Life Gear METEOR User manual

METEOR,
MAGNETIC UPRIGHT BIKE
ITEM NO: 20590
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2014, Dec.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST --------------------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 5
OVERVIEW DRAWING ----------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
OPERATING THE COMPUTER ------------------------------------------------------ 12
ADJUSTMENTS -------------------------------------------------------------------------- 14
MAINTENANCE -------------------------------------------------------------------------- 15
TROUBLESHOOTING ------------------------------------------------------------------ 15
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 16

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise is necessary.
Refer to the Warm Up and Cool Down Routine pages. After exercise, relaxation of the
body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 1 031 Flywheel Ø230x40 1
002 Front Stabilizer Ø60x1.5tx380 1 032 Bearing Cup 2
003 Rear Stabilizer Ø60x1.5tx480 1 033 Ball Bearing 2
004 Idler Arm 1 034 Bearing Nut I 15/16” 1
005 Seat Post 1 035 Bearing Nut II 7/8” 1
006 Seat Sliding Tube 1 036 Washer Ø24xØ40x3t 1
007 Handlebar Post 1 037 Washer Ø23xØ34.5x2.5t 1
008 Handlebar Ø25 1 038 Hexagon Nut 7/8” 1
009 Tension Bracket 2 039 Belt Pulley with Crank 1
010 Washer Ø8xØ16x1.5t 7 040 Bolt M5x20 1
011 Screw ST2.9x16 1 041 Washer Ø5xØ15x1.0t 1
012 Front Left Stabilizer End Cap
Ø60 1 042 Bolt M5x10 4
013 Front Right Stabilizer End Cap
Ø60 1 043 Handlebar Foam Grip Ø24xØ30x490 2
014 Curve Washer Ø8xØ20x1.5t 4 044 Left Foot Pedal YH-30X 1
015 Seat Adjustment Knob M10 1 045 Right Foot Pedal YH-30X 1
016 Spring Washer Ø6 2 046 Handlebar End Cap Ø25 2
017 Carriage Bolt M8x70 2 047 Cover Cap Ø40xØ25x10 2
018 Square End Cap □38 2 048 Seat Post Knob M16x1.5 1
019 Bolt M8x15 2 049 Hand Pulse Sensor with Wire
L=750mm 2
020 Bolt M8x30 1 050 Sensor with Wire L=750mm 1
021 Eyebolt M6x36 2 051 Left Cover 1
022 Bearing 60002Z 2 052 Right Cover 1
023 Screw ST2.9x12 2 053 Seat Post Plastic Bushing 1
024 Screw ST4.2x20 4 054 Tension Control Knob 1
025 Screw ST4.2x25 8 055 Tension Cable L=1150 1
026 Pan Head Phillips Self Drilling
Screw ST4.2x25 4 056 Clamp Cover 1
027 Nylon Nut M8 3 057 Spacer (Ø12x20) 1
028 Nut M6 2 058 Handlebar Post Cover 1
029 Nut M10x6t 2 059 Seat Post Cover 1
030 Cap Nut M8 2 060 Belt PJ370 J6 1

5
PARTS LIST
HARDWARE PACKING LIST
TOOLS
No. Description Qty No. Description Qty
061 Seat Cushion (DD-982AT) 1 069 Washer Ø8xØ20x2t 1
062 Computer (HR-1581) 1 070 Bolt M8x10 3
063 Extension Sensor Wire
L=950mm 1 071 Rear Left Stabilizer End Cap Ø60 1
064 Handlebar T-Knob (M8x55) 1 072 Rear Right Stabilizer End Cap Ø60 1
065 Washer Ø12xØ6x1t 1 073 Hexagon Nut M10x6t 2
066 Bolt M6x10 1 074 Adjustable Leveler M10 2
067 Wire Grommet Ø12.1 1 075 Bolt M8x70 2
068 Seat Sliding Tube Bolt 1 076 Washer Ø14xØ10xδ1.0 2
Multi Hex Tool
1 PC
Multi Hex Tool with Phillips Screwdriver
1 PC
Allen Wrench S6
1 PC
(14) Curve Washer
Ø8xØ20x1.5t
4 PCS
(17) Carriage Bolt M8x70
2 PCS
(30) Cap Nut M8
2 PCS
(75) Bolt M8x70
2 PCS

6
OVERVIEW DRAWING
23
10
32
33
35
37
38
31
21
29
51
26
47
26
12
2
13
58
53
50
59
5
15
69
18
68
27
61
54
64
55
7
57
56
62
52
60
45
39
44
36
34
33
32
48
1
72
73
74
73
74
71
43
8
43
49
46
24
24
2816 9
28 16 9
17
24
14 30
41
40
21
66
22
4
18
25
25
26
47
26
42
67
10
70 19
10
75
3
6
65
63
20
70
11
49
70
29
14
76

