Lenze E931E Series User manual

GHB 13.0001−EN
.88$
Ä.88$ä
Hardware Manual

E931Ex
Servo inverters for extra−low voltages
efesotomasyon.com - Lenze

Please read these instructions before you start working!
Follow the enclosed safety instructions.
efesotomasyon.com - Lenze

Overview
931E−002.iso
efesotomasyon.com - Lenze


4 GHB 13.0001−EN EN 3.0
This documentation is valid for ...
931 ... servo inverters as of nameplate data:
931E_008
  
93 1 E x K 1 0 2.0 3.2
Product range
930
Size/power range
1 = up to 600 W
Design
E = built−in unit for IP 20 control cabinet
Communication
C =
P =
CAN bus integrated
PROFIBUS integrated
Voltage class
K = design for low voltage
Options
1 = with digital inputs and outputs
with analog inputs and outputs
Installation
0 = installation in control cabinet
Hardware version
Software version
efesotomasyon.com - Lenze

5
GHB 13.0001−EN EN 3.0
Key for the overview
View from the front
Pos. Description
X1 RS232
X5 Digital inputs and outputs / analog inputs and outputs
X6 Slot for multimedia memory card
931EC ˘ View from above
Pos. Description
X2 Voltage supply
X4.1
X4.2 CAN interfaces
X10 Digital frequency interface
931EP ˘ View from above
Pos. Description
X2 Voltage supply
X4.1/X4.2 PROFIBUS interface
X10 Digital frequency interface
View from below
Pos. Description
X3 Motor connection
X7 Resolver input
X8 SinCos encoder input
LED Colour State Note
State Green on The control is correctly supplied by a 24 V control voltage, the drive is ready for operation.
blinking Data is written on or read from the memory card.
off No voltage
Power Yellow on The power section is enabled, the motor is supplied with voltage. The drive works with the set
control.
off The drive does not work, the output stage is inactive.
Error Red off No fault
blinking Internal drive error 1)
After the cause of the error has been eliminated, you have to acknowledge the error message:
lEither by using the parameterisation software, or via an edge at DIN9 (controller enable).
lIf no error is active anymore, the LED goes out.
Green
Yellow
Red
on lThe drive is in the initialisation phase after the control voltage has been switched on.
lA new firmware is being installed.
1) Detailed description of the blink codes: 40
Note!
The light−emitting diode "Error" constantly blinks if a fault is active:
ƒIt only displays one fault at a time.
ƒIf several faults are active at the same time, the fault that occured first is displayed.
efesotomasyon.com - Lenze


6 GHB 13.0001−EN EN 3.0
What is new, what has changed ?
Material No. Version Description
.88$ 3.0 12/2007 TD35 Advanced by the 931EP (PROFIBUS) device variant
13058894 2.0 08/2005 TD09 Complete revision for the series
− 1.0 03/2003 LKA Preliminary version
0Fig. 0Tab. 0
Tip!
Current documentation and software updates concerning Lenze products can be found on
the Internet in the "Services & Downloads" area under
http://www.Lenze.com
© 2007 Lenze GmbH & Co KG Kleinantriebe, Hans−Lenze−Straße 1, D−32699 Extertal
No part of this documentation may be reproduced or made accessible to third parties without written consent by Lenze GmbH &
Co KG Kleinantriebe.
All information given in this documentation has been selected carefully and complies with the hardware and software described.
Nevertheless, discrepancies cannot be ruled out. We do not take any responsibility or liability for any damage that may occur.
Necessary corrections will be included in subsequent editions.
efesotomasyon.com - Lenze

Contents i
7
GHB 13.0001−EN EN 3.0
1 Preface and general information 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 About this Manual 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Terminology used 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Scope of supply 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Legal regulations 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Safety instructions 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 General safety and application notes for Lenze controllers 11. . . . . . . . . . . . . . . . . .
2.2 Residual hazards 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Definition of notes used 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Technical data 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 General data and operating conditions 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Rated data 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Communication 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1 Controller with CAN bus 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Controller with PROFIBUS 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Mechanical installation 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Important notes 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Dimensions 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Mounting clearance 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Electrical installation 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Important notes 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Installation according to EMC (installation of a CE−typical drive system) 21. . . . . . .
5.3 Voltage supply 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4 Motor connection 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5 Control terminals 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6 Feedback connection 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.1 Resolver at X7 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.2 SinCos encoder at X8 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7 Communication 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.1 Connection of digital frequency coupling at X10 29. . . . . . . . . . . . . . . . . . .
5.7.2 Connection of CAN bus at X4.1 and X4.2 30. . . . . . . . . . . . . . . . . . . . . . . . .
5.7.3 Connection of PROFIBUS 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.4 Connection of RS232 serial interface to X1 31. . . . . . . . . . . . . . . . . . . . . . . .
6 Commissioning 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Before switching on 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Initial switch−on 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
efesotomasyon.com - Lenze

