LG LKD1000 User manual

Please read this manual carefully before operating
your set and retain it for future reference.
OWNER’S MANUAL
Dynamic Controller
MODEL
LKD1000
P/NO : MFL62723777

2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulat-
ed dangerous voltage within the product’s
enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the litera-
ture accompanying the product.
FCC WARNING: This equipment may generate or
use radio frequency energy. Changes or modifica-
tions to this equipment may cause harmful inter-
ference unless the modifications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
• A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this prod-
uct in the end user.
• Caution: Danger of explosion if battery is incor-
rectly replaced. Replaced only with the same or
equivalent type recommended by the manufac-
turer. Dispose of used batteries according to the
manufacturer’s instructions.
• Holes in metal, through which insulated wires
pass, shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance
with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interfer-
ence in which case the user may be required to take
adequate measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a quali-
fied service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.

3
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol
is attached to a product it means the prod-
uct is covered by the European Directive
2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the gov-
ernment or the local authorities.
3. The correct disposal of your old appliance
will help prevent potential negative conse-
quences for the environment and human
health.
4. For more detailed information about dis-
posal of your old appliance, please contact
your city office, waste disposal service or
the shop where you purchased the prod-
uct.
LG Electronics hereby declares that
this/these product(s) is/are in compli-
ance with the essential requirements
and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327
AE Almere, The Netherlands
(Tel : [phone])
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recep-
tacles, and the point where they exit from the appa-
ratus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with appara-
tus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power- supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

4
CONTENTS
INTRODUCTION.................................. 5
About LKD1000 Controller.................................5
Features...............................................................5
Identification of the Controller .........................6
HOOKUP AND SETTINGS.................. 8
Basic Connection Overview ..............................8
RS-485 Connection.............................................9
Connecting the LG DVR.....................................9
Connecting the PTZ Camera ...........................10
Connecting the multiple LKD1000 controller 10
System Operation.............................................11
LKD1000 SETUP MENU....................................11
Key Functions on the Setup menu ...............11
Change Password.........................................12
About DVR ....................................................12
About Camera...............................................13
Change ID Setting.........................................13
Auto Lock Setting .........................................13
Factory Reset................................................14
About LKD1000.............................................14
OPERATION ...................................... 14
Operation the LG DVR......................................14
Operation the connected camera via the
DVR...............................................................16
Operation of the camera connected to
the LKD1000 controller directly.................16
Camera Control Menu ......................................17
Camera Control menu overview ...................17
Preset Settings..............................................17
Auto Pan Setup and Activation .....................23
Pattern Setup and Activation ........................24
Privacy Setup................................................25
Communication Settings ...............................26
Camera setup ...............................................29
REFERENCE .................................... 32
Camera Control Function ................................32
Pan/Tilt Control .............................................32
Lens Control..................................................32
Protocol Function Table ..................................33
Specifications ...................................................34

5
INTRODUCTION
About LKD1000 Controller
This controller is the brand of Camera and DVR Controlling Keyboard of LG in a surveillance system. You can
operate this system very easily and conveniently because of design structure based on biotechnology and
various functions for users. In addition, the controller can control using the functions of the LG Camera and LG
DVR system.
The description functions used in this manual are based on LG Multix protocol.
The description functions may differ from your protocol.
Features
The Dynamic Controller offers the following functions:
xUser-friendly Graphical User Interface.
xCompatible with LG Dome Cameras, Zoom Cameras and LG DVRs.
xJoystick Control for PTZ Functions.
xProgram Preset Position and Pattern Control (Memorize continuous series of Zoom In/Out, Pan/Tilt).
xControl Privacy Zone Masking of the camera.
xEasy Firmware Upgrade
(Please contact authorized service center or where you purchased to upgrade the firmware.)
xErgonomic Design.
xDirectly Control the camera connected to LG DVR by using BY-PASS function of LKD1000 controller.
xConnect maximum 16 controller by using cascade (Master 1, Slave 15)
xSupport the use of multiple controllers by cascading.
Note:
The Dynamic Controller is not provided with functions to control the audio signal. Audio communication is not
possible, regardless of whether audio boards are installed in the receiver.

