Life Fitness Lifecycle upright 9500HR User manual

Life Fitness Model 9500HR Treadmills
How to…Install the Support Plate on Damaged Frame Cross-Member/Bracket
Tools required: Hex Key Wrench Set, Socket Set, C-Clamps, Phillips Screwdriver GK26-00002-0063
NOTE: STEPS 1-12 cover Belt, Deck, and Wax Bag Removal.
1. Turn the unit power OFF, then unplug the POWER CORD at the electrical outlet.
2. Remove the front and rear FRAME CAPS on the right side of the unit.
3. Remove the right HANDRAIL FOOT COVER.
4. Remove the mounting bolts
securing right HANDRAIL to
the frame.
5. Before loosening the
STRIDING BELT,
mark the location of the
BELT TENSIONING BOLTS
or record the number of turns
for proper belt re-tensioning.
6. Loosen the STRIDING
BELT by turning the BELT
TENSIONING BOLTS
counterclockwise.
7. Carefully tilt the unit on its left side (user's left) and
remove the rear ROLLER GUARD.
8. Cover the end of the stationary
leg to protect the striding belt
during removal.
9. Remove the striding belt.
10. Carefully tilt the unit back to its
upright, normal operating position.
11. Remove the DECK SCREWS and
DECK.
12. Pinch-off the wax hose and
remove the WAX COVER, BAG,
and TRAY.
Mounting Bolts (4)
Frame
Washer (4)
Wax Bag
Tray
Cover

Life Fitness Model 9500HR Treadmills
How to…Install the Support Plate on Damaged Frame Cross-Member/Bracket
NOTE: STEPS 13-16 cover LIFT ACTUATOR REMOVAL
and ASSESSEMENT OF DAMAGE to THE FRAME
CROSS-MEMBER.
13. Unplug the LIFT ACTUATOR from the WIRE
HARNESS.
14. Remove the upper nut, bolt, and washer
securing the ACTUATOR NUT
BRACKETS together. Loosen the lower
nut, bolt, and washer and lift out the
actuator nut past the bracket pins.
With the lift motor out, DO NOT turn
the adjusting screw. This will alter the incline
and decline setting.
15. At the non-threaded end of the LIFT
ACTUATOR, remove the HAIRPIN CLIP and
CLEVIS PIN and lift out the actuator motor.
16. Assess the damage to the cross-member and welded
bracket. Make repairs as necessary to restore back to
original location.
NOTE: STEPS 17-20 cover FRAME CROSS-MEMBER repairs
and installation of the SUPPORT PLATE.
17. Once the cross-member is restored, position the pre-drilled
SUPPORT PLATE on the inside channel of the CROSS-
MEMBER and use as a template in drilling eight holes in the
cross-member. Secure the support plate into position with
two C-Clamps at the locations shown. Make sure to
match-up the square hole in the plate with the square
hole in the cross-member.
18. Using the 9/32" and 11/32" drill bits provided, drill holes
in the cross-member in the sequence illustrated. Use the
9/32" drill bit for bracket holes (1,2,3,4) and the 11/32"
drill bit on the outer ends of the support plate (5,6,7,8).
19. After the first hole in the sequence is drilled, tighten the
plate with a bolt, washer, and nut to secure the cross-
member for proper hole alignment. Drill the next hole in
sequence and, when completed, fasten with bolt, washer
and nut and tighten. Complete drilling the remaining
holes, and install bolt, washer, nut and tighten.
20. Install the lift motor in reverse order of removal. If the lift
actuator screw was turned, refer to STEPS 21-24.
Hair Pin
Clip
Bracket
(Welded to
Cross-Member)
Cross-Member
(Welded to
Bracket)
Clevis
Pin
Nut, Bolt,
Washer(2)
Pin
Actuator
Nut Bracket
Actuator
Nut
Actuator
Screw
Actuator Motor
Pin
Cross-Member
(Cracked and
Bent)
Bracket
Square
Hole
Clamp
Location
Clamp
Location
#2 (9/32”)
#5 (11/32”)
#6 (11/32”)
Support Plate
clamped
into position
#1 (9/32”)
#7 (11/32”)#3 (9/32”) #4(9/32”)
#8 (11/32”)
Support
Plate
Flat
Washer
Hex
Nut
Cross-Member
Bolt BracketSquare
Hole

