Life Gear 26460 User manual

SWANY,
MAGNETIC RECUMBENT BIKE
ITEM NO: 26460
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2013, June

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST --------------------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 5
OVERVIEW DRAWING ----------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 15
MAINTENANCE -------------------------------------------------------------------------- 16
TROUBLESHOOTING ------------------------------------------------------------------ 16
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 17

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001L Front Left Stabilizer End Cap 1 025 Spring Washer Ø6 2
001R Front Right Stabilizer End Cap 1 026 Hexagon Nut M6 2
002L Left Cover KD006-0400-002 1 027 Extension Sensor Wire L=550 1
002R Right Cover KD006-0400-003 1 028 Hexagon Nut 7/8" 1
003 Front Stabilizer Ø60x1.5 1 029 Washer I 7/8” 1
004 Pan Head Phillips Self Drilling
Screw ST4.2x20 6 030 Bearing Nut II 7/8" 1
005 Bolt M8x70 4 031 Ball Bearing 2
006 Computer HR-1583 1 032 Bearing Cup 2
007 Curve Washer Ø20xØ5.2 1 033 Bearing Nut I 15/16" 1
008 Cross Recessed Pan Head Bolt
M5x12 4 034 Washer II 15/16” 1
009 Cross Recessed Pan Head Bolt
M5x45 1 035L Left Foot Pedal 1"/2 1
010 Front Handlebar Post Ø50x1.5 1 035R Right Foot Pedal 1"/2 1
011 Front Handlebar Foam Grip
Ø24xØ30x160 2 036 Belt Pulley with Crank 6.5″1
012 Handlebar End Cap Ø25.4x1.5 4 037 Bolt M6x10 1
013 Tension Control Knob 1 038 Big Washer Ø16xØ6x1.5 1
014 Front Handlebar Post Cover 1 039 Bearing 6000z 2
015 Hexagon Socket Pan Head Bolt
M8x15 18 040 Idler Arm 1
016 Big Curve Washer Ø8xØ25x2 10 041 Hexagon Socket Pan Head Bolt
M8x20 1
017 Front Main Frame Ø50x1.5 1 042 Cross Recessed Pan Head
Tapping Screw ST4.2x25 10
018 Cap Nut M8 6 043 Hexagon Socket Pan Head Bolt
M8x10 1
019 Cover Cap Ø50xØ26x10 2 044 Bushing 2
020 Nut M10x1x10 2 045 Washer Ø8xØ16x1.5 17
021 Belt PJ350 J6 1 046 Rear Main Frame 1
022 Flywheel Ø230x40xØ32 1 047L Rear Left Main Frame Cover 1
023 Eyebolt M6x45 2 047R Rear Right Main Frame Cover 1
024 Tension Bracket 2 048 Rear Stabilizer Ø60x1.5x558 1

5
PARTS LIST
HARDWARE PACKING LIST
TOOLS
No. Description Qty No. Description Qty
049L Rear Left Stabilizer End Cap Ø60 1 061 Rear Handlebar Foam Grip
Ø24xØ30x550 2
049R Rear Right Stabilizer End Cap
Ø60 1 062 Hexagon Socket Pan Head Bolt M8x45 2
050 Adjustable Leveler M10x38 2 063 Handlebar Ø25x1.5x1294 1
051 Hexagon Nut M10 2 064 Hand Pulse Sensor with Wire
L=750 2
052 Back and Seat Support Bracket
End Cap 23x53x2 1 065 Extension Hand Pulse Sensor Wire III L=550 2
053 Triangle Knob M12 1 066 Tension Cable L=900 1
054 Round Knob M16 1 067 Extension Hand Pulse Sensor
Wire II L=1150 2
055 Seat Sliding Tube 53x23x2.0x440 1 068 Sensor with Wire L=400 1
056 Back and Seat Support Bracket
53x23x2.0x446 1 069 Extension Hand Pulse Sensor Wire I L=1100 1
057 Hexagon Socket Pan Head Bolt
M6x15 8 070 Cross Recessed Pan Head Self Drilling Screw ST2.9x12 1
058 Big Washer Ø6xØ18x1.5 8 071 Cross Recessed Pan Head
Tapping Screw ST4.2x20 2
059 Seat Cushion DD-PVC214C 1 072 Wire Grommet Ø12 2
060 Back Cushion DD-PVC215C 1
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15
1 PC
Allen Wrench 5mm
1 PC
(5) Bolt M8x70
4 PCS
(16) Big Curve Washer
Ø8xØ25x2
4 PCS
(18) Cap Nut M8
4 PCS