Contentsi
8 GHB 13.0001−EN EN 3.0
7 Troubleshooting and fault elimination 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Status of the drive 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Error message 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Accessories 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 System cables and plugs 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Power supply units 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3 Memory cards 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4 Motors for 931E servo inverters 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.1 General data and operating conditions 44. . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.2 Rated data 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.3 Mechanical data 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Index 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
efesotomasyon.com - Lenze

Preface and general information
About this Manual
1
9
GHB 13.0001−EN EN 3.0
1 Preface and general information
1.1 About this Manual
Target group
This manual addresses to all persons designing, mounting, commissioning and setting the
servo inverters of the 931 series.
Together with the catalogue, it presents the project documents for the mechanical
engineer and the system engineer.
Contents
The manual complements the mounting instructions included in the scope of supply:
ƒThe features and functions are described in detail.
ƒIt provides detailed information on the possible applications.
ƒThe parameter setting is clarified by examples.
ƒIn case of doubt, the supplied mounting instructions always apply.
Finding information
ƒVia the contents and index, you quickly find the information regarding a specific
problem.
ƒDescriptions and data with regard to other Lenze products can be gathered from the
respective catalogues, Operating Instructions, and Manuals.
ƒYou can request Lenze documentation from your responsible Lenze sales partner, or
download it from the Internet as a PDF file.
1.2 Terminology used
Term In the following text used for
Controller 931E servo inverter
Device 931E servo inverter
Drive 931E servo inverter with connected motor
SDC »Small Drive Control« parameterisation software
efesotomasyon.com - Lenze

Preface and general information
Scope of supply
1

10 GHB 13.0001−EN EN 3.0
1.3 Scope of supply
ƒ931E servo inverter
ƒMounting instructions
After receipt of the delivery, check immediately whether the items delivered match the
accompanying documents. Lenze does not accept any liability for deficiencies claimed at
a later date.
Claim
ƒvisible transport damage immediately to the forwarder.
ƒvisible deficiencies / incompleteness immediately to your Lenze representative.
1.4 Legal regulations
Labelling Nameplate CE identification Manufacturer
Lenze drive controllers are
definitely identified by the
contents of the nameplate.
In compliance with the EC
Low−Voltage Directive
Lenze GmbH & Co KG
Kleinantriebe
Postfach 10 13 52
D−31763 Hameln
Application as
directed
931E servo inverters
lmust only be operated under the operating conditions prescribed in these Instructions.
lare components
– for open and closed loop control of variable speed drives with synchronous motors.
– for installation in a machine
– for assembly with other components to form a machine.
lare electric units for the installation into control cabinets or similar closed electrical operating areas.
lcomply with the requirements of the Low−Voltage Directive.
lare not machines for the purpose of the Machinery Directive.
lare not to be used as domestic appliances, but only for industrial purposes.
Drive systems with 931E servo inverters
lcomply with the EMC Directive if they are installed according to the guidelines of CE−typical drive systems.
lcan be used
– for operation on public and non−public mains
– for operation in industrial premises.
lThe user is responsible for the compliance of his application with the EC Directives.
Any other use shall be deemed as inappropriate!
Liability lThe information, data, and notes in these instructions met the state of the art at the time of printing.
Claims on modifications referring to controllers which have already been supplied cannot be derived from
the information, illustrations, and descriptions.
lThe specifications, processes, and circuitry described in these Instructions are for guidance only and must
be adapted to your own specific application. Lenze does not take responsibility for the suitability of the
process and circuit proposals.
lLenze does not accept any liability for damage and operating interference caused by:
– disregarding the Operating Instructions
– unauthorised modifications to the drive controllers
– operating errors
– improper working on and with the drive controllers
Warranty lTerms of warranty: see Sales and Delivery Conditions of Lenze GmbH & Co KG Kleinantriebe.
lWarranty claims must be made to Lenze immediately after detecting the deficiency or fault.
lThe warranty is void in all cases where liability claims cannot be made.
efesotomasyon.com - Lenze

