Life Gear 26290 User manual

EVOKE, RECUMBENT BIKE
ITEM NO.: 26290
Owner’s Manual
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change without
notice. 2013, Nov.

1
TABLE OF CONTENTS
WARRANTY-----------------------------------------------------------------1
SAFETY INSTRUCTIONS-----------------------------------------------2
ADJUSTMENTS------------------------------------------------------------3
OPERATING THE COMPUTER----------------------------------------3
PARTS LIST-----------------------------------------------------------------5
HARDWARE PACKING LIST------------------------------------------- 7
TOOLS------------------------------------------------------------------------7
OVERVIEW DRAWING-------------------------------------------------- 8
ASSEMBLY INSTRUCTIONS-------------------------------------------9
MAINTENANCE------------------------------------------------------------13
TROUBLESHOOTING----------------------------------------------------13
WARM UPAND COOL DOWN ROUTINE---------------------------14
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing, free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the load, turn the tension control knob in a clockwise direction.
To decrease the load, turn the tension control knob in a counterclockwise direction.
Adjusting the Rear Stabilizer End Cap
Turn the rear stabilizer end cap on the rear stabilizer as needed to level the recumbent bike.
Adjusting the Seat
Release the triangle knob from the rear main frame. Turn the round knob in a
counterclockwise direction until it can be pulled out. Pull out the round knob and then slide
the back and seat support bracket back or forth direction to the suitable position. Lock the
back and seat support bracket in place by releasing the round knob and sliding the back and
seat support bracket back or forth slightly until the round knob "pops" down into the hole of
the seat sliding tube. For added safety, tighten the round knob and triangle knob in a
clockwise direction.
NOTE: When adjusting the seat back or forth direction, the maximum insert depth
mark line cannot over than the edge of bushing.
OPERATING THE COMPUTER
USING YOUR COMPUTER
The computer can be activated by pressing the buttons or by
pedaling. If you leave the equipment idle for approximate 4 minutes,
the power will turn off automatically.
BUTTON FUNCTIONS:
MODE: Press the MODE button to select each function of computer.
Press and hold the MODE button for 3 seconds, all data values will clear to zero except the
ODO (ODOMETER) data values.
COMPUTER FUNCTIONS:
SCAN: Press the MODE button until the arrow points to the SCAN, the computer will
automatically scan each function every 6 seconds.
TIME: Press MODE button until the arrow points to the TIME, the computer will display your
elapsed workout time in minutes and seconds.
SPEED: Press MODE button until the arrow points to the SPEED, the computer will display
the current training speed.
DIST (DISTANCE): Press MODE button until the arrow points to the DIST, the computer will
display the accumulative distance traveled during workout.

4
CAL (CALORIES): Press MODE button until the arrow points to the CAL, the computer will
display the total accumulated calories burned during workout. (This data is a rough guide
for comparison of different exercise sessions and should not be used in medical treatment).
ODO (ODOMETER): Press MODE button until the arrow points to the ODO, the computer
will display the total accumulative distance traveled.
PULSE: Press MODE button until the arrow points to the PULSE, the computer will display
your current heart rate figures after you grip the handlebar sensors with both your hands
during exercise. To ensure the pulse readout is more precise, please always hold on to the
handlebar grip sensors with two hands instead of just with one hand only when you try to test
your heart rate figures.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover on the back of the computer.
2. Place two size AA batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are in proper contact with
batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial segment appears, remove batteries and wait 15
seconds before reinstalling.

5
PARTS LIST
No. Description Qty No. Description Qty
001 Back and Seat Support Bracket 1 029 Bolt M6x48 2
002 Front Stabilizer Ø50x1.5x430 1 030 Bolt M10x57 4
003 Rear Main Frame 1 031 Spring 1
004 Rear Stabilizer Ø50x1.5 1 032 Cap Nut M10 4
005 Front Main Frame 1 033 Left Cover 1
006 Front Handlebar Post Ø50x1.5 1 034 Right Cover 1
007 Seat Cushion 1 035 Screw ST4.2x20 2
008 Back Cushion 1 036 Bolt M5x45 1
009 Computer (HR-1582) 1 037 Nut M6 2
010 Handlebar Foam Grip
Ø24xØ30x450 2 038 Big Curve Washer Ø5 1
011 Hand Pulse Sensor with Wire
L=750 2 039 Bolt M5x10 4
012 Round End Cap for Handlebar
Ø25x1.5 4 040 Tension Cable L=900mm 1
013 Handlebar Ø25 1 041 Axle Bush 2
014 Tension Control Knob 1 042 Ball Bearing 2
015 Seat Sliding Tube 1 043 Axle Sleeve I 1
016 Screw ST4.2x25 9 044 Hexagon Nut 2
017 Round Knob M16x1.5 1 045 Ring 1
018 Cap Nut M8 2 046 Crank Ø240 1
019 Front Handlebar Foam Grip
Ø24xØ30x160 2 047 Flywheel Ø230 1
020 Nylon Nut M8 2 048 Idle Wheel Bracket 1
021 Bolt M6x15 8 049 Bolt M8x30 2
022 Backrest and Seat Support
Bracket End Cap 23x53x1.5 1 050 Nylon Nut M6 2
023 Bolt M8x15 16 051 Front Stabilizer End Cap 2
024 Washer Ø8 18 052 Spring Washer Ø6 2
025 Curve Washer Ø8 6 053 Nut M10x1 2
026 Big Curve Washer Ø10 4 054 Bushing 2
027 Wire Plug Ø12.1 2 055 Middle Section Hand Pulse Sensor
Wire 2
028 Bolt M8x18 1 056 Idle Wheel 1