Life Fitness Model 9500HR Treadmills
How to…Install the Support Plate on Damaged Frame Cross-Member/Bracket
NOTE: STEPS 21-24 cover how to adjust the lift actuator screw if moved or if incline error message is
displayed.
21. Test the unit. If an incline error occurs then proceed to adjust the actuator screw.
22. With the unit on its left side, disconnect the lift frame from the lift actuator nut, enter 919 into the SERVICE
MENU (this will require that power to the unit be restored and the unit powered up). Press HILL + Manual
Programs and using the incline down arrow key, lower the lift motor untill it stops. Press the LIFT FRAME
ASSEMBLY tightly against the RUBBER STOPS on the bottom of the frame.
23. Check that the location of the mounting PINS in the LIFT ACTUATOR NUT BRACKET are centered in the slot. If
not, turn the LIFT ACTUATOR NUT accordingly to achieve this result.
24. Re-attach the lift actuator nut to the lift frame bracket.
NOTE: STEPS 25 and 26 cover DECK and STRIDING BELT installation.
25. Upright the unit and install the DECK and deck srews in the reverse order of removal.
26. Install the striding belt in reverse order of removal making sure arrows on the underside of the belt point in the
direction of belt rotation (see illustration). Refer to BELT TENSIONING and TRACKING ALIGNMENT below.
NOTE: STEPS 27-30 cover BELT TRACKING ALIGNMENT and TENSIONING (STALL TEST) on USED belts.
IMPORTANT: It is CRITICAL that the treadmill be correctly leveled prior to any belt tensioning or tracking
adjustments. An unstable unit can effect belt tracking.
27. After the treadmill has been leveled, plug the power cord back into an electrical wall outlet and activate the unit.
28. Tension the belt to the markings on the adjusting screws. Set the main motor speed to 4.0 mph (6.4 km/h) and
note belt tracking. If the belt moves to the left, turn the left adjusting bolt 1/4 turn clockwise and the right
adjusting bolt 1/4 turn counterclockwise to bring the belt back to center. If the STRIDING BELTmoves to the
right, turn the right adjusting bolt 1/4 turn clockwise and the left adjust bolt 1/4 turn counterclockwise to bring the
striding belt tracking back to center.
29. Repeat this adjustment until the striding belt is centered on the rear roller. Allow the unit to operate for several
minutes to ensure it remains on center.
30. Decrease striding belt speed to 2 mph (3.2 kph) and begin walking on the treadmill. Tightly grasp the handrails
and attempt to stall the striding belt. If it slips, stop the treadmill and increase belt tension by turning the
tensioning bolts clockwise in 1/4 turn increments. Repeat the stall test.
Belt
Adjusting
Bolts

Life Fitness Model 9500HR Treadmills
How to…Install the Support Plate on Damaged Frame Cross-Member/Bracket
NOTE: STEPS 31-33 cover BELT TENSIONING on NEW belts.
31. Prior to belt tensioning, place two pieces of tape 50” apart on the left and on the right edges of the striding belt
as illustrated.
32. Alternately tighten the two tensioning bolts 1/4 turn clockwise until the belt stretches so that the distance
between the tapes increases to 50.25”.
33. Adjust tracking as described on previous page.
NOTE: STEPS 34-36 complete reassembly.
34. Carefully turn the unit on its left side (user left) and install the rear roller guard.
35. Carefully upright the unit and install the front and rear frame caps on the right side of the unit.
36. Secure the RIGHT HANDRAIL to the FRAME using the two mounting bolts previously removed.
37. Re-install the RIGHT HANDRAIL FOOT COVER.
50”
M051-00K26-A264