Life Gear 30640 User manual

AIR MAGNETIC ROWER
ITEM NO: 30640
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change
without prior notice. 2020, Dec.

1
TABLE OF CONTENTS
WARRANTY -------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST -------------------------------------------------------------------------------- 4
HARDWARE PACK ---------------------------------------------------------------------- 6
EXPLODED VIEW ------------------------------------------------------------------------ 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
STORAGE ---------------------------------------------------------------------------------- 14
MAINTENANCE --------------------------------------------------------------------------- 15
MOVING THE ROWER ------------------------------------------------------------------ 15
OPERATING THE COMPUTER ------------------------------------------------------ 16
ADJUSTMENTS --------------------------------------------------------------------------- 17
TROUBLESHOOTING ------------------------------------------------------------------- 19
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 20

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that
it has been installed and operated in accordance with LifeGear's Owner's Manual.
LifeGear's obligation under this warranty is limited to replacing or repairing free of charge,
any parts which may prove to be defective under normal home use. This warranty does
not include any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure
the equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid muscle injury, warm-up exercises are recommended.
3. Please make sure all parts are undamaged and properly secured. This equipment
should be placed on a flat surface when in use.
4. Please wear appropriate clothing and shoes when using this equipment. Do not wear
clothes that may catch any part of the machine and remember to tighten the pedaling
straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. This equipment is not suitable for therapeutic use.
7. Do not use the equipment outdoors.
8. This equipment is for household use only. It is not a commercial model.
9. Only one person at a time should use this equipment.
10. If you experience any chest pain, nausea, dizziness, or shortness of breath, you
should stop exercising immediately and consult your physician before continuing.
11. Care should be taken in mounting or dismounting the equipment.
12. This machine is designed for adult use only. Do not allow children to use or play on
the equipment at any time.
13. The minimum free space required for safe operation of this machine is two meters.
Keep children and pets away from the equipment while it is in use.
14. The maximum weight capacity for this product is 110 kg.
WARNING: Before beginning any exercise program consult your
physician. This is especially important for people who are over 35 years old or who
have pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Right Foot Pedal 1 031 Left Cover 1
002 Left Foot Pedal 1 032 Right Cover 1
003 Plastic Fan Plate Ø316x136 1 033 Sensor Bracket 29x15x9.4 1
004 Rolling Wheel Ø37x32 1 034 Handlebar Ø25.4x15.Tx560 1
005 Rear Stabilizer 1 035 Computer Console 1
006 Slide Tube 1008x110x48.2 1 036 Wire Clip Ø1/8” 2
007 Seat Plate 211.5x150x3T 1 037 EVA Rubber Pad 2
008 Strap and Pulley Set Ø128x142 1 038 Belt (280J6) 1
009 Front Stabilizer 40x80x1.5Tx420 1 039 Tension Control Knob with Wire 1
010 Magnet Bracket 1 040 Handlebar Foam Grip
Ø25.4x5Tx240 2
011 Main Frame 1 041 Sensor Wire A (L=350mm) 1
012 Support Slide Tube 210x81x30 1 042 Sensor Wire B (L=350mm) 1
013 Safety Pin Ø10x105 1 043 Hexagon Head Bolt M6x12 4
014 Foot Pedal Axle Ø12x466 (M8) 2 044 Carriage Bolt M8x55 2
015 Rolling Wheel Axle Ø10x40.4
(M6) 2 045 Nylon Nut M6 3
016 Hexagon Head Bolt M10x102 1 046 Nylon Nut M10 1
017 Magnet Bracket Axle Ø14x21.3 1 047 Flange Nut M10 2
018 Spring Ø9.4xØ1.0x50.0 1 048 Cap Nut M8 2
019 Eyebolt M6x38 2 049 Cross Recessed Truss Head Bolt
M6x25 4
020 Tension Bracket 25x9.5x9.5 2 050 Hexagon Socket Button Head
Bolt M8x20 12
021 Handlebar End Cap Ø33.6x27 2 051 Cross Recessed Truss Head Bolt
M5x10 1
022 Wheel Ø30x33.8 1 052 Cross Recessed Truss Head Bolt
M5x12 1
023 T Washer Ø17x4.2 2 053 Cross Recessed Truss Head Bolt
M6x45 1
024 Handlebar Plastic Cover 1 054 Cross Recessed Pan Head
Tapping Screw ST2.9x15 4
025 Front Handlebar Cover 1 055 Cross Recessed Pan Head
Tapping Screw ST4.2x20 2
026 Rear Handlebar Cover 1 056 Cross Recessed Truss Head
Tapping Screw ST4.2x10 2
027 Foot Stabilizer End Cap Ø38.1 2 057 Cross Recessed Truss Head
Tapping Screw ST4.2x15 8
028 Buffer Ø27x16 4 058 Cross Recessed Truss Head
Tapping Screw ST4.2x20 7
029 Lower Slide Tube Cover 1 059 Washer Ø6.5xØ16xT1.0 5
030 Upper Slide Tube Cover 1 060 Washer Ø8.4xØ19xT1.6 14

