Life Gear Formula II 20280 User manual

FORMULA II ,
MAGNETIC UPRIGHT BIKE
ITEM NO: 20280
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2014, Dec.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 1
SAFETY INSTRUCTIONS ------------------------------------------------------------- 2
PARTS LIST ------------------------------------------------------------------------------- 3
HARDWARE PACKING LIST --------------------------------------------------------- 4
TOOLS -------------------------------------------------------------------------------------- 4
OVERVIEW DRAWING ----------------------------------------------------------------- 5
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 6
OPERATING THE COMPUTER ------------------------------------------------------ 10
ADJUSTMENTS -------------------------------------------------------------------------- 12
MAINTENANCE -------------------------------------------------------------------------- 13
TROUBLESHOOTING ------------------------------------------------------------------ 13
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 14
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing, free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment. Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 60x30x2 1 030 Cap Nut M8 4
002 Front Stabilizer Ø60x1.5x350 1 031 Flywheel Ø230x40xØ32 1
003 Rear Stabilizer Ø60x1.5x430 1 032 Bearing Cup 2
004 Idle Wheel Bracket 1 033 Bearing 6000ZZ 2
005 Seat Post 60x20x1.8 1 034 Bearing Nut I 15/16" 1
006 Adjustable Leveler M10 2 035 Bearing Nut II 7/8" 1
007 Handlebar Post Ø50x1.5 1 036 Washer Ø24xØ40xδ3 1
008 Handlebar Ø25x1.5x1000 1 037 Washer Ø23xØ34.5xδ2.5 1
009 Tension Bracket 2 038 Hexagon Nut 7/8" 1
010 Washer Ø8xØ16x1.5 7 039 Belt Pulley with Crank Ø240J6 1
011 Eyebolt M8x85 1 040 Bolt M5x45 1
012 Rear Left Stabilizer End Cap
Ø60x1.5
1 041 Big Curve Washer Ø5xØ15x1 1
013 Rear Right Stabilizer End Cap
Ø60x1.5
1 042 Bolt M5x10 4
014 Big Curve Washer Ø8xØ20x2 4 043 Handlebar Foam Grip
Ø30xØ24x455
2
015 Big Curve Washer Ø8xØ25 4 044 Left Foot Pedal YH-30X 1
016 Spring Washer Ø6 2 045 Right Foot Pedal YH-30X 1
017 Bolt M8x70 4 046 Handlebar End Cap Ø25x1.5 2
018 Hexagon Nut M10 2 047 Cover Cap Ø40xØ25x10 2
019 Bolt M8x15 6 048 Seat Post Knob M16x1.5 1
020 Bolt M8x20 1 049 Hand Pulse Sensor with Wire
L=750mm
2
021 Eyebolt M6x36 2 050 Sensor with Wire L=750mm 1
022 Idle Wheel Ø10xØ35 1 051 Left Cover 543x376x85 1
023 Screw ST2.9x12 2 052 Right Cover 543x376x82 1
024 Screw ST4.2x20 4 053 Seat Post Bushing 1
025 Screw ST4.2x25 7 054 Tension Control Knob 1
026 Pan Head Phillips Self Drilling
Screw ST4.2x25
4 055 Tension Cable L=900mm 1
027 Nylon Nut M8 7 056 Front Left Stabilizer End Cap
Ø60x1.5
1
028 Hexagon Nut M6 2 057 Front Right Stabilizer End Cap
Ø60x1.5
1
029 Nut M10x1x10 2 058 Handlebar Post Cover Ø50x1.5 1

4
PARTS LIST
No. Description Qty No. Description Qty
059 Seat Post Cover 60x20x1.5 1 062 Computer HR-1586 1
060 Belt PJ 350 J6 1 063 Extension Sensor Wire (L=900mm) 1
061 Seat Cushion DD-982AT 1 064 Curve Washer Ø16xØ8x1.5 2
HARDWARE PACKING LIST
TOOLS
(30) Cap Nut M8
4 PCS
(17) Bolt M8x70
4 PCS
(15) Big Curve Washer
Ø8xØ25
4 PCS
Allen Wrench S6
1 PC
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
1 PC

5
OVERVIEW DRAWING
61
3
18
6
18
6
13
12
30
15
38
37
35 33 32
32 33 34 36
39
60
45
44 30
15
53
59
48
5
10
27
58
57
2
56
24
23
50
63
130
15
17
26
26
26
26
52
47
51
47
24
17
55
54
7
41
40
62
63
8
49
24
49
24
46
46
64
19
42
43
43
31
21 29
9
28 16
21
29
9
16
4
20
22
10
28
11
10
27
19
19
14
14 19
14
25
25

