LG ATC5CPC001 User manual

0 / 10
Copyrightⓒ. 2019. All Rights Reserved.
Description
- Model : ATC5CPC001
- WLAN: 802.11 a/b/g/n/ac
- Frequency Range : 2400MHz ~ 5845MHz
Features
- Dimension : 22.5mm x 20.0mm x 2.9mm
- TemperatureRange : -40℃~ +85℃
- Supply Voltage : VBAT 3.2V to 3.6V
- Output Power
WLAN: 17.0dBm(11b11Mbps), 16dBm(11g 54Mbps, 11n 2.4G MCS7),
15dBm(11a54Mbps), 14dBm(11n 5G MCS7), 11dBm(11ac MCS9)
- Interface: PCIe(WLAN)
Application
- Automotive (OutdoorDevice)
Dimensions
ATC5CPC001 User Manual

1 / 10
Copyrightⓒ. 2019. All Rights Reserved.
1) Recommended operation conditions
2)Current consumption
Parameter Min. Typ. Max. Unit
Operating Temperature Range -40 - +85 ℃
Supply Voltage : VBATT (3.3V)1) 3.2 3.3 3.6 V
Supply Voltage : VIO 1.62 1.8 1.98 V
2.97 3.3 3.63 V
Parameter Average Max. Unit
Stand-by (BT & WLAN) 5 10 mA
WLAN Continuous Rx2) 280 360 V
WLAN Continuous Tx2) 790 1,000 V
Bluetooth Connection 35 40 V
Leakage current 15 uA
Operating condition
ATC5CPC001 User Manual

2 / 10
Copyrightⓒ. 2019. All Rights Reserved.
VBAT
WL_REG_ON
VDDC
(on-chip PMU)
PCIE_CLKREQ_L
PCIE_REFCLK
Max. 12.4msec
21.2msec
VIO
> 0ms
100us
PCIE_PERST_L
6msec PCIE_PERST_L D assertion to first config access
Boot up sequence
ATC5CPC001 User Manual

3 / 10
Copyrightⓒ. 2019. All Rights Reserved.
• Operation Voltage is 3.3V/1.8V Dual Power Rail
• Up to 866 Mbps data rate
• Support 2 Antenna port
: BT and WLAN ANT1, WLAN ANT2
• Integrated External RF Switch and Internal PA/LNA at 2.4GHz,
Internal PA and External RF Switch and LNA at 5GHz
• RoHS Compliant
• Size : 22.5 x 20.0 x 2.9 mm3
• Support bandwidth : HT20 / HT40 / VHT80
• Interface : PCIe(WLAN), UART(BT),PCM/I2S
• Package type : SMD type(Side-via)
ATC5CPC001 User Manual
General Features

4 / 10
Copyrightⓒ. 2019. All Rights Reserved.
BT(v5.0) + 2.4GHz/5GHz WiFi 5 (802.11a/b/g/n/ac) 2x2 MIMO Module
1) BluetoothKey Features
• Supports key features of upcoming Bluetooth standards
• Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate)
EDR features:
-. Adaptive Frequency Hopping (AFH)
-. Quality of Service (QoS)
-. Extended Synchronous Connections (eSCO) –Voice Connections
-. Fast Connect (interlaced page and inquiry scans)
-. Secure simple Pairing (SSP)
-. Sniff Sub rating (SSR)
-. Encryption Pause Resume (EPR)
-. Extended Inquiry Response (EIR)
-. Link Supervision Timeout (LST)
• UART baud rates up to 4 Mbps
• Supports all Bluetooth 4.2 packet types
• Supports maximum Bluetooth data rates over HCI UART
• Multipoint operation with up to seven active slaves
-. Maximum of seven simultaneous active ACL links
-. Maximum of three simultaneous active SCO and eSCO connections with
scatternet support
• Narrowband and wideband packet loss concealment
• Scatternetoperation with up to four active piconets with backgroundscan and
support for scatter mode
• High-speed HCI UART transport support with low-power out-of-bandBT_DEV
WAKE and BT_HOST_WAKEsignaling
• Channel quality driven data rate and packet type selection
• Standard Bluetooth test modes
• Extended radio and production test mode features
• Full support for power savings modes
-. Bluetooth clock request
-. Bluetooth standard sniff
-. Deep-sleep modes and softwareregulator shutdown
Bluetooth(BT5.0 compliant)
General Features
ATC5CPC001 User Manual