6
OVERVIEW DRAWING

7
ASSEMBLY INSTRUCTIONS
1. Rear Main Frame and Front/Rear Stabilizers Installation
Remove six M8x15 Hexagon Socket Pan Head Bolts (15) and six Ø8xØ16x1.5 Washers (45)
from the Rear Main Frame (46). Remove bolts with the 5mm Allen Wrench provided.
Connect the Extension Hand Pulse Sensor Wires I (69) from the Rear Main Frame (46) to
the Extension Hand Pulse Sensor Wires II (67) from the Front Main Frame (17).
Insert the Rear Main Frame (46) into the Front Main Frame (17) and secure using six M8x15
Hexagon Socket Pan Head Bolts (15) and six Ø8xØ16x1.5 Washers (45) that were removed.
Tighten bolts with the 5mm Allen Wrench provided.
Position the Front Stabilizer (3) in front of the Front Main Frame (17) and align bolt holes.
Attach the Front Stabilizer (3) onto the front curve of the Front Main Frame (17) with two
M8x70 Bolts (5), two Ø8xØ25x2 Big Curve Washers (16), and two M8 Cap Nuts (18).
Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Position the Rear Stabilizer (48) behind the Rear Main Frame (46) and align bolt holes.
Attach the Rear Stabilizer (48) onto the rear curve of the Rear Main Frame (46) with two
M8x70 Bolts (5), two Ø8xØ25x2 Big Curve Washers (16), and two M8 Cap Nuts (18).
Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
Allen Wrench 5mm
Tools:
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15
(5) Bolt M8x70
4 PCS
(16) Big Curve Washer
Ø8xØ25x2
4 PCS
(18) Cap Nut M8
4 PCS

8
2. Seat Sliding Tube, Back/Seat Support Bracket, and Seat/Back Cushions Installation
Remove eight M8x15 Hexagon Socket Pan Head Bolts (15) and eight Ø8xØ16x1.5 Washers
(45) from the Seat Sliding Tube (55). Remove bolts with the 5mm Allen Wrench provided.
Insert the Seat Sliding Tube (55) into the Bushings (44) of the Rear Main Frame (46).
Attach the Back and Seat Support Bracket (56) onto the Seat Sliding Tube (55) with eight
M8x15 Hexagon Socket Pan Head Bolts (15) and eight Ø8xØ16x1.5 Washers (45) that were
removed. Tighten bolts with the 5mm Allen Wrench provided.
Adjust the seat position and align knob holes. Insert the Round Knob (54) and Triangle
Knob (53) into knob holes. Turn the Round Knob (54) and Triangle Knob (53) in the
clockwise direction to tighten.
Remove eight M6x15 Hexagon Socket Pan Head Bolts (57) and eight Ø6xØ18x1.5 Big
Washers (58) from the back of the Seat and Back Cushions (59, 60). Remove bolts with
the 5mm Allen Wrench provided. Then attach the Seat and Back Cushions (59, 60) onto
the Back and Seat Support Bracket (56) with eight M6x15 Hexagon Socket Pan Head Bolts
(57) and eight Ø6xØ18x1.5 Big Washers (58) that were removed. Tighten bolts with
the5mm Allen Wrench provided.
Allen Wrench 5mm
Tool:

9
3. Handlebar Installation
Remove two M8x45 Hexagon Socket Pan Head Bolts (62), two Ø8xØ25x2 Big Curve
Washers (16), two Ø8xØ16x1.5 Washers (45), and two M8 Cap Nuts (18) from the
Handlebar (63). Remove bolts and cap nuts with the 5mm Allen Wrench and Multi Hex Tool
with Phillips Screwdriver provided.
Attach the Handlebar (63) onto the Back and Seat Support Bracket (56) with two M8x45
Hexagon Socket Pan Head Bolts (62), two Ø8xØ25x2 Big Curve Washers (16), two
Ø8xØ16x1.5 Washers (45), and two M8 Cap Nuts (18). Tighten bolts and cap nuts with the
5mm Allen Wrench and Multi Hex Tool with Phillips Screwdriver provided.
Connect the Hand Pulse Sensor Wires (64) from the Handlebar (63) to the Extension Hand
Pulse Sensor Wires I (69) from the Rear Main Frame (46).
Allen Wrench 5mm
Tools:
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15