5
PARTS LIST
No. Description Qty No. Description Qty
061 Washer Ø10.5xØ20xT3.0 1 068 Front Stabilizer End Cap 2
062 Spring Washer Ø6.1xØ9.3xT1.6 6 069 Transport Wheel Ø50xØ8.5x21 2
063 Adjustable Foot Pedal 2 070 Hexagon Socket Button Head Bolt
M8x35 2
064 Pedal Strap 2 071 Lock Nut M8 6
065 Seat 260x320x52 1 072 Hexagon Socket Round Head
Bolt M8x30 4
066 Seat Roller Ø43.4x14.5 4 073 Cross Recessed Truss Head Bolt
M6x15 4
067 Spacer Ø12.0xØ8.2x11 4

6
HARDWARE PACK
STEP 1
(44) Carriage Bolt 2 PCS
(48) Cap Nut 2 PCS
(60) Washer 2 PCS
STEP 3
(28) Buffer 2 PCS
(49) Cross Recessed
Truss Head Bolt 2 PCS
(50) Hexagon Socket
Button Head Bolt 2 PCS
(60) Washer 2 PCS
STEP 5
(50) Hexagon Socket
Button Head
Bolt 4 PCS
(60) Washer 4 PCS
STEP 2
(28) Buffer 2 PCS
(49) Cross Recessed Truss Head Bolt 2 PCS
(50) Hexagon Socket Button Head Bolt 6 PCS
(60) Washer 6 PCS
S17
S13
Allen Wrench
with Phillips
Screwdriver
2 PCS
Double Open
End Wrench
1 PC

7
EXPLODED VIEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
24
25
26
27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
44
45
46
47
48
53
55
57
60
61
62
50
57
60
56
20
15
23 43
59
45
59
57
28
49
50
50
54
60
51
52
63
64
70
57
69 71 69
57
68
68
63
64
73
72
66
71
67
65
62
23
59
62
43
37
40 21
43 62 59 59 62 43
19
47
57
57
70
27 60
50
60 28 49
28
49
28 49
50
60
50
60
50
60
57
58
58
58
58
58
58
58
67
66
72
71
45
20
62
50 60
14
36 56

8
ASSEMBLY INSTRUCTIONS
STEP 1
Position the Front Stabilizer (9) in front of the Main Frame (11) and align bolt holes.
Attach the Front Stabilizer (9) onto the Main Frame (11) with two Carriage Bolts (44), two
Cap Nuts (48), and two Washers (60). Tighten cap nuts with the Double Open End
Wrench provided.
Hardware:
STEP 1
(44) Carriage Bolt 2 PCS
(48) Cap Nut 2 PCS
(60) Washer 2 PCS
48
60
9
11
44

9
STEP 2
A. Slide the Slide Tube (6) onto the Support Slide Tube (12) and align bolt holes. Attach
the Slide Tube (6) onto the Support Slide Tube (12) with four Hexagon Socket Button
Head Bolts (50) and four Washers (60). Tighten bolts with the Allen Wrench with
Phillips Screwdriver provided.
B. Attach the Slide Tube (6) onto the Support Slide Tube (12) with two Buffers (28), two
Cross Recessed Truss Head Bolts (49), two Hexagon Socket Button Head Bolts (50)
and two Washers (60). Tighten bolts with the Allen Wrench with Phillips Screwdriver
provided.
Hardware:
STEP 2
(28) Buffer 2 PCS
(49) Cross Recessed Truss Head Bolt 2 PCS
(50) Hexagon Socket Button Head Bolt 6 PCS
(60) Washer 6 PCS
50
60
12
6
A
50
60
50 60
49
28 49
B
11
28
12
6
60 50
6
12