6
Identification of the Controller
 mn o p
 a b c def g
 h i j k l
1LG DVR Control Buttons
For details, see page 15.
2Display Window
Displays function menus, numeric input, and
system status.
3Numeric (0 to 9) and Arrow (left/right/up/down)
Buttons
Selects an option in the menu.
These buttons are used for numeric input of pre-
set numbers or for executing each parameter on
the Controller’s menu.
4Setup Button
Opens controller’s main Setup menu in the dis-
play window.
5Cam OSD Button
Opens or closes the Camera’s Setup menu on
the screen.
6In/Out Buttons
These buttons are used to zoom the camera
image In (TELE) and Out (WIDE).

7Joystick Controller
This joystick manually operates the Pan/Tilt Head
and turning the joystick head to the left or right
will zoom or widen the image. (The zooming level
will go up or down.)
8PTZ Camera Control Buttons
• PRESET Button
For details, see pages 17 to 23.
• A-PAN (Auto-Pan) Button
For details, see pages 23 to 24.
• PTRN (Pattern) Button
For details, see pages 24 to 25.
• ALARM Button
For details, see pages 22 to 23.
• FUNC Button
- In the LKD1000 setup menu:
> FUNC + Number 0: You can adjust the
brightness of the display window (4:
Decrease, 6: Increase).
- In the camera setup menu:
> FUNC + Number 1: If you use LG
Multix Protocol, you can set the parking
time to use the Auto Return function.
If you stop the preset tour, the preset
tour will automatically restarted after
the selected park time passes.
> FUNC + Number 6: If you use LG
Multix Protocol, press the button to
select the Focus mode (Auto, Manual
or PushAuto).
> FUNC + Number 9: If you use LG
Multix, LG Multix E or LG Zoom
Protocol, press the button to activate
auto focus. For using this function,
the camera's focus mode is set to one
push auto focus mode.
- FUNC + Number 2,3,5,7,8: These buttons
are not assigned.
9CLR (CLEAR) Button
This button is used to return to the previous
menu or mode. Clears the parameter entered by
numeric buttons.
0ENTER Button
This button is used to execute the currently
highlighted setting in the Setup menu.
qa Open/Close Buttons
The lens Iris is adjusted by pressing the Open or
Close button.
qs Near/Far Buttons
These buttons are used to adjust the lens focus
of cameras equipped with the specified lens.
qd RS-485 Data Ports (CH 2)
This port is used to connect the other LKD
1000 controller. If you want to use the multiple
LKD1000 controller, connect the RS-485 1CH of
the other LKD1000 controller to this port using the
RS-485 cable.
qf RS-485 Data Ports (CH 1)
This port is used to exchange control data
through the connected camera and/or DVR via
the RS-485 cable or by connecting the master (or
the other) controller.
qg RS-232C Port
This port is used only for authorized service pur-
poses.
qh DC 12 V Input Jack (12 V DC)
Connect a DC 12 V Certified/Listed, class 2
power supply only to the DC input terminal on the
back of the controller.
7

8
HOOKUP AND SETTINGS
Precautions
• The connections should be made by qualified service personnel or system installers in accordance with all
local codes.
• DC 12 V can be used.
Basic Connection Overview
Notes:
• Please refer to the LG DVR and Camera manuals as necessary for additional connection information.
• Set the DVR ID and Camera ID differently for each DVR and Camera if many DVRs or cameras are con-
nected to the LKD1000 controller.
DC 12 V adaptor
(Not supplied).
LKD1000
Controller 1
(MASTER)
LKD1000
Controller 2
(SLAVER)
LKD1000
Controller 3
(SLAVER)
DVR 1 DVR 2 DVR 3
LKD1000
Controller 4
(SLAVER)
Camera 1
Camera 2
Up to 16 controllers.
Up to 256 cameras.
Up to
16 DVRs.
To RS-485 2 CH
terminal.
To RS-485 1 CH
terminal.
RJ11 Cable
(Supplied)