5 / 10
Copyrightⓒ. 2019. All Rights Reserved.
1) WLAN RF band & modulation Features
• Dual-band 2.4GHz and 5GHz WiFi 5 (802.11a/b/g/n/ac)
• Dual-stream up to 866Mbps data rate
• Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation)
• Tx and Rx low-density parity check(LDPC)
• Supports IEEE 802.11ac/n beamforming
• Supports two antennas with one dedicated to Bluetooth and WLAN and one to WLAN.
• PCIe mode complies with PCI Express base specification revision 3.0 for x1 lane
and power managementrunning at Gen1 speeds
• WPA and WPA2(Personal) support for powerful encryption and authentication
• AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility
• Reference WLAN subsystem provides Wi-Fi protected Setup(WPS)
2) WLANMAC features
• Enhanced MAC for supporting IEEE 802.11ac features
• Transmission and reception of aggregated MPDUs(A-MPDU) for high throughput(HT)
• Support for power management schemes, including WMM power-save multi-poll(PSMP)
and multiphase PSMP operation
• Support for immediate ACK and block-ACK policies
• Inter-frame space timing support, including RIFS
• Back-offcounters in hardware for supporting multiple priorities as specified in the WMM
specification
• Timing synchronization function(TSF), network allocation vector(NAV) maintenance, and
target beacon transmission time(TBTT) generation in hardware
• Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEPciphers, WAPI,and
support for key management
• Programmable independent basic service set(IBSS) or infrastructure basic service set
functionality
WLAN
ATC5CPC001 User Manual
General Features

6 / 10
Copyrightⓒ. 2019. All Rights Reserved.
3) WLAN PHY features
• Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels,
as specified in IEEE 802.11ac
• Improved performance with 2x2 channel smoothing and spur canceller support
• Supports Optional short GI and Green field modes in Tx and Rx
• Tx and Rx LDPC for improved range and power efficiency
• Beamforming support
• Supports IEEE 802.11h/k for worldwide operation
• Advanced algorithms for low power, enhanced sensitivity, range, and reliability
• IEEE 802.11a, 11b, 11g, 11n, 11ac single stream PHY standards
• Designed to meet FCC and other worldwide regulatory requirements
ATC5CPC001 User Manual
General Features
WLAN

7 / 10
Copyrightⓒ. 2019. All Rights Reserved.
<TOP View>
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22
45
46
47
48
31
30
29
28
27
26
25
24
23
44 43 42 41 40 39 38 37 36 35 34 33 32
ATC5CPC001 User Manual
Pin Configuration

8 / 10
Copyrightⓒ. 2019. All Rights Reserved.
No. Pin Name I/O Description
1 PCIE_CLK_P I PCIE differential clock input positive
2 PCIE_CLK_N I PCIE differential clock input negative
3 PCIE_TD_N O PCIE Transmitter differential negative
4 PCIE_TD_P O PCIE Transmitter differential positive
5 N.C. - Not Connected (Reserved)
6 N.C. - Not Connected (Reserved)
7 N.C. - Not Connected (Reserved)
8 N.C. - Not Connected (Reserved)
9 N.C. - Not Connected(Reserved)
10 N.C. - Not Connected (Reserved)
11 BT_DEV_WAKE I Bluetooth device wake from host
12 BT_HOST_WAKE O Bluetooth host wake from device
13 VBAT IPositive supply
- Supply voltage : Typical 3.3V.
14 VBAT IPositive supply
- Supply voltage : Typical 3.3V.
15 GND - Ground
16 N.C. - Not Connected (Reserved)
17 WL_REG_ON I WLAN Power on reset(Power rail : VDDIO)
- Internal 200KΩpull-down
18 BT_REG_ON I BluetoothPower on reset(Power rail : VDDIO)
- Internal 200KΩpull-down
ATC5CPC001 User Manual
Pin Configuration

9 / 10
Copyrightⓒ. 2019. All Rights Reserved.
No. Pin Name I/O Description
19 BT_PCM_CLK I/O PCM clock, can be master (output) or slave (input)
20 BT_PCM_SYNC I/O PCM sync signal, can be master (output) or slave
(input)
21 BT_PCM_IN I/O PCM data input
22 BT_PCM_OUT I/O PCM data output
23 WL_ANT 1 RF BT/WLAN RF ANT 1
24 GND - Ground
25 LPO I Low power clock input(32.768KHz,0V ~ 1.8V peak to
peak)
26 GND - Ground
27 WL_DEV_WAKE I WLAN device wake from host
28 WL_HOST_WAKE O WLAN host wake from device
29 GND - Ground
30 GND - Ground
31 WL_ANT 2 RF WLANRF ANT 2
32 SDIO_PAD I SDIO_PADVDDIO
:If VIO_SD=1.8Vhigh,If VIO_SD=3.3Vlow
33 BT_UART_RTS_N I/O Bluetooth UART request to send
34 BT_UART_CTS_N I/O BluetoothUART clear to send
35 BT_UART_RXD I/O BluetoothUART signal input
36 BT_UART_TXD I/O BluetoothUART signal output
ATC5CPC001 User Manual
Pin Configuration

