Life Gear 20250 User manual

STRAIGHT
MAGNETIC UPRIGHT BIKE
ITEM NO: 20250
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2013, Dec.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWAREAND TOOLS PACK ---------------------------------------------------- 5
OVERVIEW DRAWING -----------------------------------------------------------------6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
OPERATING THE COMPUTER ------------------------------------------------------ 12
ADJUSTMENTS -------------------------------------------------------------------------- 13
MAINTENANCE -------------------------------------------------------------------------- 14
TROUBLESHOOTING ------------------------------------------------------------------ 14
WARM UPAND COOL DOWN ROUTINE ----------------------------------------- 15

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 1 029 Rear Stabilizer End Cap Ø50 2
002 Handlebar 1 030 FlywheelAxle Ø15 1
003 Handlebar Post 1 031 Bearing 6000Z 2
004 Rear Stabilizer 1 032 Spring Clip Ø10 1
005 Flywheel Ø180x25 1 033 Hexagon Nylon Nut M6 1
006 Front Stabilizer Ø50x1.5x360 1 034 Cap Nut M10 2
007 Tension Control Knob 1 035 Bolt M10x56 2
008 Seat Post Knob M12x1.75 1 036 Curve Washer Ø20xØ10.5x2 2
009 Belt PJ4/270 1 037 Curve Washer Ø16xØ8x1.5 6
010 Computer HTL-C006 1 038 Washer Ø8 8
011 Magnet Plate 1 039 Hexagon Head Bolt M8x20 1
012 Seat Post Bushing 1 040 Cross Recessed Pan Head
Tapping Screw ST4.2x25 7
013 Left Cover 1 041 Spring Ø20x36x3.2 1
014 Cross Recessed Pan Head Bolt
M5x12 2 042 Hexagon Nylon Nut M8 4
015 Cross Recessed Pan Head
Tapping Screw ST2.9x9.5 2 043 Hexagon Head Bolt M6x20 1
016 Washer Ø40x2.8 1 044 IdlerArm 1
017 Bearing Nut I (7/8") 1 045 Bearing 6002Z 2
018 Hexagon Nut 7/8” 1 046 Screw ST4.2x25 4
019 Belt Pulley with Crank PJ6/Ø200 1 047 Washer Ø6 1
020 Left Foot Pedal YH-2X 1 048 Washer Ø35x2 1
021 Right Foot Pedal YH-2X 1 049 Handlebar End Cap 2
022 Bearing Cup Ø55.6x16 2 050 Handlebar Foam Grip 2
023 Ball Bearing Ø44.5 2 051 Right Cover 1
024 Hexagon Socket Pan Head Cap
Bolt M8x15 11 052 Wave Washer Ø15.2xØ20x1 1
025 Seat Post 1 053 Spring Ø10xØ1x53 1
026 Sensor with Wire L=600 mm 1 054 Tension Cable 1
027 Seat Cushion DD-98-11T 1 055 Hexagon Nut M6 1
028 Front Stabilizer End Cap Ø50 2 056 Cross Recessed Pan Head
Tapping Screw ST4.2x20 2

5
PARTS LIST
HARDWARE AND TOOLS PACK
No. Description Qty No. Description Qty
057 Cross Recessed Pan Head Bolt
M5x45 1 063 Washer Ø10 1
058 Bearing Nut II (15/16") 1 064 Curve Washer Ø5 1
059 Extension Sensor Wire L=800 mm 1 065 Hand Pulse Sensor with Wire
L=600 mm 2
060 Big Washer Ø24xØ8.4x2 1 066 Cover Cap Ø50xØ28 1
061 Washer Ø5xØ9x0.8 2 067 Handlebar Post Ring Cap 1
062 Washer Ø21xØ15.2x3 1 068 Seat Post Ring Cap 1
Allen Wrench S6
1 PC Multi Hex Tool with Phillips Screwdriver S13-14-15
1 PC
Multi Hex Tool
S13-17-19
1 PC
(8) Seat Post Knob
M12x1.75
1 PC
(35) Bolt M10x56
2 PCS (36) Curve Washer Ø20xØ10.5x2
2 PCS
(34) Cap Nut M10
2 PCS

