Leviton Opt-X SDX 5WLRG-12C User manual

Instructions for Use - Opt-X®SDX Wallmount Enclosures
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.
Tech Support: 1.800.824.3005 E-mail: [email protected] Web: www.leviton.com
Copyright © 2017 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
MTP®is a registered trademark of US Conec, Ltd.
Page 1 of 13
DI-000-5WLRG-00A
5WLRG-12C
5WLRG-12C

FIBER CONNECTOR SAFETY WARNINGS
SAFETY INFORMATION
• Always wear safety glasses.
• Isopropyl alcohol is ammable and may cause eye irritation. In case of contact with eyes, ush with water for at least
15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion, consult a
physician immediately.
• Never look directly into a laser light source, point source at a person’s eyes, or point source at reective surfaces.
• When working on a ber link, always turn laser source o󰀨, or disconnect completely.
• Always dispose of ber debris properly, preferably using sticky tabs.
• Do not place food or beverages in the vicinity of the work area.
• Thoroughly wash face and hands after terminating ber.
• Carefully remove any ber debris that may have been stuck to clothing, or left in work area, and
dispose of properly.
TIPS AND RECOMMENDATIONS
• Using isopropyl alcohol, thoroughly clean exposed ber and bu󰀨er ensuring both are free from dust, oil,
and debris.
• Do not lay ferrule dust covers on a dirty or dusty surface.
• Always use proper tools and/or accessories to terminate bers and clean connector tips.
QUICK START GUIDE
The following instructions will help you quickly install your Leviton Opt-X®Wallmount Enclosure for use in your equipment
cabinet or rack. For detailed information on each step, go to the page number listed below.
Safety Instructions Pg. 2
Quick Start Guide Pg. 2
Equipment Guide Pg. 3
Standard Accessories Pg. 4
Optional Accessories Pg. 4
Required Hardware and Tools Pg. 4
Congurations Pg. 5
• Adapter Plates
• Splicing
• SDX Cassette
Mounting Pg. 5
Grommet Preparation and Use Pg. 5
Cable Installation Applications Pg. 7
• Adapter Plates
• SDX Cassette
• Splicing
Grounding armored cabling
Installing the optional lock kit Pg. 12
Labeling Pg. 13
Page 2 of 13 DI-000-5WLRG-00A

Page 3 of 13
DI-000-5WLRG-00A
1. Mounting Eyelets
2. Wire management saddle mounting holes
3. Splice tray mounting point
4. Door latch
5. Cable entrance grommet
6. Cable lacing point
7. SDX bulkhead (Removable)
8. SDX bulkhead Mounting point
9. Grounding Stud
10. Service Door
11. Patch Door
12. Optional lock knockout blank
13. Optional Cable Clamp mounting point
EQUIPMENT OVERVIEW - LARGE
Pour les traductions en français, allez à:
Para las traducciones en español, visite:
www.leviton.com

Page 4 of 13
DI-000-5WLRG-00A
STANDARD ACCESSORIES
Description Image Quantity in
Lg Kit
Port Identication
Label 1
Wire Management
Saddles
8 Medium
3 Large
Velcro 5" 8
Grommets 4
#10 Wood Screw 4
Grounding Lug 1
Blank Adapter Plate 8
Lock CAM 1
OPTIONAL ACCESORIES
Lock and Key 5L000-LOK
Universal Clamp Kit (single) 5RCMP-KIT
Universal Clamp Kit (multi) 5RCMP-KT2
SDX to HDX adapter bracket HDXAD-ACC
Splice Trays (See splice tray congurator)
Splice Tray Mounting Hardware Kit SPLMT-HKT
REQUIRED HARDWARE AND TOOLS
Mounting screws/lag bolts, wall anchors, washers as appropriate
Small Magnetic Torpedo level
Powered drill or screw driver
Scissors or safety blade utility knife