Safety instructions
General safety and application notes for Lenze controllers
2
11
GHB 13.0001−EN EN 3.0
2 Safety instructions
2.1 General safety and application notes for Lenze controllers
(in accordance with Low−Voltage Directive 2006/95/EC)
For your pesonal safety
During operation, Lenze controllers (frequency inverters, servo inverters, DC speed
controllers) and their corresponding components can be live, moving and rotating
according to their degree of protection. Surfaces can be hot.
Non-authorized removal of the required cover, inappropriate use, incorrect installation or
operation creates the risk of severe injury to persons or damage to material assets.
Additional information can be obtained from the documentation.
High amounts of energy are released in the controller. Thus, it is required to always wear
a personal protective equipment (body protection, headgear, eye protection, ear
protection, hand guard).
All operations concerning transport, installation, and commissioning as well as servicing
must be carried out by qualified, skilled personnel only (IEC 364 and CENELEC HD 384 or
DIN VDE 0100 and IEC−Report 664 or DIN VDE 0110. National regulations for the
prevention of accidents must be observed.).
According to this basic safety information, skilled personnel are persons who are familiar
with the installation, mounting, commissioning, and operation of the product and who
have the necessary qualifications for their occupation.
Application as directed
Drive controllers are components designed for the installation in electrical systems or
machinery. They must not be used as household appliances. They are intended exclusively
professional and commercial purposes according to EN 61000−3−2.
When installing the controllers into machines, commissioning (i.e. starting of operation as
directed) is prohibited until it is certain that the machine complies with the regulations of
EC Directive 98/37/EC (Machinery Directive). EN 60204 must be observed.
Commissioning (i.e. starting of operation as directed) is only allowed when there is
compliance with EMC Directive (89/336/EEC).
The controllers meet the requirements of the Low-Voltage Directive 2006/95/EC.
The technical data and information on the connection conditions can be obtained from the
nameplate and the documentation. They must be followed in any case.
Warning: Drive controllers are products with restricted availability according to
EN 61800−3. These products can cause radio interferences in residential areas. In this case,
special measures are required.
Transport, storage
Please observe the notes on transport, storage and appropriate handling.
Observe the climatic conditions according to the technical data.
efesotomasyon.com - Lenze

Safety instructions
General safety and application notes for Lenze controllers
2

12 GHB 13.0001−EN EN 3.0
Installation
The controllers must be installed and cooled according to the instructions given in the
corresponding documentation.
Ensure proper handling and avoid mechanical stress. Do not bend any component and do
not change any insulation distance during transport or handling. Do not touch any
electronic component or contact.
Controllers contain electrostatically sensitive components which can easily be damaged
by inappropriate handling. Do not damage or destroy any electrical component since doing
so might endanger your health!
Electrical connection
When working on live controllers, the valid regulations for the prevention of accidents (e.g.
VBG 4) must be observed.
The electrical installation must be carried out according to the appropriate regulations
(e.g. cable cross/sections, fuses, PE connection). Additional information can be obtained
from the documentation.
The documentation contains information concerning installation in compliance with EMC
(shielding, earthing, filter arrangement, and cable installation). These notes must also be
observed for CE−marked controllers. The manufacturer of the system or machine is
responsible for ensuring compliance with the limit values demanded by the EMC
legislation. The controllers must be installed in housings (e.g. control cabinets) to comply
with the limit values for radio interferences valid at the site of installation. The housings
must enable an EMC−compliant installation. Make sure in particular that e.g. the control
cabinet doors have a circumferential metal connection to the housing. Reduce housing
openings and cutouts to a minimum.
Operation
If necessary, systems including controllers must be equipped with additional monitoring
and protection devices according to the valid safety regulations (e.g. law on technical
equipment, regulations for the prevention of accidents). You are allowed to adapt the
controllers to your application. Please observe the corresponding information given in the
documentation.
After the controller has been disconnected from the voltage supply, all live components
and power connections must not be touched immediately because capacitors can still be
charged.
All protection covers and doors must be kept shut during operation.
Maintenance and servicing
The controllers do not require any maintenance if the prescribed conditions of operation
are observed.
If the ambient air is polluted, the cooling surfaces of the controller may contaminate, or the
air vents of the controller may be blocked. Therefore, the cooling surfaces and air vents
must be cleaned periodically under these operating conditions. Do not use sharp or
pointed tools for this purpose!
Waste disposal
Recycle metal and plastic materials. Assembled PCBs must be disposed of professionally.
The product−specific safety and application notes given in these instructions must be
observed!
efesotomasyon.com - Lenze