6
OVERVIEW DRAWING
46
46
59
59
65
65
54
54
66
66
66
66
37
37
24
24
50
50
65
65
64
64
63
63
62
62
61
61
61
61
60
60
59
59
58
58
56
56
56
56
55
55
54
54
53
53
52
52
21
21
20
20
51
51
50
50
49
49
48
48
47
47
40
40
40
40
46
46
45
45
44
44
43
43
42
42
42
42
41
41
40
40
39
39
24
24
24
24
38
38
38
38
37
37
35
35
33
33
32
32
31
31
30
30
29
29
28
28
27
27
26
26
26
26
25
25
24
24
24
24
23
23
22
22
23
23
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
8
7
6
5
4
3
2
67
67
68
68
29
29
1
31
31
36
36
34
34
28
28
46
46
57
57
65
65
49
49

7
ASSEMBLY INSTRUCTIONS
1. Front and Rear Stabilizers Installation
Position the Front Stabilizer (6) in front of the Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (6) onto the front curve of the Main Frame (1) with two M10 Cap
Nuts (34), two M10x56 Bolts (35), and two Ø20xØ10.5x2 Curve Washers (36). Tighten cap
nuts with the Multi Hex Tool provided.
Remove five M8x15 Hexagon Socket Pan Head Cap Bolts (24) and five Ø8 Washers (38)
from the Rear Stabilizer (4). Remove bolts with the S6 Allen Wrench provided.
Insert the Rear Stabilizer (4) into the tube of the Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (4) into the tube of the Main Frame (1) with five M8x15 Hexagon
Socket Pan Head Cap Bolts (24) and five Ø8 Washers (38) that were removed. Tighten
bolts with the S6 Allen Wrench provided.
Hardware:
Tool:
Multi Hex Tool
S13-17-19
Allen Wrench S6
(35) Bolt M10x56
2 PCS (36) Curve Washer Ø20xØ10.5x2
2 PCS
(34) Cap Nut M10
2 PCS

8
2. Left and Right Foot Pedals Installation
The Cranks, Pedal Shafts, and Foot Pedals are marked “R” for Right and “L” for Left.
Insert the pedal shaft of Left Foot Pedal (20) into threaded hole in the left Crank (19). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (20) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (21) into threaded hole in right Crank (19). Turn the
pedal shaft by hand in the clockwise direction until snug. Tighten pedal shaft of Right Foot
Pedal (21) with the Multi Hex Tool with Phillips Screwdriver provided.
Multi Hex Tool with Phillips Screwdriver
S13-14-15
Tool:

9
3. Handlebar Post Installation
Remove four M8x15 Hexagon Socket Pan Head Cap Bolts (24) and four Ø16xØ8x1.5 Curve
Washers (37) from the tube of the Main Frame (1). Remove bolts with the S6 Allen Wrench
provided.
Connect the Sensor Wire (26) from the Main Frame (1) to the Extension Sensor Wire (59)
from the Handlebar Post (3).
Put the cable end of resistance cable of Tension Control Knob (7) into the cable lock of
Tension Cable (54), see Figure A.
Pull the resistance cable of Tension Control Knob (7) up and force it into the slot of metal
bracket of Tension Cable (54), see Figure B.
Insert the metal fitting on the resistance cable of Tension Control Knob (7) into the hole at the
end of the slot in the metal bracket of Tension Cable (54), see Figure C.
Connect the resistance cable of Tension Control Knob (7) to Tension Cable (54) complete,
see Figure D.
Insert the Handlebar Post (3) onto the tube of the Main Frame (1) and secure with four
M8x15 Hexagon Socket Pan Head Cap Bolts (24) and four Ø16xØ8x1.5 Curve Washers (37)
that were removed. Tighten bolts with the S6Allen Wrench provided.
Allen Wrench S6
Tool:
A
B
C
D