10 / 10
Copyrightⓒ. 2019. All Rights Reserved.
No. Pin Name I/O Description
37 VIO I BT, WLAN VDDIO supply voltage.(3.3V or 1.8V)
- BT and WLAN should be same power rail
38 SDIO_DIS I SDIO_DIABLE
: Low : SDIO Enabled, High : SDIO Disabled
39 PCIE_EN I PCIE_ENABLE
: Low : PCIE Disabled, High : PCIE Enabled
40 PCIE_PME_L O PCIE power management event output
41 PCIE_PERST_N I PCIE system reset.
42 PCIE_CLKREQ O PCIE clock request signal
43 PCIE_RD_P I PCIE Receiver differential positive
44 PCIE_RD_N I PCIE Receiver differential negative
45 GND - Ground
46 GND - Ground
47 GND - Ground
48 GND - Ground
ATC5CPC001 User Manual
Pin Configuration

FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions:
The module must be installed in the host equipment such that 20 cm is maintained between the antenna and
users, and the transmitter module may not be co-located with any other transmitter or antenna. The module
shall be only used with the internal on-board antenna that has been originally tested and certified with this
module. External antennas are not supported. As long as these 3 conditions above are met, further transmitter
test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.). The end-product may need Verification testing, Declaration of Conformity testing, a
Permissive Class II Change or new Certification. Please involve a FCC certification specialist in order to determine
what will be exactly applicable for the end-product.
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with
another transmitter), then the FCC authorization for this module in combination with the host equipment is no
longer considered valid and the FCC ID of the module cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization. In such cases, please involve a FCC certification
specialist in order to determine if a Permissive Class II Change or new Certification is required.
Upgrade Firmware:
The software provided for firmware upgrade will not be capable to affect any RF parameters as certified for the
FCC for this module, in order to prevent compliance issues.
End product labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users. The final end product must be labeled in a visible area
with the following: “Contains FCC ID: YZP-ATC5CPC001”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user's manual of the end product which integrates this module. The end user
manual shall include all required regulatory information/warning as show in this manual.

FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
“CAUTION : Exposure to Radio Frequency Radiation.
Antenna shall be mounted in such a manner to minimize the potential for human contact during normal
operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC
radio frequency exposure limit.

IC Information
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux
conditions suivantes:
(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l'appareil.
The end product must belabeled todisplay the Industry Canada certification number of the module.
Contains transmitter module IC: 7414C-ATC5CPC001
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.
Contient module émetteur IC: 7414C-ATC5CPC001
*This device is going to be operated in 5 150 MHz ~ 5 250 MHz frequency range, it is restricted in
indoor environment only.
Information for OEM Integrator
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
End product labelling
The label for end product must include
“Contains FCC ID: YZP-ATC5CPC001,Contains IC: 7414C-ATC5CPC001”.
“CAUTION: Exposure to Radio Frequency Radiation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20cm between the radiator and your
body. This transmitter module is authorized only for use in device where the antenna may be installed such that
20 cm may be maintained between the antenna and users.”

