Life Fitness T5-5 User manual

Treadmill User Manual: T5-0, T5-5, & T7-0
ASSEMBLY INSTRUCTIONS
TSeries
T
LIFEFITNESS.COM
Life Fitness offers a full line of premier fitness equipment for the home.
LIFECYCLE EXERCISE BIKES | TREADMILLS | TOTAL-BODY ELLIPTICAL CROSS-TRAINERS | STAIRCLIMBERS | GYM SYSTEMS
Where does your workout take you?
Check the Hardware List
1
Hardware Needed
Actual Size
A
B
Item Qty Description
A12 M10 x 25mm long hex head bolt
B12 M10 internal tooth star washers
C2 #10 x 1/2" phillips self tapping screws
D4 #6 x 3/8" long phillip screws
E1 Hex key wrench
© 2005 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is a trademark of Brunswick Corporation. CO-039-05 (09.05)
AB
2
3
Remove the top of the cardboard box. Pull out the console
uprights and console bridge and remove plastic wrapping.
Tear down front lip of bottom box. Lift the treadmill by the
rear tread roller and wheel forward off of the bottom box.
Remove the (2) screws securing
the front of the motor cover to the
front of the treadmill base. Lift the
front of the motor cover and slide
it forward, detaching the motor
cover from the back clips. Set the
motor cover and screws aside.
Bolt the left upright to the treadmill base
using (4) M10 x 25mm bolts and (4) M10
internal tooth washers as shown. Repeat
the procedure to attach the right upright.
Finger tighten the (8) bolts at this time.
Warning: Do not lift treadmill with forklift.
Warning: Do not lift treadmill by console.
OK59-01311-0000
PM-009-05 insturctions 9/27/05 9:18 AM Page 1

Using (2) #10 x 1/2" Phillips screws from
the top and (4) #6 x 3/8 Phillips screws
from the bottom, secure the bridge cover
to the bridge/console assembly. Be sure
to align the edges of the top and bottom
covers before tightening the screws.
Tighten the screws securely but do not
over tighten them.
AB
C
D
C
E
Actual Size
Actual Size
Actual Size
Level the treadmill using the leveling feet (A). Once the treadmill is level, lock the feet in place with the jam nuts.
If necessary, use the provided hex key wrench to center the striding belt. See
How to Center the Striding Belt page in
the
How To section of the user manual (B).
Feed one end of the console cable down through the center hole of the right upright (A) and then out the bottom
cable access hole as shown (B). Carefully pull approximately 18" of cable through the cable access hole and connect
the cable jack to the motor controller board as shown (B). Connect the remaining cable jack (near the bridge assembly)
to the console board located at the bottom of the display console (A). Route the console cable through the cable clips
as shown. Feed any excess cable into the center hole of the right upright.
5
A
6
47
8
9
A
Hardware Needed
Hardware Needed
Hardware Needed
Hardware Needed
B
B
Bolt the bridge/console assembly to the
uprights using (4) M10 x 25mm bolts and
(4) M10 internal tooth washers as shown.
Tighten the (4) bolts securely.
Now tighten the bottom (8) upright bolts
(from step 3) securely.
Insert the water bottle holders and CD tray
into their respective locations as shown.
Press firmly to ensure they are fully seated.
Re-install the motor cover.
With the front of the motor
cover tilted upward, slide the
motor cover into the clips and
lower the front down to the
frame. Secure the motor
cover using the (2) previously
removed screws. Tighten the
screws securely but do not
over tighten them.
PM-009-05 insturctions 9/27/05 9:19 AM Page 2