10
4. Seat Cushion, Seat Post, and Seat Post Knob Installation
Remove three Ø8 Washers (38) and three M8 Hexagon Nylon Nuts (42) from underside of
the Seat Cushion (27). Remove hexagon nylon nuts with the Multi Hex Tool with Phillips
Screwdriver provided. Guide bolts on underside of the Seat Cushion (27) through holes on
top of the Seat Post (25), attach with three removed Ø8 Washers (38) and three M8
Hexagon Nylon Nuts (42). Tighten hexagon nylon nuts with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert the Seat Post (25) into the Seat Post Bushing (12) on the tube of the Main Frame (1)
and then attach the Seat Post Knob (8) onto the tube of the Main Frame (1) by turning it in a
clockwise direction to lock the Seat Post (25) in the suitable position.
Multi Hex Tool with Phillips Screwdriver
S13-14-15
Tool:

11
5. Handlebar and Computer Installation
Remove two M8x15 Hexagon Socket Pan Head Cap Bolts (24) and two Ø16xØ8x1.5 Curve
Washers (37) from the Handlebar Post (3). Remove bolts with the S6 Allen Wrench
provided.
Insert the Hand Pulse Sensor Wires (65) into the hole on the Handlebar Post (3) and then
pull them out from the top end of the Handlebar Post (3).
Attach the Handlebar (2) onto the Handlebar Post (3) with two M8x15 Hexagon Socket Pan
Head Cap Bolts (24) and two Ø16xØ8x1.5 Curve Washers (37) that were removed.
Tighten bolts with the S6 Allen Wrench provided.
Remove two M5x12 Cross Recessed Pan Head Bolts (14) from the Computer (10).
Remove bolts with the Multi Hex Tool with Phillips Screwdriver provided.
Connect the Extension Sensor Wire (59) and Hand Pulse Sensor Wires (65) to the wires that
come from the Computer (10). Tuck wires into the Handlebar Post (3). Attach the
Computer (10) onto the top end of the Handlebar Post (3) with two M5x12 Cross Recessed
Pan Head Bolts (14) that were removed. Tighten bolts with the Multi Hex Tool with Phillips
Screwdriver provided.
59
59
14
14
10
10
65
65
2
24
24
37
37
3
65
65
Allen Wrench S6
Tool:
Multi Hex Tool with Phillips Screwdriver
S13-14-15

12
OPERATING THE COMPUTER
SPECIFICATIONS:
TIME --------------------------------------------------- 0:00-99:59 MIN: SEC
SPEED ------------------------------------------------ 0.0-999.9 KM/H
DISTANCE ------------------------------------------- 0.0-999.9 KM
CALORIES ------------------------------------------- 0.0-999.9 KCAL
ODOMETER ----------------------------------------- 0.00-99.99 KM
PULSE ------------------------------------------------ 40-240 BEATS/MIN
USING YOUR COMPUTER
The computer can be activated by pressing the button or by pedaling. If you leave the
equipment idle for 4-5 minutes, the power will turn off automatically.
BUTTON FUNCTIONS:
Press the button to select one of the seven functions of the computer.
Press and hold the button for 3 seconds to reset all data values to zero except the
ODOMETER data values.
COMPUTER FUNCTIONS:
SCAN: Automatically scans each function in sequence with change every 4 seconds.
NOTE: If you do not want to use the SCAN function, press the button to select one of the
other functions.
TIME: Displays your elapsed workout time in minutes and seconds.
SPEED: Displays the current training speed.
DISTANCE: Displays the cumulative distance traveled during workout.
CALORIES: Displays approximate amount of calories burned during workout.
(This data is a rough guide for comparison of different exercise sessions and should not be
used in medical treatment).
ODOMETER: Displays the total accumulative distance traveled. The ODOMETER data
values can not be clear to zero by pressing and holding the button for 3 seconds. If you
take out the batteries from the computer, the ODOMETER data values will clear to zero.
PULSE: Displays your current heart rate figures after you grip the handlebar pulse sensors
with both your hands during exercise. To ensure the pulse readout is more precise, please
always hold on to the handlebar pulse sensors with two hands instead of just with one hand
only when you try to test your heart rate figures.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover on the back of the computer.
2. Place two size AAA batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are in proper contact with
batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial segment appears, remove batteries and wait 15
seconds before reinstalling.