Page 5 of 13
DI-000-5WLRG-00A
CONFIGURATIONS
MOUNTING INSTRUCTIONS
1. Determine the location to mount the enclosure. Use the following considerations in selecting a mounting location:
a. Appropriate mounting base per applicable codes and Authority Having Jurisdiction (AHJ)
b. Space around the enclosure to open the door and route patch cables.
c. Adequate space above or below the enclosure to maintain industry standard bend radius compliance of all
cables entering the enclosure.
2. If using the large enclosure in the splice only conguration, install the splice tray hardware before mounting the
enclosure.
3. Using a level, place the enclosure at the target mounting location and mark the four mounting hole positions.
4. Install the top two screws and verify the enclosure is level during nal tightening of screws.
5. Install the bottom two screws.
There are ve possible congurations using the large enclosures.
1. Field or pre-terminated cabling used with SDX adapter plates
2. Pigtail splicing used with SDX adapter plates
3. Pigtail splicing used with Splice modules
4. Use with pre-terminated MTP cabling and SDX cassettes or SDX to HDX adapter brackets
5. Additionally, the large enclosure is convertible to a splice only enclosure
See the Installation section for diagrams of each conguration.
GROMMET PREPARATION AND USE
Cable Grommets are provided and designed for use at both trunk and patch cord entrance points to the enclosure.
There are several options in conguring the grommets. When patching, it is recommended to cut a channel at the front
of the grommet to easily install patch cords. When routing trunks it may be desired to cut a channel at the rear of the
grommet to allow for grommet removal for adding additional trunk cables. Grommet pass through material can either be
slit to limit dust and water egress or removed entirely. To congure a grommet, use the following cutting methods:
1. Determine required opening in cable entrance grommet
2. Determine whether slitting or removing material will be performed
3. Using a sharp-edged tool, cut the appropriate opening in using the scored marking lines as shown in gure 2:
4. Optional – cut a channel through the outer wall of the grommet for either trunk or patch cord routing.
Figure 1
For Large

Page 6 of 13
DI-000-5WLRG-00A
Estimated Fill Ratios
Cable Description
(based on 50% ll)
Diameter in
inches
Diameter in
MM
Qty per Large
Grommet
Micro Data Center 12s Plenum 0.16 4.06 26
Micro Data Center 24s Plenum 0.18 4.57 20
Micro Data Center 48s Plenum 0.231 5.87 12
Micro Data Center 72s Plenum 0.275 6.99 9
Micro Data Center 144s Plenum 0.36 9.14 5
Trunk 12s Distribution/Loose Tube 0.18 4.57 20
Trunk 24s Distribution/Loose Tube 0.38 9.65 5
Trunk 48s Distribution/Loose Tube 0.38 9.65 5
Trunk 72s Distribution/Loose Tube 0.44 11.18 3
Trunk 144s Distribution/Loose Tube 0.69 17.53 1
Trunk 12s Armored - MDP 0.495 12.57 3
Trunk 24s Armored - MDP 0.495 12.57 3
Trunk 48s Armored - MDP 0.584 14.83 2
Trunk 72s Armored - MDP 0.594 15.09 2
Trunk 144s Armored - MDP 0.708 17.98 1
Trunk 12s Armored - All types 0.55 13.97 2
Trunk 24s Armored - All types 0.95 24.13 1
Trunk 48s Armored - All types 1.05 26.67 1
Trunk 72s Armored - All types 1.23 31.24 0
Trunk 144s Armored - All types 1.73 43.94 0
Generic UTP Copper Cat5e 0.185 4.70 19
Generic UTP Copper Cat6 0.23 5.84 12
Generic UTP Copper Cat6A 0.33 8.38 6
Figure 2

Page 7 of 13 DI-000-5WLRG-00A
CABLE INSTALLATION
1. Feed incoming cable(s) through the grommet opening.
2. Optional – Install Universal Trunk Clamp kit and secure cable to clamp.
3. Remove required outer cable jacket leaving jacket at the closest lance point.
4. Secure the cable to the lance point with Velcro or nylon tie wraps as appropriate.
5. If applicable, secure aramid yarn to lance point.
6. When using Armored cable, secure the ground wire from the armored cable to the provided grounding lug or
ground by other code compliant methods to the provided grounding stud.
7. Using the cable management saddles, route the breakout ber legs to the patching or termination point as shown
in the conguration drawings below: (Figures 2 to 8)
ROUTING – LARGE ENCLOSURE
The following set up correctly positions Wire Management Saddles for Field/Pre-terminated cabling, Pigtail Splicing and
use of Fan Out kits to SDX Adapter Plates
Routing of cables for each termination method is as shown in the following gures.