Safety instructions
Residual hazards
2
13
GHB 13.0001−EN EN 3.0
2.2 Residual hazards
Protection of persons
After power−off, the power terminals UL, BR and GND still carry hazardous voltages for at
least 3 minutes!
ƒBefore working on the controller, check that no voltage is applied to the power
terminals.
ƒAlways protect the power terminals against contact.
The discharge current to ground (PE) is > 3.5 mA, according to EN 50178.
ƒIf a fixed installation is required, design the PE conductor with a cable cross−section
of at least 1.5 mm2or use a design with double PE conductor.
Make sure that cables are installed correctly, and that bolted connections and plug
connections are faultless.
Due to the high currents with regard to low−voltage applications, current−carrying parts
can be strongly heated.
Device protection
ƒConnect or disconnect all pluggable terminals in a deenergised state only!
ƒA cyclic connection and disconnection of the supply voltage can overload and
destroy the input current limitation of the drive controller:
– When effecting a cyclic switching of the supply voltage over a longer period, the
period between two switch−on processes at least has to be one minute!
Motor protection
Drive systems can reach dangerous overspeeds (e.g. setting of high field frequencies for
motors and machines which are not qualified for this purpose):
ƒThe controllers do not offer any protection against these operating conditions. Use
additional components for this.
Protection of the machine/system
A missing or incorrect resolver adjustment can bring about undefined control states. The
perfect operation is no longer guaranteed.
efesotomasyon.com - Lenze

Safety instructions
Definition of notes used
2

14 GHB 13.0001−EN EN 3.0
2.3 Definition of notes used
The following pictographs and signal words are used in this documentation to indicate
dangers and important information:
Safety instructions
Structure of safety instructions:
Danger!
(characterises the type and severity of danger)
Note
(describes the danger and gives information about how to prevent dangerous
situations)
Pictograph and signal word Meaning
Danger!
Danger of personal injury through dangerous electrical voltage.
Reference to an imminent danger that may result in death or
serious personal injury if the corresponding measures are not
taken.
Danger!
Danger of personal injury through a general source of danger.
Reference to an imminent danger that may result in death or
serious personal injury if the corresponding measures are not
taken.
Stop!
Danger of property damage.
Reference to a possible danger that may result in property damage
if the corresponding measures are not taken.
Application notes
Pictograph and signal word Meaning
Note! Important note to ensure troublefree operation
Tip! Useful tip for simple handling
Reference to another documentation
efesotomasyon.com - Lenze

Technical data
General data and operating conditions
3
15
GHB 13.0001−EN EN 3.0
3 Technical data
3.1 General data and operating conditions
Conformity CE 2006/95/EC Low-Voltage Directive
Regulations EN 61800−3 Interference level B
Climatic conditions Air humidity max. 90 % without condensation
Cooling Passively via housing surface and rear panel
Admissible temperature range
Transport −25 °C... +70 °C
Storage −25 °C... +70 °C
Operation 0 °C ... +50 °C above +40 °C, reduce the power by 20 W/°C
Permissible installation height 0 ... 1000 m amsl above 1000 m amsl, reduce the rated output
current by 5 %/1000 m
Mounting position Vertical
Installation clearances
above/below ³100 mm
sidewise Directly alignable
Monitoring Overvoltage / undervoltage in the DC bus, overcurrent or short
circuit of the output stage, motor temperature and output stage
temperature, I2xt−monitoring of the motor, encoder monitoring
Type of protection IP 20
Inputs 6 digital inputs, 2 analog inputs
(adjustable via software)
Outputs 2 digital outputs, 2 analog outputs
(adjustable via software)
Memory cards Multimedia card
efesotomasyon.com - Lenze

Technical data
Rated data
3

16 GHB 13.0001−EN EN 3.0
3.2 Rated data
Supply voltage
Rated voltage 24V DC 48V DC
Permissible range 19.2 V DC − 0 % ... 57.6 V DC + 0 %
Supply current at rated power approx. 13 A
Max. supply current 35 A
Rated power 310 W 620 W
Efficiency up to 95 %
PWM frequency (switchable) 10 kHz 20 kHz 10 kHz 20 kHz
Rated output current 0 ... 13 Aeff 0 ... 10 Aeff 0 ... 13 Aeff 0 ... 10 Aeff
Output surge current for 2 s 32 Aeff 25 Aeff 32 Aeff 25 Aeff
Rated output voltage 0 ... 14 Veff 0 ... 27 Veff
Output frequency 0 ... 200 Hz
Control voltage 1) 24 V DC ±20 %
Control current min. 0.25 A (control section only)
max. 1.5 A (all outputs connected)
Brake chopper switching threshold
On approx. 63 V DC
Off approx. 60 V DC
Overvoltage monitoring switching threshold approx. 70 V DC
Internal brake resistor
Resistance R 17 W
Permanent power PN10 W
Peak power Ppulse 200 W for 50 ms
External brake resistor
Resistance R > 5 W
Permanent power PN10 ... 600 W
Motor holding brake 24 V / 1 A
Positioning range ± 219 revolutions
Savable positions 64
Scanning times of the control loops
Current controller 100 ms
Speed controller 200 ms
Position controller 400 ms
1) Observe minimum voltage of the brake!
efesotomasyon.com - Lenze