13
ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the tension, turn the tension control knob in a
clockwise direction.
To decrease the tension, turn the tension control knob in a
counterclockwise direction.
Adjusting the Rear Stabilizer End Cap
Turn the rear stabilizer end cap on the rear stabilizer as
needed to level the upright bike.
Adjusting the Seat Height
Turn the seat post knob in a counterclockwise direction
until the seat post can be slid up or down and then slide the
seat post up or down direction to the suitable position.
Lock the seat post in place by tightening the seat post knob
in a clockwise direction.
NOTE: When adjusting the height of seat post, make
sure the seat post bushing does not exceed the mark
line on the seat post.
Tension Control Knob
Rear Stabilizer End Cap
Seat Post Knob

14
MAINTENANCE
Cleaning
The upright bike can be cleaned with a soft clean damp cloth. Do not use abrasives or
solvents on plastic parts. Please wipe your perspiration off the upright bike after each use.
Be careful not to get excessive moisture on the computer display panel as this might cause
an electrical hazard or electronics to fail.
Please keep the upright bike, especially the computer console out of direct sunlight to
prevent screen damage.
Please inspect all assembly bolts, nuts, screws, and pedals on the machine for proper
tightness every week.
Storage
Store the upright bike in a clean and dry environment away from children.
TROUBLESHOOTING
PROBLEM SOLUTION
The upright bike wobbles when in use. Turn the rear stabilizer end cap on the rear
stabilizer as needed to level the upright bike.
There is no display on the computer
console.
1. Remove the computer console and verify
the wires that come from the computer
console are properly connected to the
wires that come from the handlebar post.
2. Check if the batteries are correctly
positioned and battery springs are in
proper contact with batteries.
3. The batteries in the computer console may
be dead. Replace with new batteries.
There is no heart rate reading or heart rate
reading is erratic / inconsistent.
1. Make sure that the wire connections for
the hand pulse sensors are secure.
2. To ensure the pulse readout is more
precise, please always hold on to the
handlebar grip sensors with both hands
instead of just with one hand when you try
to test your heart rate figures.
3. Avoid gripping the hand pulse sensors too
tight. Try to maintain moderate pressure
while holding onto the hand pulse sensors.
The upright bike makes a squeaking noise
when in use. The bolts may be loose on the upright bike. Please inspect all of the bolts and tighten any
loose bolts.

15
WARM UP AND COOL DOWN ROUTINE
The WARM-UP is an important part of any workout. The purpose of warming up is to
prepare your body for exercise and to minimize injuries. Warm up for two to five minutes
before aerobic exercising. It should begin every session to prepare your body for more
strenuous exercise by heating up and stretching your muscles, increasing your circulation
and pulse rate, and delivering more oxygen to your muscles.
COOL DOWN at the end of your workout, repeat these exercises to reduce soreness in tired
muscles. The purpose of cooling down is to return the body to its resting state at the end of
each exercise session. A proper cool-down slowly lowers your heart rate and allows blood
to return to the heart.
HEAD ROLLS
Rotate your head to the right for one count, you should feel a
stretching sensation up the left side of your neck. Then rotate your
head back for one count, stretching your chin to the ceiling and
letting your mouth open. Rotate your head to the left for one count,
then drop your head to your chest for one count.
SHOULDER LIFTS
Lift your right shoulder toward your ear for one count. Then lift your
left shoulder up for one count as you lower your right shoulder.
SIDE STRETCHES
Open your arms to the side and lift them until they are over your head.
Reach your right arm as far toward the ceiling as you can for one
count. Repeat this action with your left arm.

16
QUADRICEPS STRETCH
With one hand against a wall for balance, reach behind you and pull
your right foot up. Bring your heel as close to your buttocks as
possible. Hold for 15 counts and repeat with left foot.
HAMSTRING STRETCHES
Extend your right leg. Rest the sole of your left foot
against your right inner thigh. Stretch toward your toe
as far as possible. Hold for 15 counts. Relax and then
repeat with left leg.
CALF/ACHILLES STRETCH
Lean against a wall with your left leg in front of the right and
your arms forward. Keep your right leg straight and the left
foot on the floor; then bend the left leg and lean forward by
moving your hips toward the wall. Hold, then repeat on the
other side for 15 counts.
TOE TOUCHES
Slowly bend forward from your waist, letting your back and
shoulders relax as you stretch toward your toes. Reach as far as
you can and hold for 15 counts.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees pointing
outward. Pull your feet as close to your groin as possible.
Gently push your knees toward the floor. Hold for 15 counts.