9
RS-485 Connection
Use this port to connect PTZ cameras or LG DVRs. Use the cable that is described below for RS-485 site
communication.
• Shielded, twisted pair cable
• Low impedance
• Wire gauge size is thicker than AWG #22 (0.33 mm2).
Connecting the LG DVR
You can connect up to 16 LG DVRs.
Connect the LG DVR to the RS-485 1 CH terminal of the LKD1000 as shown below.
Notes:
• When connecting lines, connect the TX - of the LKD1000 controller to RX - (DATA2) of the LG DVR and TX
+ of the LKD1000 controller to RX + (DATA2) of the LG DVR correctly.
• Set the appropriate DVR system ID to operate via the LKD1000 Controller when using the multiple LG
DVR.
DC 12 V adaptor
(Not supplied).
LKD1000
Controller 1
(MASTER)
LKD1000
Controller 2
(SLAVER)
LKD1000
Controller 3
(SLAVER)
DVR 1 DVR 2 DVR 3
LKD1000
Controller 4
(SLAVER)
Camera 1
Camera 2
Up to 16 controllers.
Up to 256 cameras.
Up to
16 DVRs.
To RS-485 2 CH
terminal.
To RS-485 1 CH
terminal.
RJ11 Cable
(Supplied)

10
Connecting the PTZ Camera
You can connect up to 256 PTZ cameras. Connect the PTZ Camera to the RS-485 1 CH terminal of the
LKD1000 as shown below.
Connecting the multiple LKD1000 controller
You can connect up to 16 LKD1000 controllers. If you use the multiple LKD1000 controller, you must set the
LKD1000 ID. Set to 1 for master controller and set to the other ID number (2 to 16) for the slave controller.
The Slave LKD1000 controller can control the DVRs or cameras through the master LKD1000 controller. When
connecting multiple LKD1000 controllers, connect as shown below.
To RS485 1 CH
To RS485 2 CH
Master LKD1000 Controller
First Slaver LKD1000 Controller
Second Slaver LKD1000 Controller
To LG DVRs or Cameras.
To RS485 1 CH
To RS485 2 CH
To RS485 1 CH
To RS485 2 CH
Note:
When you turning off the slave LKD1000 controller, you should disconnect the RS485 cable
between the master LKD1000 controller and slaver LKD1000 controller to prevent a malfunction of
the master LKD1000 controller.

11
System Operation
Before starting operation, user authentication by the
password is required.
1. Check that the LG DVR or the camera, the moni-
tor and peripherals are connected correctly and
securely.
2.
Connect an DC 12 V power source to the DC 12 V
input terminal on the back of the controller.
3. Select a user by using the arrow (
B
/
b
) buttons,
then press the ENTER button.
Administrator: Unlimited operation of the unit.
Only administrator can access the LKD1000
setup menu and camera control menu.
Operator: Limited operation of the unit.
(Emulate the DVR keys and PTZ function are
available.)
4. Enter your password using the number buttons
then press ENTER. (Initial password is “000000”.)
The main menu will appear in the display window.
•
•
LKD1000 SETUP MENU
The setup menu has several submenus. All of these
main menus are further divided into submenus.
Press Setup to display the setup menu.
Key Functions on the Setup menu
• Setup button: To display the main menu.
• ENTER button: To execute or select modes and
parameters. To enter a submenu for the selected
item.
• CLR button: To return to the previous menu or to
delete input.
• Numeric buttons: Enter numbered value in a
menu.
• Arrow buttons: Choose an item in the menu.
Camera OSD button
ENTER button
Number and Arrow buttons
CLR button
LKD1000 Setup button

12
Change Password
The factory default of password is “000000”.
However, for security, you should change the pass-
word setting.
1. Select [Change Password] option then press
ENTER. The sub menu will appear.
2. Select the user to change the password and press
ENTER.
3. Enter current password using the number but-
tons then press ENTER. If you select [Change
Operator Password] option, enter the administra-
tor's password.
In case of Administrator:•
In case of Operator:
4. Enter new password using the number buttons
then press ENTER. Enter the password again
to confirm, and press ENTER. The password is
stored.
Notes:
• You can enter the password from minimum 1-digit
number to 10-digit numbers.
• We recommend that you do not operate the con-
troller during saving the password.
About DVR
Select [ABOUT DVR] option then press ENTER.
Shows DVR information.
•

13
About Camera
Select [ABOUT CAMERA] option then press ENTER.
Shows camera information.
Change ID Setting
This LKD1000 controller has the controller ID. If you
use 2 controllers or more simultaneously, set the
controller ID for each controller.
1. Select [CHANGE ID] option then press ENTER.
The sub menu will appear.
CHANGE ID LKD1000
2. Enter the New LKD1000 ID for this controller
(1 to 16).
3. Press ENTER to save the settings.
Auto Lock Setting
The keys on the controller is locked when there is no
operation for selected duration on the [AUTO LOCK]
option. To release the Key Lock mode, you need to
enter the password.
• NONE: Auto Key Lock function is disable.
• After 1 min: The keys on the controller are locked
when there is no operation for 1 minute.
• After 3 min: The keys on the controller are locked
when there is no operation for 3 minutes.
• After 5 min: The keys on the controller are locked
when there is no operation for 5 minutes.

