Life Gear MERCURY 26570 User manual

MERCURY,
MAGNETIC RECUMBENT BIKE
ITEM NO: 26570
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2014, Oct.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST --------------------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 5
OVERVIEW DRAWING -----------------------------------------------------------------6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 14
MAINTENANCE -------------------------------------------------------------------------- 15
TROUBLESHOOTING ------------------------------------------------------------------ 15
WARM UPAND COOL DOWN ROUTINE ----------------------------------------- 16

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Pan Head Phillips Self Drilling
Screw ST4.2x18 5 023 Bolt M8x15 9
002 Screw ST4.2x18 4 024 Washer Ø5xØ10 1
003 Cover Cap 2 025 Bolt M5x40 1
004L Left Cover 1 026 Front Handlebar Post 1
004R Right Cover 1 027 Front Main Frame 1
005L Left Foot Pedal 1 028 Big Curve Washer Ø8xØ20 3
005R Right Foot Pedal 1 029 Computer (XLG-501) 1
006 Belt Pulley with Crank 1 030 Bolt M5x10 4
007 Nut 7/8” 1 031 Tension Control Knob 1
008 Washer Ø7/8” 1 032 Front Handlebar Foam Grip
Ø24xØ30x160 2
009 Bearing Nut II 7/8” 1 033 Handlebar End Cap Ø25.4x1.5 4
010 Bearing 2 034 Rear Handlebar Foam Grip
Ø24xØ30x510 2
011 Belt 330J6 2 035 Carriage Bolt M10x57 4
012 Cap Nut M8 6 036 Washer Ø10xØ4x0.8 2
013 Washer Ø22xØ10x1.5t 4 037 Screw ST3.8x20 2
014 Bearing Cup Ø56x22.5x68 2 038 Bolt M6x15 8
015 Bearing Nut I 15/16” 1 039 Rear Main Frame 1
016 Washer Ø15/16” 1 040A Extension Sensor Wire 1
017 Transport Wheel Ø23xØ6x32 2 040B Sensor with Wire 1
018 Bolt M6x48 2 041 Bolt M6x10 1
019 Bolt M8x45 2 042 Nut M10x7t 2
020 Front Handlebar Post Cover 1 043 Eyebolt M6 2
021 Wire Grommet Ø12 2 044 Tension Bracket 2
022A Extension Hand Pulse Sensor
Wire A 1 045 Nylon Nut M6 4
022B Extension Hand Pulse Sensor
Wire B 1 046 Flywheel Ø190 1
022C Extension Hand Pulse Sensor
Wire C 1 047 Round Knob M16 1
022D Hand Pulse Sensor with Wire 2 048 Bearing 6000Z 2

5
PARTS LIST
No. Description Qty No. Description Qty
049 Washer Ø8xØ16 9 059 Back and Seat Support Bracket 1
050 Rubber Cover 1 060 Back Cushion 1
051 Back and Seat Support Bracket
End Cap 38x38x1.5 2 061 Seat Cushion 1
052 Idler Arm 1 062 Rear Stabilizer End Cap Ø50 2
053 Sensor Bracket 1 063 Front Stabilizer End Cap Ø50 2
054 Bolt M8x10 1 064 Rear Stabilizer 1
055 Rear Handlebar 1 065 Cap Nut M10 4
056 Tension Cable 1 066 Bolt M8x30 1
057 Big Washer Ø6xØ16 9 067 Bushing 1
058 Front Stabilizer Ø50 1 068 Plug for Rear Main Frame 1
HARDWARE PACKING LIST
TOOLS
Allen Wrench 5mm
1 PC
Multi Hex Tool
1 PC
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15
1 PC
(12) Cap Nut M8
4 PCS (13) Washer Ø22xØ10x1.5t
4 PCS (23) Bolt M8x15 4 PCS
(35) Carriage Bolt M10x57
4 PCS (49) Washer Ø8xØ16 4 PCS
(65) Cap Nut M10
4 PCS

6
12
11
15
16
51
51
59
38
33
57
57
38
61
60
4L
3
2
1
2
56
26
49
40A
25
29
24
22A
30 31
32
33
20
40B
28
49 23
45
58
17
18
63
5L
5R
6
14 10 3
1
4R
78910 14
1
46
42
43
44
45
53
41
66
52
54
49
48
57
27
50
22B
47
22C
39
23
21
65
13
36
34
37
21
22D
19
28
55
62
35
64
12
49
62
13
65
34
35
23
32
33
23
22D
67
68
OVERVIEW DRAWING

7
ASSEMBLY INSTRUCTIONS
1. Front and Rear Stabilizers Installation
Turn the Round Knob (47) in a counterclockwise direction until it can be pulled out. Pull out
the Round Knob (47) and then slide the Rear Main Frame (39) forth or back direction to the
suitable position. Lock the Rear Main Frame (39) in place by releasing the Round Knob (47)
and sliding the Rear Main Frame (39) forth or back slightly until the Round Knob (47)
"pops" down into the locked position. For added safety, tighten the Round Knob (47) in a
clockwise direction.
Position the Front Stabilizer (58) in front of the Front Main Frame (27) and align bolt holes.
Attach the Front Stabilizer (58) onto the front curve of the Front Main Frame (27) with two
M10x57 Carriage Bolts (35), two Ø22xØ10x1.5t Washers (13), and two M10 Cap Nuts (65).
Tighten cap nuts with the Multi Hex Tool provided.
Position the Rear Stabilizer (64) behind the Rear Main Frame (39) and align bolt holes.
Attach the Rear Stabilizer (64) onto the rear curve of the Rear Main Frame (39) with two
M10x57 Carriage Bolts (35), two Ø22xØ10x1.5t Washers (13), and two M10 Cap Nuts (65).
Tighten cap nuts with the Multi Hex Tool provided.
Hardware:
(13) Washer Ø22xØ10x1.5t
4 PCS (35) Carriage Bolt M10x57
4 PCS (65) Cap Nut M10 4 PCS
65
13
13
65
47
13
65
58
35
39
35
64
27
Tool:
Multi Hex Tool

8
2. Back and Seat Support Bracket Installation
Attach the Back and Seat Support Bracket (59) onto the Rear Main Frame (39) with four
M8x15 Bolts (23), four Ø8xØ16 Washers (49), and four M8 Cap Nuts (12). Tighten bolts
and cap nuts with the 5mm Allen Wrench and Multi Hex Tool with Phillips Screwdriver
provided.
Hardware:
23
39
59
12
49
Tool:
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15
Allen Wrench 5mm
(12) Cap Nut M8
4 PCS (23) Bolt M8x15
4 PCS
(49) Washer Ø8xØ16
4 PCS

9
3. Rear Handlebar Installation
Remove two M8x45 Bolts (19), two Ø8xØ20 Big Curve Washers (28), and two M8 Cap Nuts
(12) from the Rear Handlebar (55). Remove bolts and cap nuts with the 5mm Allen
Wrench and Multi Hex Tool with Phillips Screwdriver provided.
Attach the Rear Handlebar (55) onto the Back and Seat Support Bracket (59) with two
M8x45 Bolts (19), two Ø8xØ20 Big Curve Washers (28), and two M8 Cap Nuts (12) that
were removed. Tighten bolts and cap nuts with the 5mmAllen Wrench and Multi Hex Tool
with Phillips Screwdriver provided.
Connect the Hand Pulse Sensor Wires (22D) from the Rear Handlebar (55) to the Extension
Hand Pulse Sensor Wires C (22C) from the Rear Main Frame (39).
12
22D
19
28
55
22C
59
Tool:
Allen Wrench 5mm
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15