition and has shut down.
To clear the fault condition, tap and wait for the LED to turn green.
Disconnect loads in excess of rated load and try again.
• at3Hz(15timesin5seconds):
The fan control has detected a short-circuit condition and has shut down.
To clear the fault condition, tap and wait for the LED to turn green.
Remove power, rectify the short-circuit, restore power, and try again.
The status LED is off.
Check the paddle position. If the bottom edge is recessed, the Air Gap safety
feature is engaged. See Fan Maintenance.
CLEANING
Clean using a cloth dampened only with water and a little mild detergent. Use of
solvents or hydrocarbon-based cleaners may cause permanent damage.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmenttoanoutletonacircuitdifferentfromthattowhichthe
receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Caution:Anychangesormodicationstothisdevicenotexplicitlyapprovedby
the manufacturer could void your authority to operate this equipment.
WARRANTY INFORMATION
Manufacturer warranties its products to be free of defects in materials and
workmanshipforaperiodofve(5)years.Therearenoobligationsorliabilities
on the part of manufacturer for consequential damages arising out of, or
in connection with, the use or performance of this product or other indirect
damageswithrespecttolossofproperty,revenueorprot,orcostofremoval,
installation or reinstallation.
Please
Recycle
1061 South 800 East
Orem, UT 84057
Phone:800.555.9891
www.vantagecontrols.com
Legrand Customers contact: Vantage Customers contact:
05761r209/07
301 Fulling Mill Road Suite G
Middletown, PA 17057
Phone:800.321.2343
www.legrand.us/onq

DRD9
Wireless Fan Control
Specifications
Voltage 120VAC,60Hz
Operating Temperature.................32°F to 104°F (0°C to 40°C)
Maximum Load Rating....................................................... 1.5A
Load Type Compatibility.............. Up to two ceiling fan motors
Installation Instructions
U.S. Patent 6,175,220. Other utility,
design, and foreigh patents pending.

UNIT DESCRIPTION
The Miro Decorator DRD9 Wireless Fan Control conveniently offers silent,
one-touch control of one or two ceiling paddle fans, with a combined current
rating up to 1.5 amps. The DRD9 has five buttons to provide 4 speed controls,
plus off. One touch of the rocker paddle can also turn the fan off, or turn it on
and resume the most recently used speed.
Miro Wireless
Miro wireless devices use radio signals to communicate with each other
to control lighting and other types of electric loads in selected areas. They use
the900MHzbandforhigh-speedcontrolcommunication.Usingthepatented
“frequency-agile” Top Dog™ technology, Miro wireless devices
avoidinterferencewithother900MHzdevices,suchascordlessphones
and baby monitors.
INSTALL IN COMPLIANCE WITH ALL APPLICABLE
CODES & STANDARDS.
Failure to follow these instructions may cause
personal injury or equipment damage.
CAUTION
THIS UNIT IS EXCLUSIVELY DESIGNED FOR USE WITH CEILING FANS.
Do not use to control lighting, receptacles
or transformer-operated devices.
Do not use for a fan and a light wired together on the same load wire.
Do not wire in the same circuit as a GFCI circuit breaker or receptacle.

INSTALLATION
For ease of installation, manufacturer recommends use of a deep wall box.
1. Disconnect power to circuit by turning circuit breaker OFF before
installation.
2. Remove existing wall plate and switch.
3. Stripexistingwires1/2”.
4. Connect the supply and load ground wires to the GND terminal on the
back of the unit.
5. Connect the white (Neutral) fan control wire to the white supply and white
load wires, using a wire nut.
6. Connect the black fan control wire to the black supply Line, using a
wire nut.
7. Connect the red fan control wire to the black load wire, using a wire nut.
8. Attach the wall plate.
9. Switch the circuit breaker back ON.
CAUTION
TURN THE POWER OFF AT THE CIRCUIT BREAKER
BEFORE INSTALLING THE FAN CONTROL.

