LEM 602SS Parts list manual

LEM Products • 109 May Drive, Harrison, OH 4 030 • PH: 1-877- 36-7763 • www.lemproducts.com
PLEASE READ BEFORE OPERATING EQUIPMENT
LEM Products • 109 May Dr ve, Harr son, OH 45030
1-877-536-7763 • www.lemproducts.com
I
IN NS ST TR RU UC CT TI IO ON NS S
F
FO OR R L LE EM M M ME EA AT T
T
TE EN ND DE ER RI IZ ZE ER R
M
MO OD DE EL L: :
6
60 02 2S SS S
TO INSTALL TENDERIZER ATTACHMENT:
1. Align the drive shaft of the motor with the hub (#9) and drive shaft (#11) of the tenderizer and
tighten the star bolt (#1 ) securely.
2. Insert the two meat combs (#1) into the slots in the top of the upper housing (#3) – one comb
on each side of the chute. The combs should slide easily into the holes between the drive and
drive shafts. When inserted properly the combs will be visible from the bottom of the lower case
(#8). If, when in use, the meat is wrapping around the knives and rollers the combs are not
inserted properly.
• Turn unit off and remove plug from wall outlet.
• Remove combs.
• Unscrew thumbscrews.
• Carefully remove wrapped meat from rollers.
• Reassemble tenderizer and insert combs following above directions. Sometimes switching the
combs to the opposite side helps.
• Plug in tenderizer and continue.
TO CLEAN:
1. Turn unit off and remove plug from wall outlet.
2. Remove tenderizer attachment from grinder by loosening star bolt (#1 ).
3. Remove meat combs (#1).
4. Remove thumbscrews (#2).
. Remove upper case (#3).
6. Remover the drive and driven cutter shafts.
7. Wash with hot soapy water. Rinse and dry parts thoroughly. (Since meat will ultimately
get between the knives and the spacers, occasionally the drive and driven units should be
disassembled, and each piece washed thoroughly. Start disassembly by removing the C-Clip
(#1 ) on the end opposite the gear. When reassembling the drive unit, start with a single
spacer, and end with a two spacers. When reassembling the driven shaft, start with a two
spacers, and end with a single spacer. Also note that each cutter blade has a single notch
in the square portion. Make sure these notches lineup on the shaft. Doing this will assure
that the blades all line up correctly.) A video of the reassembly process may be viewed
at the lemproducts.com.
8. To reassemble,
• Put the drive cutter shaft (#13) roller into position first.
• Put the driven cutter shaft (#4) roller into position next.
• Make sure the gears (#14) are properly aligned and mesh.
• Replace upper case (#3) and secure with thumbscrews (#2).
LEM Products offers accessories to attach to the 602SS motor: 25 lb. Meat Mixer and
a #8 Grinder it. Please call 1-877-536-7763 to purchase additional products or to
request a free catalog.

LEM Products • 109 May Drive, Harrison, OH 4 030 • PH: 1-877- 36-7763 • www.lemproducts.comLEM Products • 109 May Drive, Harrison, OH 4 030 • PH: 1-877- 36-7763 • www.lemproducts.com
2 3
SAFETY INSTRUCTIONS
Important: Thoroughly hand clean all parts before first use in warm soapy water, to remove the
lubricant applied during manufacturing. Rinse and dry thoroughly.
Read these instructions before operating meat tenderizer.
1. Remove the tenderizer attachment from the motor when not in use.
2. Never operate unit without the cover being in place. The rolling action of the knives could
pull fingers and hands into the knives and cause serious injury.
3. Never leave tenderizer unattended when in use or plugged in.
4. Keep ut f reach f children.
. Drop meat through the opening of the cover. DO NOT attempt to force meat into the opening.
Rolling action of the knives will carry appropriately sized portions of meat into the unit.
6. Use boneless cuts of meat only. Meat should not exceed ¾” in thickness. Remove gristle before
tenderizing to eliminate clogging or stalling. To experience the maximum tenderness, run meat
through tenderizer twice at 90 degree angles. KEEP HANDS A SAFE DISTANCE FROM THE
EXPOSED BLADES ON THE BOTTOM OF THE UNIT.
5
14
17
7
6
7
16
7
11
12
8
10
9
15
17
17
7
17
13
16
515
7
4
17
7
3
2
1
PARTS LIST FOR 602SS MOTOR
PARTS LIST FOR 602SS MEAT TENDERIZER
# Description Q’ty
1 Combs 2
2 Thumb Screw 2
3 Upper Case 1
4 Driven Cutter Shaft 1
Sleeves 4
6 Knife 30
7 Spacer 62
8 Lower Case 1
9 Hub 1
# Description Q’ty
10 Hub Screw 2
11 Drive Shaft 1
12 Connect Screw 1
13 Drive Cutter Shaft 1
14 Gear 2
1 C Ring 4
16 E Ring 4
17 Stainless Steel Washers 6
# Description Q'ty
1 Star Bolt 1
16 Allen Screws M6 for Front Panel 4
17 Front Panel 1
18 Grease Seal 1
19 Roller Bearing 1
20 Main Washer 1
21 Main Gear 1
22 Bearing 3
23 Rubber Pad 1
24 Screws 10
2 S/S Upper Housing 1
26 Handle Screw 2
27 Handle 1
28 Back Panel 1
29 Circuit Breaker 1
# Description Q'ty
30 Fastener for the Power Cord 1
31 Power Cord 1
32 Brace 1
33 Allen Screw M6 for Brace 2
34 S/S Lower Housing 1
3 Switch 1
36 Plastic Feet 4
37 Allen Screw M4 6
38 Phillips Screw M4 for Feet
39 Step Gears 1
40 Clip Spring 1
41 Pinion Gear 1
42 Front Panel of the motor 1
43 Electric Box 1
44 Motor 1