Life Fitness Club Series User manual

CLUB SERIES SHOULDER PRESS
Part # 7142101
RevA Revision:10/13/031
ASSEMBLY INSTRUCTIONS

PARTS LIST
KE
Y
PART
#
DESCRIPTION QTY KE
Y
PART
#
DESCRIPTION QTY
1 71424xx TOWER 1 15 3102905 3/8 X 3-3/4” BOLT 4
1A 7142201 CABLE 1 16 3102924 3/8 X 1-3/4” BOLT 2
1B 6692601 3 X 2 END CAP 4 17 3202407 3/8 X 3-1/4” BUTTON HEAD BOLT 4
1C 6714901 GUIDE ROD BUSHING 2 18 6965801 AXLE 3
1D 3222801 4.5" PULLEY 3 19 3102807 3/8” LOW HEIGHT LOCK NUT 18
1E 6866701 3/8 RH WASHER 4 21 3102514 3/8” SAE WASHER 29
1F 68666XX CAP, RH-20 03 PLAT,02 WHT 4 22 6866701 3/8” RH WASHER 37
1G 3102933 3/8-16 X 2 BOLT 1 23 3203501 PILLOW BLOCK 2
1H 6480301 3/8 SPACER 4 24 6913801 WEIGHT STACK SELECTOR PIN 1
1I 3102903 3/8-16 X 2.5" BOLT 2 25 3108001 WEIGHT STACK CUSHION 2
1J 3102514 3/8 FLAT WASHER 2 26 6866601 BLACK RH CAP 2
1K 3102807 3/8-16 NYLOCK LOW HT NUT 3 27 3222001 1” SHAFT COLLAR 2
2 68950xx CROSS SUPPORT 1 28 6714901 GUIDE ROD BUSHING 2
3 70034xx PULLEY BRACKET 1 29 3222801 4-1/2” PULLEY 1
4 71430xx BOOM ASSEMBLY 1 30 6979401 PLACARD LABEL 1
4A 6967402 ASSY, SEAT ADJ 1 31 6986201 LANGUAGE PLACARD LABEL 1
4B 6897001 15 POS ADJ PLATE 1 32 3102915 3/8 X 3-1/4” BOLT 1
4C 6897101 ADJ PLATE 1 33 6887202 10 LB. WEIGHT PLATE (STD) 20
4D 3234301 SCREW 4 34 6888402 15 LB. WEIGHT PLATE (OPT) 10
4E 6912202 HINGE BLK 1 35 68769xx BACK PAD 1
5 71427xx ASSY CROSS BRACE 1 36 69131xx SEAT PAD 1
6 3116001 RUBBER BUMPER 1 37 6957001 WEIGHT STACK LABEL 1
7 6966802 COUNTER BALANCE 2 38 6923602 HEAD PLATE 1
8 68839xx GUIDE ROD SUPPORT 1 39 6912801 ACCORDIAN SLEEVE 2
9 69787xx ASSY SHOULDER ARM 1 40 3230701 STARLOCK WASHER 4
9A 3103110 RUBBER GRIP 2 41 6866602 WHITE RH CAP 35
10 6927001 GUIDE ROD 2 OR 6866603 PLATINUM RH CAP 35
11 3102901 3/8 X 1-1/4” BOLT 2 42 6861902 TOP COVER SHROUD 1
12 3102903 3/8 X 2-1/2” BOLT 5 43 6862102 FRONT SIDE SHROUD BLK 2
13 3102922 3/8 X 2-3/4” BOLT 3 44 6862007 FRONT PLATINUM SHROUD 1
14 3102904 3/8 X 3” BOLT 2 45 6925202 FULL REAR SHROUD ASSY 1
OPTION* 6921602 ASSY FULL FRONT 1
*For all 5 digit part numbers you need to add the color at the end. **Language placard kit comes with Dutch, French,
For shrouds and weldments please use the following codes: German, Poruguese, Spanish, Japaneese, and
xxxxx07 Denotes Platinum Italian.
xxxxx08 Denotes White
*For upholstery, please use the following codes:
#02ROYAL BLUE
#03SLATE
#04CRANBERRY
#05NORTHWOODS
#06 SPACE BLUE
#07AMERICAN BEAUTY RED
#08SUEDE
#12 BLACK
#13HUNTER GREEN
#14 REGIMENTAL BLUE
#15GINGERSNAP
#16CONCORD
#17URQUOISE
#18 RASPBERRY
#19CROCUS