14
Factory Reset
If you need to, you can reset the LKD1000 controller
to its original factory settings.
1. Select [FACTORY RESET] option then press
ENTER.
The sub menu will appear.
2. Enter the password and press ENTER.
3. Press ENTER to confirm it.
About LKD1000
Select [ABOUT LKD1000] option then press ENTER.
Shows model name and the current firmware version
of the controller.
OPERATION
Operation the LG DVR
You can control the connected LG DVR using the
LKD1000 controller.
1. Select DVR icon in the main menu and then
press ENTER. The DVR ID input menu will be
displayed.
2. Enter the connected DVR ID to control the DVR
and then press ENTER. The DVR key emulation
menu will be displayed.
3. Press ENTER to change the DVR control mode.
4. Use the DVR function keys to control the DVR.

15
PRESET 000 PTZ
• LOCK
Displays the lock menu to change the user
type or disable the system operation.
• SETUP
Displays the setup menu or cancels operation
on the setup menus. Use to return to the pre-
vious menu or mode.
• SEARCH
Displays the search menu.
• MAIN
Display the MAIN menu to set the screen
mode to full, 4, 6, 8, 9 or 16 screens.
• SPOT
Enter SPOT mode to allow spot monitor con-
trol.
• NUM
Switches to number entering mode in a menu.
• ALM.OFF
Cancels alarm activation and returns the
system to the condition before the alarm was
activated.
• OSD
Accesses or removes the System Control Bar.
• INFO
Displays or removes system information.
• LOG
Displays or removes the System Log List.
• MARK
Sets the mark point for recording search.
• COPY
Copies the recording data to an external
device.
• REC
Starts or stops instant recording.
How to instant recording
(1) Press the REC.
(2) Press the NUM and then press the chan-
nel button you want to record.
(3) Press ENTER to start recording. The
recording type indicator turns green on the
selected channel screen.
(4) If you stop the recording, repeat the step
(1) to (3) as the above.
• Playback control buttons
- X: Pauses playback.
- m: Search the recorded images in reverse
or skip the recorded images.
- bB: Playback or reverse playback of
recorded images.
- M: Forward search the recorded images
or skip the recorded images.
- x: Stops playback.
5. Press CLR to exit the DVR control mode.

16
Operation the connected cam-
era via the DVR
You can control the connected camera via the LG
DVR using the LKD1000 controller.
1. Follow steps 1 to 2 described in “Operation the
LG DVR”.
2. Use the Arrow (
B
/
b
) buttons to select the cam-
era and then press ENTER. The DVR/CAM ID
input menu will be displayed.
3. Enter the connected DVR/CAM ID to control the
camera connected to the DVR and then press
ENTER. The camera control menu will be dis-
played.
4. Use the Arrow (
B
/
b
) buttons to select the
"COMMUNICATION" option and press ENTER.
5. Set the desired options. (For more details, see
pages 26 to 28)
6. Use the camera control buttons and joystick to
control the camera.
Operation of the camera con-
nected to the LKD1000 control-
ler directly
You can control the camera connected to the
LKD1000 controller directly.
1. Select CAM (Camera) icon in the main menu and
then press ENTER. The camera ID input menu
will be displayed.
2. Enter the connected camera ID to control the
camera connected to the LKD1000 controller
directly and then press ENTER. The camera con-
trol menu will be displayed.
3. Use the Arrow (
B
/
b
) buttons to select the
"COMMUNICATION" option and press ENTER.
4. Set the desired options. (For more details, see
pages 26 to 28)
5. Use the camera control buttons and joystick to
control the camera.