10
STEP 3
A. Slide the Seat (65) to the Slide Tube (6).
B. Attach the Rear Stabilizer (5) to the rear end of the Slide Tube (6) with two
Buffers (28), two Cross Recessed Truss Head Bolts (49), two Hexagon Socket Button
Head Bolts (50) and two Washers (60). Tighten bolts with the Allen Wrench with
Phillips Screwdriver provided.
Hardware:
STEP 3
(28) Buffer 2 PCS
(49) Cross Recessed Truss Head Bolt 2 PCS
(50) Hexagon Socket Button Head Bolt 2 PCS
(60) Washer 2 PCS
NOTE: This side faces
downwards.
6
65
65
6
5
28
49
28
49
50
60
6
28
49
28 49
50
60
5
A
B

11
5
13
11
6
13
30
29
11
30
29
STEP 4
Hold the Slide Tube (6) with one hand and use the other hand to pull out the Safety Pin
(13) from the Main Frame (11) and Support Slide Tube (12).
STEP 4-1
Lower the Rear Stabilizer (5) until it makes contact with the floor. Lift the Main Frame (11)
and Slide Tube (6) to align the holes and insert the Safety Pin (13) into the hole on the
Main Frame (11).
11
13
6
13
11
6
12
12

12
STEP 5
Insert both Foot Pedal Axles (14) onto the Main Frame (11), and insert both Right and
Left Foot Pedals (1, 2) onto the Foot Pedal Axles (14). Tighten both Right and Left Foot
Pedals (1, 2) in place with four Hexagon Socket Button Head Bolts (50) and four
Washers (60) by using the Allen Wrench with Phillips Screwdrivers provided.
Hardware:
STEP 5
(50) Hexagon Socket Button Head Bolt 4 PCS
(60) Washer 4 PCS
14
14
50
60
1
50
60
11
2
50
60
50
60
14
14
50
60
1
50
60
11
2
50
60
50
60

13
STEP 6
A. Lift up on the CLIP and gently pulling the Computer Console (35) out. BE CAREFUL
when pulling the Computer Console (35) out. There are three wires attached to the
backside.
B. Using the Allen Wrench with Phillips Screwdriver to remove the screw from the
Computer Console (35) to open the battery cover. Place four size AA batteries into
the battery housing with the positive and negative poles as labeled.
Reattach the battery cover and secure with the screw that was removed. Replace the
Computer Console (35) back into the rower. Make sure the three wires are still
connected before replacing the Computer Console (35). If any one of them is not
connected, the Computer Console (35) will not function correctly.
Make sure that all parts are properly tightened before using the
equipment.
CLIP
A 35
35
31 32
B

14
13
11
6
11
6
13
12
11
6
13
12
13
6
5
STORAGE
To store the Rower:
Hold the Slide Tube (6) with one hand and use the other hand to pull out the Safety Pin
(13) from the Main Frame (11).
Lift the Slide Tube (6) up until the Main Frame (11) and Support Slide Tube (12) to align
the holes and insert the Safety Pin (13) into the hole on the Main Frame (11).
To use the Rower:
Hold the Slide Tube (6) with one hand and use the other hand to pull out the Safety Pin
(13) from the Main Frame (11) and Support Slide Tube (12).
Lower the Rear Stabilizer (5) until it makes contact with the floor. Lift the Main Frame (11)
and Slide Tube (6) to align the holes and insert the Safety Pin (13) into the hole on the
Main Frame (11).

15
MAINTENANCE
The rower can be cleaned with a soft damp cloth. Do not use abrasives or solvents on
plastic parts. Please wipe your perspiration off the rower after each use. Be careful not to
get excessive moisture on the computer display panel as this might cause an electrical
hazard or it may cause the electronics to fail.
Keep the computer console and the rower, out of direct sunlight to prevent screen damage.
The rower is sturdy and balanced when in storage mode but do NOT hang articles of
clothing on it. The clothing can unbalance the rower and it could fall over.
Do NOT allow children or pets near the rower when in storage mode.
Inspect all assembly bolts, nuts, screws, and pedals on the machine for proper tightness
every week.
MOVING THE ROWER
Hold the Rear Stabilizer and lift the rower until the Transport Wheels make contact with the
floor. Push or pull the unit to the desired location, then gently lower the Rear Stabilizer to
the ground.
Rear Stabilizer
Transport Wheel
Rear Stabilizer
Transport Wheel