Requirement per KDB996369 D03
2.2 List of applicable FCC rules
List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish
the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list
compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant
that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host
manufacturers that further testing is required.3
Explanation: This module meets the requirements of FCC part 15C(15.247). part 15E(15.407)
2.3 Summarize the specific operational use conditions
Describe use conditions that are applicable to the modular transmitter, including for example any limits on
antennas, etc. For example, if point-to-point antennas are used that require reduction in power or
compensation for cable loss, then this information must be in the instructions. If the use condition limitations
extend to professional users, then instructions must state that this information also extends to the host
manufacturer’s instruction manual. In addition, certain information may also be needed, such as peak gain
per frequency band and minimum gain, specifically for master devices in
5 GHz DFS bands.
Explanation: The EUT has a Chip Antenna, and the antenna use a permanently attached antenna which is not replaceable.
2.4 Limited module procedures
If a modular transmitter is approved as a “limited module,”then the module manufacturer is responsible for
approving the host environment that the limited module is used with. The manufacturer of a limited module
must describe, both in the filing and in the installation instructions, the alternative means that the limited
module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module
limiting conditions.
A limited module manufacturer has the flexibility to define its alternative method to address the conditions that
limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation. The alternative method could include that the limited module manufacturer reviews
detailed test data or host designs prior to giving the host manufacturer approval.
This limited module procedure is also applicable for RF exposure evaluation when it is necessary to
demonstrate compliance in a specific host. The module manufacturer must state how control of the product
into which the modular transmitter will be installed will be maintained such that full compliance of the product
is always ensured. For additional hosts other than the specific host originally granted with a limited module, a
Class II permissive change is required on the module grant to register the additional host as a specific host also
approved with the module.
Explanation: The module is not a limited module.

2.5 Trace antenna designs
For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication
996369 D02 FAQ –Modules for Micro-Strip Antennas and traces. The integration information shall include for
the TCB review the integration instructions for the following aspects:
layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements.
a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s),
dielectric constant, and impedance as applicable for each type of antenna);
b) Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency,
the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered);
c) The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC)
board layout;
d) Appropriate parts by manufacturer and specifications;
e) Test procedures for design verification; and
f) Production test procedures for ensuring compliance.
The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna
trace, as described by the instructions, require that the host product manufacturer must notify the module
grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application
is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in
FCC ID (new application) procedure followed by a Class II permissive change application.
Explanation: Yes, The module with trace antenna designs, and This manual has been shown the layout
of trace design, antenna, connectors, and isolation requirements.
2.6 RF exposure considerations
It is essential for module grantees toclearly and explicitly state the RF exposure conditions that permit a host
product manufacturer to use the module. Two types of instructions are required for RFexposure information:
(1) to the host product manufacturer, todefine the application conditions (mobile, portable –xx cmfrom a
person’sbody); and (2) additional text needed for the host product manufacturer toprovide toend users in
their end-product manuals. IfRFexposure statements and use conditions are not provided, then the host
product manufacturer is required totake responsibility of the module through a change in FCC ID(new
application).
Explanation: This module complies with FCC RFradiation exposure limits set forth for an uncontrolled
environment, This equipment should beinstalled and operated with a minimum distance of20 centimeters
between the radiator and your body." This module isdesigned tocomply with the FCC
statement, FCC IDis:YZP-ATC5CPC001.

2.7 Antennas
Alistof antennas included in the application for certification must beprovided in the instructions. For modular
transmitters approved as limited modules, all applicable professional installer instructions must beincluded as
part of the information tothe host product manufacturer. The antenna list shall also identify the antenna types
(monopole, PIFA, dipole, etc. (note that for example an“omni-directional antenna”is not considered tobea
specific “antenna type”)).
For situations where the host product manufacturer isresponsible for an external connector, for example with
an RFpin andantenna trace design, the integration instructions shall inform the installer that unique antenna
connector must beused on the Part 15authorized transmitters used inthe host product. The module
manufacturers shall provide a list ofacceptable unique connectors.
Explanation: The EUT has a PCB Antenna, and the antenna use a permanently attached antenna
which isunique.
2.8 Label and compliance information
Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising
host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID”with
their finished product. See Guidelines for Labeling and User Information for RF Devices –KDB Publication
784748.
Explanation:The host system using this module, should have label in a visible area indicated
the following texts: “Contains FCC ID: YZP-ATC5CPC001,Contains IC: 7414C-ATC5CPC001”
2.9 Information on test modes and additional testing requirements5
Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide.
Test modes should take into consideration different operational conditions for a stand-alone modular
transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host
product.
The grantee should provide information on how to configure test modes for host product evaluation for
different operational conditions for a stand-alone modular transmitter in a host, versus with multiple,
simultaneously transmitting modules or other transmitters in a host.
Grantees can increase the utility of their modular transmitters by providing special means, modes, or
instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a
host manufacturer’s determination that a module as installed in a host complies with FCC requirements.
Explanation: Top band can increase the utility of our modular transmitters by providing instructions
that simulates or characterizes a connection by enabling a transmitter.

2.10 Additional testing, Part 15 Subpart B disclaimer
The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule
parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of
certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains
unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product
still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Explanation: The module without unintentional-radiator digital circuity, so the module does not
require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.