Page 8 of 13
DI-000-5WLRG-00A
ROUTING FOR FIELD AND PRE-TERMINATED TERMINATION
ROUTING FOR FIELD TERMINATED CABLING – PIGTAIL SPLICING
ROUTING FOR FIELD TERMINATED CABLING – FAN OUT

Page 9 of 13 DI-000-5WLRG-00A
SPLICE ONLY CONFIGURATION (LARGE ENCLOSURE ONLY)
The large enclosure (#5WLRG-12C) can be modied to perform splicing only for increased splicing capacity. To convert
the large enclosure, remove the bulkhead from the Enclosure base.
1. Remove the four screws located on the sides and bottom of the enclosure and remove the bulkhead
2. Position FOCA saddles as shown in (Figure 4)
3. Install threaded studs into one or both mounting holes.
NOTE: if fully populating the enclosure an additional Splice Hardware Mounting Kit (SPLMT-HKT) will be required.
4. Install inbound trunks and outbound trunks or assemblies and secure via Optional Cable Clamp kit and/or to tiedown
points at the entrance to the enclosure as necessary.
ROUTING FOR PRE-TERMINATED CABLING – CASSETTES
ROUTING FOR FIELD TERMINATED CABLING – SPLICE MODULES
Figure 2
Figure 3

Page 10 of 13
DI-000-5WLRG-00A
When performing splice terminations, it is recommended to pre-route and mark trunk and pigtail cabling prior to per-
forming any routing, trimming and termination. Splice work can then be performed outside of the enclosure at the
termination equipment. When routing terminated assemblies, route in the primary trunk cabling (dotted line in Figure 5)
rst, followed by the secondary trunk cabling or pigtail assemblies (solid line in Figure 5). To maintain future accessibil-
ity, keep each set of cabling (trunk and pigtail respectively) routed separately through the Wire Management saddles.
Securing Splice trays is achieved with Splice Tray Mounting Hardware Kit (SPLMT-HKT) as identied previously in the
Installation section of this document.
Figure 4
Figure 5
When using Cassettes, congure the Wire Management saddles and route cabling as shown in gure 2:

Page 11 of 13 DI-000-5WLRG-00A
3. Place the Velcro under and around the second lance point
4. Fold the end over the splice tray(s). (Figure 7).
SECURING THE SPLICE TRAYS (LARGE – SPLICE ONLY CONFIGURATION)
Securing the splice trays requires two components:
• Splice Tray Mounting Kit including appropriate #10-32 threaded bolt and wing nut
• Velcro strip (bulk Velcro or Velcro supplied in the Splice Tray Mounting Kit)
1. Prior to mounting the enclosure, install appropriate #10-32 threaded bolt from the rear of the enclosure
base an secure trays with wing nut.
2. Insert Velcro strip under the rst arrow lance point with the hook side facing up (Figure 6).
Figure 6

Page 12 of 13
DI-000-5WLRG-00A
5. Create a snug mating of the Velcro to the trays. (Figure 8).
6. Trim excess Velcro as necessary.
OPTIONAL LOCK KIT
A lock can be installed on the service door, patch door or both doors of each enclosure as required. If
using the optional Lock kit #5L000-LOK
Large
1. Remove the plastic lock blank
2. Remove the CAM from the lock set, set the lock CAM aside
3. Insert the lock set into the Enclosure door
4. Install the lock CAM provided in the Accessory Kit
Figure 7
Figure 8

Page 13 of 13
DI-000-5WLRG.00A
LABELING
A Port Identication Label is provided with each Wall Mount Enclosure. The label should be a󰀩xed to the
inside of the patch bay door. Labeling within the slot position cells can be achieved with printed labels or via
excel based spreadsheets available via download at www.leviton.com.
A󰀩x labels as shown in the following Labeling Conguration matrix
NOTE: Ensure that the label surface area is clean of dirt, oil,
and debris. Recommend use of isopropyl alcohol or a simple
soap and water solution when wiping down surface area.