Leviton CONTECH LIGHTING LPU2121 User manual

LPU2 120V INST REV0121
CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE [phone] | www.contechlighting.com
© 2020 Conservation Technology of Illinois, LLC. All rights reserved. Note: Specifications subject to change without notice.
Note: Before attempting installation please refer to your local electrical code.
INSTALLATION INSTRUCTIONS | 120V LED Dimmable 3-Color Level
Under Cabinet Light:
LPU2121, LPU2181, LPU2241 & LPU2321
P1
1 x Installation Instructions
All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before attempting to install
this product. It is advisable to keep these instructions in a safe place
for further reference.
WARNING: These products may represent a possible shock or fire
hazard if improperly installed or attached in any way.
Products should be installed in accordance with these
instructions, current electrical codes and/or the current
National Electric Code (NEC).
WARNING: To avoid electrical shock, disconnect or disable power at
the source prior to installation or maintenance.
WARNING:
To avoid electrical shock, and to assure proper operation,
t
his fixture must be adequately grounded.
WARNING: To avoid electrical shock, use only with 120V AC power
input and/or approved cords. Factory warranty will be
void if used with any other power input or cords.
WARNING:
To avoid electrical shock, and to assure proper operation,
this fixture must be adequately grounded.
WARNING: 12-inch minimum spacing distance from luminaire
required for all objects located under fixture.
WARNING: Linkable total wattage is 200 Watts.
SAFETY INSTRUCTIONS
1. The ConTech Lighting LPU2 Undercabinet Light is cETLus listed to
UL and CSA standards and intended for indoor use in dry or damp
locations. Do not use in the vicinity of standing water or liquids.
Do not submerge in water or liquids.
2. Do not use if there is any damage to the unit or to the power
cords’ insulation. Inspect periodically.
3. Do not route cords or units through walls, doors, windows or any
similar part of a building structure.
4. Do not secure unit or its power cord with staples, nails, or any
other sharp objects that may damage the cords.
5. Please read and understand these instructions before beginning
installation.
MAINTENANCE & CARE
1. Ensure that the power is disconnected prior to cleaning.
2. To keep the finish of this product, wipe over with soft cloth
periodically.
3. Do not use harsh chemical solvents, it may dis-colour or damage
the finish.
PREPARATION FOR INSTALLATION
1. Disconnect electrical power before installing or servicing any part
of this fixture.
2. Place fixture on a clean flat surface.
3. Determine input power connection method (Plug-In, Hardwire).
Components
1 x LED 3-Color Level Light 1 x 6 Ft. Power Cord End-to-End Connector 2 x Screws Jumper Connector 3/8"Electrical Connector

LPU2 120V INST REV0121
CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE [phone] | www.contechlighting.com
© 2020 Conservation Technology of Illinois, LLC. All rights reserved. Note: Specifications subject to change without notice.
Note: Before attempting installation please refer to your local electrical code.
INSTALLATION INSTRUCTIONS | 120V LED Dimmable 3-Color Level
Under Cabinet Light:
LPU2121, LPU2181, LPU2241 & LPU2321
Finally, plug-in the power cord to 120VAC power outlet.
Attach the fixture to the cabinet using two (2) included screws. Connect multiple fixtures by plugging in the End-to-End connector or
Jumper connector to input and output sides of fixture. Leave
connector covers installed on unused connections.
By flipping the switch (a), select between one of the three (3) modes:
Lo, Off and Hi.
Switch (b) is used to change the color temperature of light delivered:
2700K, 3000K and 4000K respectively.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA FENTE LA
PLUS LARGE
INSTALLATION PROCEDURES
Plug-In Instructions
FIGURE 1
FIGURE 3 FIGURE 4
FIGURE 2
P2

LPU2 120V INST REV0121
CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE [phone] | www.contechlighting.com
© 2020 Conservation Technology of Illinois, LLC. All rights reserved. Note: Specifications subject to change without notice.
Note: Before attempting installation please refer to your local electrical code.
INSTALLATION INSTRUCTIONS | 120V LED Dimmable 3-Color Level
Under Cabinet Light:
LPU2121, LPU2181, LPU2241 & LPU2321
• Connect the Green Ground Input Supply Wire to the fixture Green
Ground Wire
•
Connect the White AC Neutral Supply Wire to the fixture White Wire
• Connect the Black AC Line Voltage Supply Wire to the fixture
Black Wire
*Do not mix wires or change polarity*
Feed wires back into fixture, re-attach adapter plate, tighten screw
and attach the fixture to the base of cabinet with screws as shown
in Step 1 and 2 of Plug-in Instructions above.
Insert 3/8" electrical connector into the open hole on the adapter.
Secure it with the nut.
Remove the adapter plate by loosening screw.Remove the knock-out with hammer and punch.
Pull three (3) wires out of the fixture to allow connection to AC
supply wires.
Insert wires into the open hole of each push-in wire connector.
INSTALLATION PROCEDURES
Hardwire Instructions
FIGURE 1
FIGURE 3 FIGURE 4
FIGURE 5 FIGURE 6
FIGURE 2
P3