Leviton CN200 User manual

For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
www.leviton.com
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not
for the benefit of anyone else that this product at the time of
its sale by Leviton is free of defects in materials and
workmanship under normal and proper use for two years from
the purchase date. Leviton’s only obligation is to correct such
defects by repair or replacement, at its option, if within such
two year period the product is returned prepaid, with proof of
purchase date, and a description of the problem to Leviton
Manufacturing Co., Inc., Att: Quality Assurance
Department, 59-25 Little Neck Parkway, Little Neck, New
York 11362-2591. This warranty excludes and there is
disclaimed liability for labor for removal of this product or
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded,
misused, opened, abused, or altered in any manner, or is
not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other
or implied warranties of any kind, including merchantability
andfitnessforaparticularpurpose,butifanyimpliedwarranty
is required by the applicable jurisdiction, the duration of any
such implied warranty, including merchantability and fitness
for a particular purpose, is limited to two years. Leviton is not
liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of
use of, any equipment, lost sales or profits or delay or failure
to perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty,
whether based on contract, tort or otherwise.
DI-000-CN200-00A-Pilot1
C O L L E C T I O N B Y L E V I T O N
Dimming Controller w/IR
Receiver (Multi-Location)
Cat. No. CN200
24VDC
24mA, 0.6W
For use w/Dimming Power Pack and
other Leviton LCnet products
For more information go to
www.leviton.com/centura
INSTALLATION INSTRUCTIONS
DI-000-CN200-00A-Pilot1
Frame
Strap
Snaps
Push in 2 Locations
ON
MAX
BRIGHT
DIM
OFF
IR Receiver
A
A
A
A
Figure 1 - Dimming Controller Functions
Figure 2 - Color Conversion
FEATURES
•Leviton’s Decora®Style design •Separate ON, MAX, BRIGHT, DIM and OFF buttons
•Enables settings of Power Pack •Color conversion available
•Low-Voltage for easy installation •Fits standard wall box
INTRODUCTION
The Dimming Controller w/IR Receiver, Cat No. CN200, allows-easy-to use manual control of a Centura Lighting Control System.The Controller has separate ON, MAX, BRIGHT, DIM and
OFF buttons and the ability to communicate through an IR remote control to provide simple control of your Power Pack. The Controller allows manual control of your lights and programming
of the Power Pack from a standard wall box in an easy-to-reach location. In using the Controller, you may override the automatic operation of the Power Pack to give the most convenience to
your lighting needs.
DESCRIPTION
The Controller has a user-friendly five-button face. The five buttons from top to bottom are ON, MAX, BRIGHT, DIM and OFF (refer to Figure 1). Each button will illuminate when pressed.
The Controller also has a removable face so that the colors can be changed.
The Controller is a component of the Centura Lighting System. It is used to provide local user control of the lights and allows programming of the Power Pack. The Controller provides the
ability to program the Minimum and Light Maintain light levels, and the Power Pack address for multiple Power Pack installations. The programming sequence is described under the “TO
OPERATE”section.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
INSTALLATION INSTRUCTIONS
WARNING: TO BE INSTALLEDAND/OR USED INACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
WARNING: IF YOU ARE NOTSURE ABOUTANY PART OF THESE INSTRUCTIONS, CONSULT AQUALIFIED ELECTRICIAN.
CAUTION: DISCONNECT POWER WHEN SERVICING FIXTURE OR CHANGING LAMPS.
CAUTION: THE DIMMING CONTROLLER WITH IR OPERATES OFF OF LOW-VOLTAGE (24VDC), SO CARE MUST BE TAKEN WHEN REPLACING ALIGHT SWITCH. CONSULT LOCAL
BUILDING CODES AND REGULATIONS FOR PROPER LOW-VOLTAGE INSTALLATION.
TO INSTALL:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
2. Remove existing wallplate and switch or dimmer, if applicable
CAUTION: IF APPLICABLE, ENSURE THAT CIRCUIT CONDUCTORS ARE PROPERLY CAPPED OFF WITH WIRE CONNECTORS AND REMOVED FROM WALL BOX.