17
Camera Control Menu
The Camera Control menu has several submenus.
All of these main menus are divided into submenus.
Camera Control menu overview
Main Menu Sub Menu Page
PRESET
Set Preset 17
Go To Preset 18
Tour 18
Edit Group 19
Group Tour 20
Clear Preset 21
Clear All Preset 21
Set Alarm Input 22
Set Alarm Output 22
AUTO PANNING Set Auto Panning 23
Run Auto Panning 24
PATTERN Record Pattern 24
Play Pattern 25
PRIVACY ZONE Set Zone Area 25
Display Zone Area 26
COMMUNICATION
Protocol 26
Baudrate 27
Parity Bit 27
Data Bit 28
Stop Bit 28
Sync Communication 28
CAMERA SETUP
Set Manual Focus
Speed 29
Go To PTZ Home
Position 29
Periodic PTZ Reset 30
PTZ Reset 30
Factory Reset 31
Notes:
The pictures used in the camera control menu are
based on DVR-camera menu.
Depending on protocol, some functions are not
activated. See page 33 for more details.
•
•
Preset Settings
Preset is the function to register camera monitoring
positions (pan, tilt and zoom positions) associated
with position numbers.
By entering the position numbers, you can set cam-
eras to the preset positions.
Note:
To activate this function, you need to register the pre-
set positions of camera.
To register preset positions
1. Select the [PRESET] icon and press ENTER.
The sub menu will appear.
2. Select [Set Preset] option then press ENTER.
The sub menu will appear.
3. By moving the joystick, move the camera to a
point you want.
4. Enter a [Preset No.] (0 to 127) you want to reg-
ister by pressing the numeric buttons then press
ENTER.
5. Enter a [Speed] (1 to 127) to move to the preset
position. Then press ENTER.
6. Enter a [Park Time] (holding time) (1 to 255).
Then press ENTER.
The position and its number are memorized for
later recall.
7. Repeat steps 3 to 6 to add additional position.
8. Press CLR to return to the previous menu.

18
Changing to Picture at Preset Position
The following function is available only with cameras
provided with the preset function.
The preset function makes the camera move to the
programmed preset position.
It is necessary to program preset positions for the
camera beforehand.
1. Select the [PRESET] icon and press ENTER.
The sub menu will appear.
2. Select [Go to Preset] option then press ENTER.
The sub menu will appear.
3. Use number buttons to enter the memorized pre-
set position’s index number then press ENTER.
The camera moves to the preset position and the
picture of the camera in that position appears on
the monitor.
To tour the preset positions
You can tour all preset positions.
1. Select the [PRESET] icon and press ENTER.
The sub menu will appear.
2. Select [Tour] option then press ENTER.
The sub menu will appear.
3. Press ENTER.
All registered preset positions in the camera will
be selected, and the camera position image will
be displayed on the active monitor.
4. Move the joystick to stop the tour.
Note:
After executing Preset Touring, Group Touring, Run
Auto Panning or Play Pattern operation, the ongoing
operation has to be stopped by moving the joystick
before executing any other operation. Failure to do
this can make the target camera not working as
intended.

19
To edit the group
You can create a group using preset positions that
are registered already. A maximum of 9 groups is
available.
1. Select the [PRESET] icon and press ENTER.
The sub menu will appear.
2. Select [Edit Group] option then press ENTER.
The sub menu will appear.
3. Enter the group number (1 to 9) then press
ENTER.
4. Select [Add Preset] or [Delete Preset] then press
ENTER.
5. Enter the preset number that is already registered
and press ENTER.
The preset number is added to the group or delet-
ed from the group.
6. Repeat step 5 to add or delete preset number.
Note:
The group related parameters differ depending on
cameras. So please refer to camera’s manual.
7. Press CLR to exit edit group mode.

20
To delete a group
You can delete a memorized group.
1. Follow steps 1 to 2 described in “To edit the
group”.
2. Enter the group number (1 to 9) then press
ENTER.
3. Select [Delete Group] then press ENTER.
The delete group menu is displayed.
4. Press ENTER.
The group will be deleted.
To tour the group
You can tour the group that is registered already.
1. Select the [PRESET] icon and press ENTER.
The sub menu will appear.
2. Select [Group Tour] option then press ENTER.
The sub menu will appear.
3. Use number buttons to enter the group number
that is already registered then press ENTER.
The camera moves to the preset position in the
group and the picture of the camera in that posi-
tion appears on the monitor.