16
OPERATING THE COMPUTER
USING THE COMPUTER CONSOLE
Power On: The computer console will turn on when the user starts rowing or presses a
button on the computer console.
Power Off: The computer console will automatically turn off after 20 minutes of inactivity.
Reset: Press and hold the STOP button for 3 seconds to reset the computer console.
Pause: Press the START button during a workout.
Start Workout: Press the START button on the computer console to begin tracking your
workout.
End Workout: Press the STOP button to end a workout and show the workout results.
WORKOUT DISPLAY
STROKES: Will track the total number of strokes/pulls during the workout, up to a total of
9999.
CAL: Will track the number of calories burned during the workout, up to a value of 999.
This Calorie burn is only an estimated value base on an average user.
TIME: Will track the total workout time, up to a maximum value of 99:59 minutes.
SPM: Will display the average number of strokes you are pulling in a minute based on the
current workout pace.
This display will shift between SPM and METERS every 4 seconds.
See the indicator arrow for the value currently being displayed.
METERS: Will track your distance in meters, up to a maximum value of 9999 meters. The
Computer console will change to KILOMETERS (KM) when 9999 meters is reached.
This display will shift between SPM and METERS every 4 seconds.
See the indicator arrow for the value currently being displayed.

17
Tension Control Knob
SPLIT: Will display the average time it takes to travel 500 meters based on the current
workout pace.
WATTS: Will display the current workout effort in the form of Watts.
The Watts value is dependent on the length of the pull, the pace of the workout, and the
resistance level.
The resistance level control knob is wired to the computer console to track the effort of the
workout based on the resistance level set on the control knob.
At the end of the workout, this section will show the MAX watt values reached during the
workout.
SETTING WORKOUT GOALS
1. Press the GOALS button before starting a workout to set a METERS, TIME,
CALORIES, or STROKES GOAL.
2. Press the GOALS button until the desired GOAL option is flashing.
3. Use the UP and DOWN buttons to adjust the GOAL value.
4. Press the ENTER button to confirm the GOAL value.
5. Press the START button to begin the workout.
6. The computer console will beep 3 times when the GOAL is achieved.
END WORKOUT
End the workout by pressing the STOP button. The workout results will stay on the display
for reviewing.
The TOTAL STROKES, TOTAL TIME, TOTAL CALORIES, AVERAGE SPM,
TOTAL METER/KILOMETERS, AVERAGE SPLIT TIME, and the MAX WATT level reached.
Press the STOP button a second time to return to the main screen.
ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the tension, turn the tension control knob in a clockwise direction.
To decrease the tension, turn the tension control knob in a counterclockwise direction.

18
Adjustable Leveler
Adjusting the Adjustable Leveler
Turn the adjustable leveler on the front stabilizer as needed to level the rower.
Adjusting the Adjustable Foot Pedal
First pull the adjustable foot pedal up and then slide the adjustable foot pedal up or down
direction to the suitable position. Lock the adjustable foot pedal in place by pushing down
the adjustable foot pedal to the suitable level dots on the foot pedal.

19
TROUBLESHOOTING
PROBLEM: The rower wobbles when in use.
SOLUTION: Turn the adjustable level on the front stabilizer as needed to level the rower.
PROBLEM: There is no display on the computer console.
SOLUTION: Remove the computer console and verify the wires that come from the
computer console are properly connected to the wires that come from the main frame.
SOLUTION: Check that the batteries are correctly positioned and battery springs are in
proper contact with batteries.
SOLUTION: The batteries in the computer console may be dead. Replace the dead
batteries with new batteries. Do NOT mix old and new batteries.

PROBLEM: The rower makes a noise when in use.
SOLUTION: The bolts may be loose on the equipment. Please inspect all of the nuts,
bolts, screws and tighten any loose Hardware.

PROBLEM: The computer console is on but it is not tracking my workout. The strokes are
not counting up.
SOLUTION: Press the START button before starting your workout. The computer console
does NOT auto start when user starts pulling on the strap. This is to allow you to choose
setting up a workout goal option before starting the workout.
SOLUTION: Make sure the 3 computer console wires on the back of the computer console
are connected.
If the above troubleshooting section does not fix the problem, discontinue use the
rower.
PLEASE CONTACT YOUR LOCAL DEALER FOR
SUPPORT.