6
PARTS LIST
No. Description Qty No. Description Qty
057 Rear Stabilizer End Cap 2 068 Cover Cap Ø50x10 2
058 Washer Ø6 8 069 Pan Head Phillips Self Drilling
Screw ST4.2x20 2
059 Right Foot Pedal 1 070 Bolt M8x45 2
060 Left Foot Pedal 1 071 Wheel 2
061 Sensor with Wire L=450mm 1 072 Axle Sleeve II 1
062 Belt 370J6 1 073 Washer 1
063 Extension Wire L=350mm 2 074 Front Handlebar Post Cover 1
064 Extension Sensor Wire
L=500mm 1 075 Left Rear Main Frame Cover 1
065 Extension Hand Pulse Sensor
Wire L=1800mm 2 076 Right Rear Main Frame Cover 1
066 Triangle Knob M12 1 077 Adjustable Bolt M6x36 2
067 Screw ST4.2x15 2 078 U Bracket 2

7
HARDWARE PACKING LIST
TOOLS
(18) Cap Nut M8
2 PCS (24) Washer Ø8 2 PCS (25) Curve Washer Ø8 2 PCS
(26) Curve Washer Ø10
4 PCS (30) Bolt M10x57 4 PCS (32) Cap Nut M10
4 PCS
(70) Bolt M8x45
2 PCS
Allen Wrench S6
1 PC Multi Hex Tool with Phillips Screwdriver
1 PC
Multi Hex Tool
1 PC

8
OVERVIEW DRAWING
11
13
70
25
35
10
12
11
27
22
1
35
11
8
7
23
24
18
24
24
23
21
58
58
21
15
23
24
57
4
75
69
16
32 26
30
21
58
24
23
54
55
17 27
54
69
76
66
57
3
19
12
19
12
9
64
63
14
40
64
6
36
38
39
59
34
68
33
16
16
68
2
51
29
71 50
30
29
71 51
62
46
60
72
41
42
73
63
74
32
26
23
25
23
65
61
44
43
41
42
45
53
37
77
78
52
53
77
5
32
26
67
61
47
37
52
78
49
23
23
24
24
55
31
48
28
56
20
24
65
21
10
12

9
ASSEMBLY INSTRUCTIONS
1. Rear Main Frame Installation
Remove two M8x30 Bolts (49), four M8x15 Bolts (23), and six Ø8 Washers (24) from the
Rear Main Frame (3).
Connect the Middle Section Hand Pulse Sensor Wires (55) from the Rear Main Frame (3) to
The Extension Hand Pulse Sensor Wires (65) from the Front Main Frame (5).
Attach the Rear Main Frame (3) into the Front Main Frame (5) with two M8x30 Bolts (49),
four M8x15 Bolts (23), and six Ø8 Washers (24) that were removed. Tighten bolts with the
Allen Wrench provided.
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
Hardware:
2. Front and Rear Stabilizers Installation
Position the Front Stabilizer (2) in front of the Front Main Frame (5) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Front Main Frame (5) with two
M10x57 Bolts (30), Ø10 Big Curve Washers (26), and M10 Cap Nuts (32). Tighten bolts
with the Multi Hex Tool provided.
Position the Rear Stabilizer (4) behind the Rear Main Frame (3) and align bolt holes.
Attach the Rear Stabilizer (4) onto the rear curve of the Rear Main Frame (3) with two
M10x57 Bolts (30), Ø10 Big Curve Washers (26), and M10 Cap Nuts (32). Tighten bolts
with the Multi Hex Tool provided.
49
23
65
55
3
55
24
24
5
24
23
65 61
Allen Wrench S6
Tool:
5
3
4
2
32
26
32
26
30
30
32 26
32 26
55
65 61
Multi Hex Tool
Tool:
4 Bolts ( M10x57)
4 Curve Washers (Ø10)
4 Cap Nuts (M10)