Technical data
Communication
Controller with CAN bus
3
17
GHB 13.0001−EN EN 3.0
3.3 Communication
3.3.1 Controller with CAN bus
Area Values
Communication profile DS 301, DSP 402
Communication medium RS232
Network topology Without repeater: line / with repeaters: line or tree
CAN node Slave
Baud rate (in kbps) 10, 20, 50, 100, 125, 250, 500
Maximum cable length per bus
segment
1200 m (dependent on baud rate and cable type used)
Bus connection RJ45
3.3.2 Controller with PROFIBUS
Area Values
Communication profile
(DIN 19245 part 1 and part 3)
PROFIBUS−DP−V0
Communication medium RS485
Drive profile PROFIdrive
Network topology Without repeater: line / with repeaters: line or tree
PROFIBUS−DP station Slave
Baud rate [kbps] 9.6 ... 12000
Maximum cable length per bus
segment
1200 m (dependent on the baud rate and cable type used)
Bus connection X4.1, X4.2 9−pin Sub−D socket
efesotomasyon.com - Lenze

Mechanical installation
Important notes
4

18 GHB 13.0001−EN EN 3.0
4 Mechanical installation
4.1 Important notes
ƒUse the controllers as built−in units only!
ƒIn case of contaminated cooling air (dust, lints, greases, aggressive gases):
– Take suitable preventive measures, e.g. separate air duct, installation of filters,
regular cleaning, etc.
Stop!
Do not install drives on top of each other in the control cabinet!
ƒObserve installation clearances!
– You can install several controllers next to each other without free space in a
control cabinet.
– Ensure unimpeded ventilation of cooling air and outlet of exhaust air!
– Allow a free space of 100 mm at the top and at the bottom.
– If possible, the rear panel of the drive controller should be provided with a good
thermal connection to the control cabinet wall.
– In case of high load and a bad heat dissipation, the drive controller reduces the
drive power, or possibly switches off.
ƒDo not exceed the range of the ambient operation temperature specified in the
Technical Data.
ƒIn case of permanent oscillation or agitation:
– Check whether shock absorbers are necessary.
Possible mounting positions:
Vertically on the control cabinet rear panel with mains terminals at the top.
efesotomasyon.com - Lenze

Mechanical installation
Dimensions
4
19
GHB 13.0001−EN EN 3.0
4.2 Dimensions
931E−006.iso
Fig. 1 Drive dimensions
4.3 Mounting clearance
931E−007.iso
Fig. 2 Installation clearances
efesotomasyon.com - Lenze

Electrical installation
Important notes
5

20 GHB 13.0001−EN EN 3.0
5 Electrical installation
5.1 Important notes
Stop!
The drive controller contains electrostatically sensitive components.
The personnel must be free of electrostatic charge when carrying out assembly
and service operations.
Danger!
ƒThe connection of all pluggable terminals has to be effected in a
deenergised state.
ƒConnecting and disconnecting the voltage supply (X2) due to the charging
processes of the DC bus capacitor may cause traces of burning on the
plug−in connection, and may result in a destruction of the internal electronic
circuit.
ƒA false polarity of the DC supply can bring about the destruction of the
drive. Before switching the drive on, ensure that the polarity of the
DC supply is correct.
Note!
The following requirements have to be met with regard to the trouble−free
operation:
ƒAn installation according to EMC.
ƒThe shield of the motor cable has to be applied to PE potential on a
preferably large surface in order to prevent negative effects.
ƒThe resolver cable, encoder cable, and the motor cable may have a
maximum length of 15 m!
ƒThe feeding power supply units have to be sufficiently dimensioned. The
power supply units have to be protected against overcurrent by means of
appropriate input fuses.
efesotomasyon.com - Lenze