3. Connect per appropriate WIRING DIAGRAM as follows: Insert each lead into appropriate Plug connector location by pushing firmly (refer to Wiring Diagram 1). If using stranded wire,
twist strands of each lead tightly (making sure that there are no stray strands) and push firmly into appropriate Plug connector location. Tighten the screws on the Plug connector making
sure that no bare conductor shows. Connect Plug connector to Jack on the back of the Controller.
4. If using a multi-Power Pack setup, using a small screwdriver adjust the address wheels (located on the back of the Controller) to the desired address. Otherwise, there is no adjustment
needed to the address.
5. Carefully position all wires to provide room in outlet box for Controller. Mount Controller into box with mounting screws supplied.
6. Replace wallplate as follows:
•Remove "A" tab when using standard Decora®wallplate (refer to Figure 1).
•Leave “A”tabs intact when using Decora®Screwless wallplate.
7. Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE.
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color conversion kit of the appropriate color from your Leviton distributor and proceed as
follows (please note that wallplate must be removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using a small screwdriver,gently remove the frame from the strap (refer to Figure 2).
3. Take the new frame and position it properly to the strap. Orient the frame so that the ON button is the top button. Line up the plastic snaps with the square holes in the strap. Insert the
snaps on one side of the frame into the strap.
4. Firmly press sideways and down to slip the other snaps into place. The frame snaps in with an audible click. Ensure that all four snaps are secure. Replace Decora®wallplate. The color
conversion is complete.
TO OPERATE
ON: Press the ON button. The lights will fade on to previously set light level.
OFF: Press the OFF button. The lights will fade OFF.
DIM: Press and hold the DIM button to the desired level.
BRIGHTEN: Press and hold the BRIGHT button to the desired light level.
FULL BRIGHT: Press the MAX button at anytime - OR - Press the ON button twice. If the lights are already ON, press the ON button again.
COMMUNICATION LED: The communication LED will flash when the Controller transmits a message, and when it receives a valid message. It is not visible from the face of the device.
DI-000-CN200-00A-Pilot1 9/21/01, 4:33 PM1

GND (Green) GND
Not Used Not Used
+24V DC (Green/White) +24V DC
CAN-L (Blue/White) CAN-L
CAN-H (Blue) CAN-H
To Power Pack
Back of Dimming Controller
Address Switch
Left Address Switch
Right
GND (Green)
GND
Not Used
Not Used
+24V DC (Green/White)
+24V DC
CAN-L (Blue/White)
CAN-L
CAN-H (Blue)
CAN-H
GND (Green) GND
Not Used Not Used
+24V DC (Green/White) +24V DC
CAN-L (Blue/White) CAN-L
CAN-H (Blue) CAN-H
To Power Pack
Back of Dimming Controller Back of Dimming Controller
Wiring Diagram 2 - Two Location Application
Wiring Diagram 1 - Single Station Application
DI-000-CN200-00A-Pilot1
NOTE: Both Controllers must have the same address for multiple location control of 1 Power Pack.
BUTTONS: Each button will illuminate when pressed except when the Controller is in the Program Mode. Under normal use the buttons will act as follows:
•Only the ON button will remain illuminated whenever the load is on.
•The MAX and ON buttons will both remain illuminated whenever the load is ON maximum output.
•The BRIGHT and DIM buttons will turn ON when they are pressed and held, and then turn off when released.
•The OFF button will remain illuminated whenever the load is OFF.
LIGHT LEVELS:
MIN: The minimum light level is adjustable between 0%-40%.
Light Maintain: The Light Maintain level is the amount of light that the Power Pack will maintain in the room. The Power Pack maintains a programmed light
level by adjusting the lights to compensate for the ambient light present in the room. If the room is very bright (mid-day), the lights will be set to a DIM level. If
the room is dark (evening and morning), the lights will be set to a BRIGHT level. This desired level of light is programmed by the Controller.
POWER PACK ADDRESS:
The Controller and the Power Pack must have the same address in order to communicate to each other. The default address is the same, but when installing
multiple Power Packs with individual Controller, each Power Pack must have a different address.