1
(2X)
(4X)
(4X)
(2X)
(2X)
(3X)
(4X)
(4X)
(3X)
1B
1C
1D
1I
1F
1K
1G
1J
1A
1K
1E
1H

STEP 1:
FIGURE 1
4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• LOOSELY assemble the CROSS SUPPORT (2) to theTOWER (1) and the BOOMASSEMBLY(4) using eight RH CAPS (41), four
3/8 X 3-3/4” BOLTS (15), eight 3/8” SAE WASHERS (21), eight 3/8” RH WASHERS (22) and four 3/8” LOW HEIGHT LOCK
NUTS (19) as shown in FIGURE 1.
15 3/8 X 3-3/4”
2
19
4
1
41
21
22
1A

5
FIGURE 2
STEP 2:
•Securely tighten all loose frame connections made to this point and sanp on all RH CAPS (28,41)
and RH WASHERS (22).
• LOOSELY assemble the CROSS BRACE (5) to the TOWER (1) and the BOOMASSEMBLY(4) using seven RH CAPS (41), three
3/8 X 2-3/4” BOLTS (13), one 3/8 X 2-1/2” BOLT (12), seven 3/8” SAE WASHERS (21), seven 3/8” RH WASHERS (22) and
three 3/8” LOW HEIGHT LOCK NUTS (19) as shown in FIGURE 2.
19
13 3/8 X 2-3/4”
4
5
1
21
22
41
12 3/8 X 2-1/2”
13 3/8 X 2-3/4”
4E
4D
4C
4B
4A
1A

6
0123456
1/2 1/2 1/2 1/2 1/2 1/2
FIGURE 4
• Slide two ACCORIDIAN SLEEVES (39) over the shafts on the BOOMASSEMBLY (4) as shown in FIGURE 4.
STEP 4:
4
23
• Carefully route the CABLE around the pulleys as shown. Make sure the CABLE is in the grooves of all the pulleys.
STEP 3:
FIGURE 3 CABLE
• Slide two PILLOW BLOCKS (23) over the shafts on the BOOM ASSEMBLY (4) as shown in FIGURE 4.
39
17 3/8 X 3-1/4”
BUTTONHEAD
40
• Assemble four 3/8 X 3-1/4” BUTTON HEAD CAP SCREWS (17) and four STARLOCK WASHERS (40) to the the PILLOW
BLOCKS (23) as shown in FIGURE 4
1A

7
STEP 5:
FIGURE 5
• IMPORTANT! When SHOULDERARM (9) is centered and level in the PILLOWBLOCKS (23), tighten the PILLOW BLOCK set
screws.
• SECURELY assemble the PILLOW BLOCKS (23) to the SHOULDER ARM (9) using four previously inserted 3/8 X 3-1/4”
BUTTON HEAD CAP SCREWS (17), four 3/8” SAE WASHERS (21), four RH WASHERS (22), four 3/8” LOW HEIGHT
LOCK NUTS (19) and four RH CAPS (41) as shown in FIGURE 5
17 3/8 X 3-1/4”
BUTTONHEAD
19
21
22
41
23
9
STEP 6:
FIGURE 6
• SECURELY assemble one RUBBER BUMPER (6) to the BOOM ASSEMBLY (4) and the SHOULDER ARM (9) as shown in
FIGURE 6.
TIGHTEN!
6
9
4
9A
1A 9A

8
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP 7:
FIGURE 7
• SECURELY assemble the PULLEY BRACKET (3) to the SHOULDER ARM (9) using one 3/8 X 1-3/4” BOLT (16), two 3/8”
SAE WASHERS (21), two RH WASHERS (22), one AXLE (18), one 3/8” LOW HEIGHT LOCK NUTS (19) and two RH CAPS
(41) as shown in FIGURE 7
16 3/8 X 1-3/4”
9
3
22
21
19
41
9A

9
STEP 8:
FIGURE 8
3
3/8 X 3-1/4” 32
22
4
29
19
41
21
• SECURELY assemble the two PULLEY BRACKETS (3) and one 4-1/2” PULLEY (29) to the bracket on the BOOM ASSEMBLY
(4) using one 3/8 X 3-1/4” BOLT (32), two 3/8” SAE WASHERS (21), two RH WASHERS (22), two AXLES (18), one 3/8”
LOW HEIGHT LOCK NUT (19) and two RH CAPS (41) as shown in FIGURE 8.
18

10
STEP 9:
FIGURE 9
• Assemble the swivel end of the CABLE to the SHOULDERARM (9) using one 3/8 X 1-3/4” BOLTS (16), two 3/8” SAE WASHERS
(21), two RH WASHERS (22), one 3/8” LOW HEIGHT LOCK NUT (19) and two RH CAPS (41) as shown in FIGURE 9. (NOTE:
Allow CABLE swivel end to rotate.)
• Carefully route the CABLE around the pulley as shown. Make sure the CABLE is in the grooves of all the pulley.
41
22 21
3/8 X 1-3/4” 16
9
19
0123456
1/2 1/2 1/2 1/2 1/2 1/2
CABLEDIAGRAM
CABLE
1A