7
ASSEMBLY INSTRUCTIONS
1. Front/Rear Stabilizers and Left/Right Foot Pedals Installation
Position the Front Stabilizer (2) in front of the Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Main Frame (1) with two M8x70
Carriage Bolts (17), two Ø8xØ20x1.5t Curve Washers (14), and two M8 Cap Nuts (30).
Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Position the Rear Stabilizer (3) behind the Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (3) onto the rear curve of the Main Frame (1) with two M8x70
Bolts (75) and two Ø8xØ20x1.5t Curve Washers (14). Tighten bolts with the S6 Allen
Wrench provided.
Install two M10 Adjustable Levelers (74) with two M10x6t Hexagon Nuts (73) onto the Rear
Stabilizer (3).
Foot Pedals Installation
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Insert the pedal shaft of Left Foot Pedal (44) into threaded hole in the left Crank (39). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (44) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (45) into threaded hole in right Crank (39). Turn the
pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (45) with the Multi Hex Tool with Phillips Screwdriver
provided.
Hardware:
(14) Curve Washer
Ø8xØ20x1.5t
4 PCS
(17) Carriage Bolt M8x70
2 PCS
(30) Cap Nut M8
2 PCS
(75) Bolt M8x70
2 PCS
Allen Wrench S6
Tool:
Multi Hex Tool with Phillips Screwdriver
14
30
17
75
74
73
73
74
45
44
13
2
14

8
2. Seat Post, Seat Post Cover, Seat Cushion, and Seat Sliding Tube Installation
Slide the Seat Post Cover (59) onto the tube of the Main Frame (1). Insert the Seat Post
(5) into the Seat Post Plastic Bushing (53) on the tube of the Main Frame (1) and then attach
the Seat Post Knob (48) onto the tube of the Main Frame (1) by turning it in a clockwise
direction with Multi Hex Tool provided to lock the Seat Post (5) in the suitable position.
Remove three M8 Nylon Nuts (27) and three Ø8xØ16x1.5t Washers (10) from underside of
the Seat Cushion (61). Remove nylon nuts with the Multi Hex Tool with Phillips
Screwdriver provided.
Guide bolts on underside of the Seat Cushion (61) through holes on top of the Seat Sliding
Tube (6), attach with three removed M8 Nylon Nuts (27) and Ø8xØ16x1.5t Washers (10).
Tighten nylon nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Guide the Seat Sliding Tube Bolt (68) on underside of the Seat Sliding Tube (6) through hole
on top of the Seat Post (5), attach with one Ø8xØ20x2t Washer (69) and Seat Adjustment
Knob (15).
27
10
1
48
59
5
15
69
6
61
53
Multi Hex Tool with Phillips Screwdriver
Multi Hex Tool
Tool:

9
3. Handlebar Post, Handlebar Post Cover, and Tension Control Knob Installation
Remove four M8x10 Bolts (70) and four Ø8xØ16x1.5t Washers (10) from the Main Frame (1).
Remove bolts with the S6 Allen Wrench provided.
Slide the Handlebar Post Cover (58) up to the Handlebar Post (7).
Insert the Tension Cable (55) through into the bottom hole of Handlebar Post (7) and pull it
out from the square hole of Handlebar Post (7).
Connect the Sensor Wire (50) from the Main Frame (1) to the Extension Sensor Wire (63)
from the Handlebar Post (7).
Insert the Handlebar Post (7) onto the tube of the Main Frame (1) and secure with four
M8x10 Bolts (70) and four Ø8xØ16x1.5t Washers (10) that were removed. Tighten bolts
with the S6 Allen Wrench provided.
Slide the Handlebar Post Cover (58) down to the Handlebar Post (7).
Remove the M5x20 Bolt (40) and Ø5xØ15x1.0t Washer (41) from the Tension Control Knob
(54). Remove bolt with the Multi Hex Tool with Phillips Screwdriver provided.
Put the cable end of resistance cable of Tension Control Knob (54) into the spring hook of
Tension Cable (55), see Figure A. Pull the resistance cable of Tension Control Knob (54)
up and force it into the gap of metal bracket of Tension Cable (55), see Figure B. Attach the
Tension Control Knob (54) onto the Handlebar Post (7) with the M5x20 Bolt (40) and
Ø5xØ15x1.0t Washer (41) that were removed. Tighten bolt with the Multi Hex Tool with
Phillips Screwdriver provided.
63
41
40
54
10
70
10
19
AB
54
55
55
54
55
1
70
50
63
7
Allen Wrench S6
Tool:
Multi Hex Tool with Phillips Screwdriver