SET HOUSE ID
All Miro wireless devices installed in the same home must acquire the same
unique House ID before use. This process is known as house binding. Each
Miro wireless device is bound to all other Miro wireless devices in the house.
New Installation
1. Withalldevicesinstalledandenergized,makesurethateveryMirowireless
device LED is yellow. If any LED is off, be sure the circuit breaker is on and
the device is correctly installed.
2. Press on any device paddle
until the LED flashes yellow
(about 2 seconds). This indicates
that it has acquired a unique
House ID.
3. Make sure that all other Miro
wireless device LEDs are flashing
green, indicating that they have
acquired the same House ID.
4. Return to the device used in step 2, which is still flashing yellow. Press
until the LED changes to solid green (about 2 seconds). All device LEDs in
the house change to solid green, indicating house binding is complete.
Adding a Device to an Existing Installation
If you’re adding or replacing a device in a Miro wireless installation that is
already operating, the new device must acquire the same House ID as the
other Miro wireless devices in the house. After the new device is powered up,
the LED should be solid yellow. This indicates that it has not yet acquired a
HouseID.ToacquiretheHouseIDfortheexistingsystem:
1. Press on any previously bound device until the LED flashes yellow (about
2 seconds).
2. VerifythatthenewlyaddeddeviceLEDisashinggreen,indicatingthatit
has acquired the House ID.
3. Return to the same previously bound device used in step 1 and press until
the LED changes to solid green (about 2 seconds). All device LEDs should
now be solid green.
When you see
in the instructions,
firmly press and
hold both the top
and bottom of the
device paddle until
the LED changes
(about 2 seconds).

OPERATION
Beforeuse,setthefantorunintheappropriatedirectionandatfullspeed:
1. Press the top speed button on the DRD9 wireless fan control, and wait to
allow the fan motor to run up to full speed.
2. Using the controls on the fan (typically pull-chains), adjust so that the fan is
running at full speed, and in the desired direction. The pull chains may now
be removed or shortened.
Button and Paddle Functions
The DRD9 wireless fan control has a rocker paddle
andvespeedcontrolbuttons.Usethespeedbuttons
to select an appropriate fan speed or OFF.
Rocker paddle functions are described below.
When you see
touch the top
of the paddle as
directed.
Fastest
Slowest
OFF
The wireless fan control may feel warm to the touch during normal operation.
Fan Maintenance
When fan maintenance is required, use the Air Gap Isolation feature for safety.
Toactivatethefeature:
Press FIRMLY, so that the paddle clicks and latches in. Make sure the
status LED is extinguished, indicating that the load is isolated.
To release and return to normal operation, press .
Power Fail Memory
After a power failure, all Miro devices automatically return to the state they
were in immediately prior to loss of power.
Tap once Turn fan ON and resume the last used speed
Tap twice Full speed
– – Press and hold Increase the speed
Tap once Turn fan OFF
– – Press and hold Decrease the speed
When you see
touch the
bottom of the
paddle as
directed.

4-FOLD
•Print:2-sides
•InkColor:Black
•Paper:White16lb(60g/msq)
Uncoated, prefer recycled stock
•Finaltrimsize:16”(Wide)x6”(High).
•Four(4)fold.
•Finalfoldedsize:4”(Wide)x6”(High).
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
SANTA CLARA, CALIFORNIA
Title: DRD9 Installation Instructions
IFYOUHAVEANYQUESTIONSREGARDINGSPECIFICATIONSORREQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Mary Jo Sowinski.
Phone:408-486-7511
Email:[email protected]
Drawing #:
05761
Orig. Drawing Date: 10 AUG 06 Rev. #:
2
Revision Date: 25 SEP 07
REVEL
Scale: 1:1
All information in this drawing is the property of Watt Stopper/Legrand and cannot be copied or
used without the written approval of Watt Stopper/Legrand.
Drawn by
PLM
MarCom
Engineering
QA
TITLE BOX PG
REV DESCRIPTION INT: REV. DATE APPROVED
1 ECO#C01694 MJS 3/31/04 CG
2 EC0# C02414 DR