LEGRAND HPM Inspire RCF12H4WE User manual

Warranty
Legrand warrants this product for a period of 3 years from the date of purchase.
These goods come with guarantees that cannot be excluded under the Australian and
New Zealand Consumer Laws. You are entitled to a replacement or a refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
See the Warranty card enclosed with this product for further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
LE11531AH
Product Notes
1. This product must be installed by a licensed electrician and used as
per these instructions.
2. This product contains no serviceable parts and no attempt should
be made to repair this product. If the product is faulty it should be
discarded.
3. This product must be cleaned periodically with a damp cloth.
Cleaning agents and solvents should never be used.
4. This product has been designed to operate in ambient temperatures
between 5°C to 40°C.
5. This product must be securely attached to a structural member for
support. Fixing means (hooks & brackets) must be fixed to the
structural member with sufficient strength to withstand 4 times the
weight of the ceiling fan.
6. During installation the mains supply wiring terminals should be
tightened between 0.4Nm and 0.6Nm. Over-tightening may damage
the terminal. Under-tightening may result in hot joints.
7. This product is for Indoor use only. This product is not intended to
be exposed to direct weathering. It is not suitable for installation
in hazardous and/or corrosive areas. It is not suitable for marine
environments such as areas subjected to salt spray and/or mist.
8. This product is not intended for use by young children or infirm
persons without supervision. Young children should be supervised to
ensure that they do not play with the appliance.
9. Extended exposure to UV rays (such as exposure to direct sunlight)
may cause discolouration of this product.
10. The material in this product may vary in colour from batch to batch.
Colour matching from one batch to another cannot be guaranteed.
11. This product has been designed to operate on a nominal supply
voltage of 230V - 240 V a.c. 50Hz.
12. After installation this product must be tested as required by the
appropriate government and/or statutory regulations.
13. This product utilises intellectual property in the form of registered
designs, trademarks, and/or patents. Such intellectual property
remains the property of Legrand in all cases.
14. Legrand reserves the right to modify the specification of this product
at any time.
Legrand Australia
1300 369 777
www.hpm.com.au
Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
Inspire Ceiling Fans Weight
RCF12H4WE Inspire Ceiling Fan Plywood, 4 Blades, 1220 mm, 48“, Hangsure - White 5.6 kg
RCF12H4BL Inspire Ceiling Fan Plywood, 4 Blades, 1220 mm, 48“, Hangsure - Black 5.6 kg
RCF12H4BS Inspire Ceiling Fan Plywood, 4 Blades, 1220 mm, 48“, Hangsure - Silver 5.6 kg
Inspire Ceiling Fan Plywood
Cat. No: RCF12H4WE, RCF12H4BL, RCF12H4BS
Instruction Sheet
4-Blade Models
PLEASE READ ALL INSTRUCTIONS CAREFULLY. RETAIN FOR FUTURE REFERENCE. INSTALLATION MUST BE CARRIED OUT BY A LICENSED
ELECTRICAL CONTRACTOR.
1 Fix fan blades to motor assembly
Max torque 0.5Nm
Magnetic Screw driver should be used
x4
x3
x 2
A. Assemble the blades to the motor with the
screws supplied (3 x screws per blade).
B. Assemble the cover plate to the motor housing with
2 x screws provided. Max. torque to 0.5 Nm.
1. The Hang-sure style is suitable for both flat and inclined ceilings (up to maximum angle of 20°).
2. This fan has been supplied with a 3-speed fan controller. It is designed to operate a single fan only.
3. The fan is to be installed so that the fan blades are more than 2.1m above floor level. Fan blades should have clearances >300mm
from any obstacles.
4. During installation a switch disconnection should be incorporated in the supply circuit (switch supplied).
5. Cable connectors on the Remote Control kit are not compatible with the connector on the fan and must be manually terminated
(If installing HPM Remote Control kit).
6. Blades provided are paired for individual fan and must not be mixed with blades from other fans. This may affect performance and
cause vibration/wobble. If unusual oscillating movement is observed, stop using the ceiling fan immediately and contact Legrand
Australia, its service agent or a suitably qualified person.
Important considerations
Quick- connect wiring
Box Contents
•Motor assembly
• 4 blades
• 3-speed fan controller
• Mounting Bracket
• 2 x screws and lugs for bracket
• 12 x screws for blades
• Cover plate and screws
• Instruction Sheet
09 / 2022
Specifications
Motor 50 W
1
4
Paper

Hang-Sure Mounting
Fix mounting bracket (supplied) firmly to timber or concrete.
4
5
Hanging the fan on the bracket
Connect the quick connectors
Hang-Sure Bracket
Hang the fan on the bracket. Ensure bracket guide pin is fitted into slot on ball joint and that all wires are clear of the ball joint.
Click the quick connect plug into the socket connector from the fan.
N
L
A. Connect supply wiring to the terminal block provided.
Refer to instructions for Remote Control Kits (CFREMOTEH) for installation and mounting requirements.
Hang-Sure Canopy
Tighten with 4 screws to the bracket. Make sure wires are not trapped in between.
6 Slide upper canopy into position and secure
2
3
Fixing of mounting bracket to ceiling
Supply connection to fan
Select a suitable location for the fan. Use the 2 coach screws provided (or similar) to make an attachment to a solid structural member.
Ensure the mounting method is capable of supporting a hanging weight of 30 kg.
N
L
N
L
Bracket
Supply wiring
Guide
pin
Slot
N
L
x 2 Screws
x 2 Screws
L
RCFL12H4WE only
RCF12H4 Series
23
The HPM ceiling fan comes complete with a capacitive 3-speed controller on a wall plate with standard 84mm fixing centres. Please
refer to instructions supplied with the speed controller for installation.
Connecting the speed controller7
3 - Speed fan controller (ED3FCWE)
RCF12H4 Series
■ If intending to use a Remote Control kit (not supplied)
then do not mount this wall plate.
■It is recommended to install a wall switch instead.
“IF INSTALLING A REMOTE CONTROL, IT MUST BE INSTALLED IN CONJUNCTION WITH A WALL SWITCH TO ISOLATE POWER.”