6
ASSEMBLY INSTRUCTIONS
1. Front and Rear Stabilizers Installation
Position the Front Stabilizer (2) in front of Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Main Frame (1) with two M8x70
Bolts (17), two Ø8xØ25 Big Curve Washers (15), and two M8 Cap Nuts (30). Tighten cap
nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Install two Adjustable Levelers (6) with two M10 Hexagon Nuts (18) onto the Rear Stabilizer
(3).
Position the Rear Stabilizer (3) behind the Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (3) onto the rear curve of the Main Frame (1) with two M8x70
Bolts (17), two Ø8xØ25 Big Curve Washers (15), and two M8 Cap Nuts (30). Tighten cap
nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
30
15
18
6
17
18
6
15
30
1
30
15
17
2
3
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Tool:
4 Cap Nuts (M8)4 Bolts (M8x70) 4 Big Curve Washers
(Ø8xØ25)

7
2. Seat Cushion and Seat Post Installation
Remove three M8 Nylon Nuts (27) and three Ø8xØ16x1.5 Washers (10) and from underside
of the Seat Cushion (61). Remove nylon nuts with the Multi Hex Tool with Phillips
Screwdriver provided.
Guide bolts on underside of the Seat Cushion (61) through holes on top of the Seat Post (5),
attach with three removed M8 Nylon Nuts (27) and three Ø8xØ16x1.5 Washers (10).
Tighten nylon with the Multi Hex Tool with Phillips Screwdriver provided.
Slide the Seat Post Cover (59) onto the Main Frame (1). Insert the Seat Post (5) into the
Seat Post Bushing (53).
Adjust the seat position and insert the M16x1.5 Seat Post Knob (48). Turn the M16x1.5
Seat Post Knob (48) in the clockwise direction to tighten.
53
59
48
61
10
27
5
1
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Tool:

8
3. Handlebar Post, Tension Control Knob, and Foot Pedals Installation
Remove four M8x15 Bolt (19) and four Ø8xØ20x2 Big Curve Washers (14) from the Main
Frame (1). Remove bolts with the S6 Allen Wrench provided.
Slide the Handlebar Post Cover (58) up to the Handlebar Post (7).
Insert the Tension Cable (55) through into the bottom hole of Handlebar Post (7) and pull it
out from the square hole of Handlebar Post (7).
Connect the Sensor Wire (50) from the Main Frame (1) to the Extension Sensor Wire (63)
from the Handlebar Post (7).
Insert the Handlebar Post (7) onto the tube of the Main Frame (1) and secure with four
M8x15 Bolt (19) and four Ø8xØ20x2 Big Curve Washers (14) that were removed. Tighten
bolts with the S6 Allen Wrench provided. Slide the Handlebar Post Cover (58) down to the
Main Frame (1).
Remove the M5x45 Bolt (40) and Ø5xØ15x1 Big Curve Washer (41) from the Tension
Control Knob (54). Remove bolt with the Multi Hex Tool with Phillips Screwdriver provided.
Put the cable end of resistance cable of Tension Control Knob (54) into the spring hook of
Tension Cable (55) as shown in drawing A of figure 3. Pull the resistance cable of Tension
Control Knob (54) up and force it into the gap of metal bracket of Tension Cable (55) as
shown in drawing B of figure 3. Attach the Tension Control Knob (54) onto the Handlebar
Post (7) with the M5x45 Bolt (40) and Ø5xØ15x1 Big Curve Washer (41) that were removed.
Tighten bolt with the Multi Hex Tool with Phillips Screwdriver provided.
Foot Pedals Installation
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Allen Wrench S6
Tool:
54
54
41
41
40
40
63
63
19
19
19
19
14
14
14
14
19
19
14
14
58
58
55
55
50
50
7
39
39
45
45
44
44
1
54
54
55
55
54
54
55
55
BA

9
Insert the pedal shaft of Left Foot Pedal (44) into threaded hole in the left Crank (39).
Turn the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (44) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (45) into threaded hole in right Crank (39).
Turn the pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (45) with the Multi Hex Tool with Phillips Screwdriver
provided.
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
4. Handlebar and Computer Installation
Remove two M8x15 Bolts (19) and two Ø16xØ8x1.5 Curve Washers (64) from the
Handlebar Post (7). Remove bolts with the S6 Allen Wrench provided.
Insert the Hand Pulse Sensor Wires (49) into the hole on the Handlebar Post (7) and then
pull them out from the top end of the Handlebar Post (7).
Attach the Handlebar (8) onto the Handlebar Post (7) with two M8x15 Bolts (19) and two
Ø16xØ8x1.5 Curve Washers (64) that were removed. Tighten bolts with the S6 Allen
Wrench provided.
Remove four M5x10 Bolts (42) from the Computer (62). Remove bolts with the Multi Hex
Tool with Phillips Screwdriver provided.
Connect the Hand Pulse Sensor Wires (49) and Extension Sensor Wire (63) to the wires that
come from the Computer (62). Tuck wires into the Handlebar Post (7).
Attach the Computer (62) onto the top end of the Handlebar Post (7) with four M5x10 Bolts
(42) that were removed. Tighten bolts with the Multi Hex Tool with Phillips Screwdriver
provided.
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Allen Wrench S6
Tool:
62
8
42
63
49
19
7
49
64