The Controller has 2 rotary switches (located on the back of the device) for addressing. When setting address 0 through 16 (0-F), use rotary switch located on
lower left hand side of device (refer to Wiring Diagram 1). If there is only one Power Pack on the bus then the switch DOES NOT have to be adjusted. For
installations where there are multiple Power Packs, the rotary switch is used to set the Power Pack’s address (refer to the Power Pack Instruction Sheet for
further details).
NOTE: Rotary switch on lower right hand side of device will be used for additional address configurations, where applicable.
To set the Power Pack’s address, proceed as follows:
1. Place the Controller into Program Mode by pressing and holding the MAX button for 7 sec.
2. Press theAddress Selection button on the Power Pack.
3. Let the Controller “Time-out”of Program Mode or press the MAX button to exit Program Mode.
4. The Address is now selected.
NOTE:
•Only one Power Pack can be programmed at a time.
•Address wheels should be set to desired address before installing the Controller.
MULTI-LOCATION:
All Controllers MUST be on the same address.
PROGRAMMING
1. Press and hold the MAX button for 7 seconds. All the buttons will blink to indicate that the Controller is in Program Mode.
2. To program the Light Maintain Level, press the ON button while in program mode. The ON button will now be the only button blinking to indicate that you
are setting the Light Maintain Level. Press the BRIGHT and DIM buttons to adjust lights to desired level maintained by the photocell. Press the MAX button
to exit Program Mode.
3. To program the Minimum Light Level, press the OFF button while in program mode. The OFF button will now be the only button blinking to indicate that
you are setting the Minimum Light Level. Press the BRIGHT and DIM buttons to adjust lights to the desired minimum level. Press the MAX button to exit
Program Mode.
4. Press MAX button again to exit programming mode at any time or allow the Controller to “Time-out”by not touching any buttons for 2 minutes.
NOTES:
•To return to any previous programming step, press the button associated with the level you desire to set.
•If there is no activity for 2 minutes during any of the steps, the Controller will “Time-out”or exit the program mode.
Handheld Infrared Remote Control PROGRAMMING:
MAX: Press the MAX button on the Remote control. The MAX button on the Dimming Controller w/IR receiver will start to flash. Using the DIM and BRIGHT
buttons on the Remote Control adjust the lights to desired level. Press the MAX button on the Remote Control again. The MAX button on the Controller will
stop flashing. Now the maximum level of the load has been set.
MIN: Press the MIN button on the Remote control. The OFF button on the Controller will start to flash. Using the DIM and BRIGHT buttons on the Remote Control
adjust the lights to desired level. Press the MIN button on the Remote Control again. The OFF button on the Controller will stop flashing. Now the minimum
level of the load has been set.
LIGHT MAINTAIN: Press the DAYLIGHT button on the Remote control. The ON button on the Controller will start to flash. Using the DIM and BRIGHT buttons
on the Remote Control, adjust the lights to desired level. Press the DAYLIGHT button on the Remote Control again. The ON button on the
Controller will stop flashing. Now the DAYLIGHT light level of the load has been set.
PRESETS 1, 2, 3, 4: Press the PRESET button on the Remote Control. The BRIGHT button on the Controller will start to flash. Now press one of the four
numbered (1, 2, 3, 4) preset buttons on the Remote Control. Using the DIM and BRIGHT buttons on the Remote Control adjust the lights to
desired level. Press the same numbered preset button on the Remote Control again. The BRIGHT button on the Dimming Controller will stop
flashing. Now that number’s preset light level has been set.
NOTE: Any level can be programmed or reprogrammed at any time.
TROUBLESHOOTING
•If NO LED’s are lit; there is no power
- Check wiring.
•Communication LED does NOT light when the button is pressed
- Check power wiring connections.
For Multiple Power Packs on the Bus:
•The Controller has power (at least the OFF LED is ON) but pressing the buttons have no effect on the lights; there is no communication between the
Controller and the Power Pack
- If the communication LED does NOT flash when a button is pressed, see above.
- If the communication LED does flash, check the address of the Power Pack and Controller (refer to Dimming Power Pack Instructions).
NE200 Remote
NE200 Remote
DI-000-CN200-00A-Pilot1 9/21/01, 4:33 PM2