Lifetime 60030 User manual

1
MODEL N° 60030
OWNER’S MANUAL
Keep this Identification Number in case you must contact our Customer Service Department.

2
**For customers outside the U.S. or Canada, please contact the store for assistance.**
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 [phone]
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call, or visit our Web site for Saturday hours**
Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use, and supervision are essential to reduce the risk of accident or
injury. A high probability of serious injury exists if this system is not installed, maintained, and/or operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE AND WILL VOID WARRANTY.
t5XPDBQBCMFBEVMUTBSFSFDPNNFOEFEGPSBTTFNCMZ
t'PMMPXBOZBOEBMMXBSOJOHTBOEDBVUJPOTDBSFGVMMZ
t"TTFNCMFPOMFWFMHSPVOE
t$IFDLBMMOVUTBOETDSFXTGPSUJHIUOFTTCFGPSFBOEEVSJOHUIFVTBHFTFBTPO
SAFETY INSTRUCTIONS
REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM
LIFETIME’S PROMISE TO YOU:
We invite you to read our privacy policy at www.lifetime.com
REGISTER today!
At Lifetime, we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input
is valuable to us.
t:PVDBOBMTPPQUJOUPSFDFJWFOFXQSPEVDUOPUJmDBUJPOTPSQSPNPUJPOT
t*OUIFVOMJLFMZFWFOUPGBQSPEVDUSFDBMMPSTBGFUZNPEJmDBUJPOZPVSSFHJTUSBUJPOQSPWJEFTUIFJOGPSNBUJPOXFOFFEUPOPUJGZZPV
directly.
t3FHJTUSBUJPOJTGBTUFBTZBOEDPNQMFUFMZWPMVOUBSZ
Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or provide your
personal data to other third parties, or allow them to use your personal data for their own purposes.
04/1/2012
INSTRUCTION #1066877 D

3
TOOLS REQUIRED FOR ASSEMBLY
*TWO ADULTS REQUIRED TO
COMPLETE ASSEMBLY*
BEFORE BEGINNING ASSEMBLY
Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service
Department.
The plastic pieces of your table may become damaged by over tightening the screws. If you choose
to use a power screwdriver, we strongly recommend the use of a low-powered power screwdriver or a
drill that has an adjustable clutch that is set to a low-torque setting. If neither is available, use a hand
screwdriver or socket wrench.

Safety Glasses
(1) (1 pair for each person)
Electric Drill
!

4
This area is located at the top, left-hand
corner of the page and indicates which tools
and hardware are needed to complete the
assembly steps on a page.
This area is located at the top, right-hand
corner of the page and shows an image of the
product with shaded parts indicating which
section is being assembled.
SEC
#
Note:
!
Refer to the following areas throughout the instructions
to assist in the assembly process:
This area is usually located in the bottom,
left-hand corner of a step and indicates that
special attention is needed to perform a
particular part of a step.
These areas are usually located in the bottom,
right-hand corner of a step and indicate that
damage to the product or serious injury may
occur if the caution or warning is not heeded.
Throughout the Parts & Hardware List, Part
& Hardware Identifiers, and instructions
are three-letter IDs. These IDs are below
the images of the parts and hardware to
help you locate and identify the parts and
hardware during assembly. These IDs are not
necessarily on the parts themselves.
WARNING
ASSEMBLY GUIDE
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
CAUTION
ADZ (x10)
1/4” x 5/8” Pan-Head Screw

5
ID DESCRIPTION QTY
BWM Table Top Assembly 1
BWN Bench Assembly 2
BWO W-Frame Leg Assembly 2
BWP W-Frame Leg Brace Assembly 2
W-FRAME TABLE HARDWARE [BWL]
)BSEXBSFTIPXOBUBDUVBMTJ[F6OMFTTOPUFEPUIFSXJTF
PARTS & HARDWARE IDENTIFIER
PARTS & HARDWARE LIST
ID DESCRIPTION QTY
BWL W-FRAME TABLE HARDWARE
BWI Sliding End Cap 8
BWH 6.3 mm x 25 mm Hex-Head Screw 8
BWG M6 x 1 x 12 mm Hex Bolt 4
AON M6 x 1 Nylock Cap Nut 4
BWG (x4)
M6 x 1 x 12mm Hex Bolt
AON (x4)
M6 x 1 Nylock Cap Nut
BWH (x8)
6.3mm x 25mm Hex-Head Screw
BWI (x8)
Sliding End Cap
1BSUTTIPXOBUPGBDUVBMTJ[F
BWM (x1)
Table Top Assembly
BWN (x2)
Bench Assembly
BWO (x2)
W-Frame Leg Assembly BWP (x2)
W-Frame Leg Brace Assembly

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
6
SEC
SEC
1.1
1
PICNIC TABLE ASSEMBLY
BWM
Remove all screws connecting the
Table Top channel to the Table Top
Table Top Channel
Lay the Table Top Assembly (BWM) upside down on the ground. Remove the five (5) screws connecting one of the
Table Top channels to the Table Top, and remove the channel from the Table Top. Save Screws for later in the
assembly.
NO HARDWARE REQUIRED FOR THIS PAGE
SEC
1.2 If the Locking Strap is not already attached to the W-Frame Leg Brace Assembly (BWP), slide a Locking Strap over the
tube of the Leg Brace as shown. Ensure the Locking Strap is oriented with the metal ring facing downward as shown.
BWP
Locking Strap

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
7
SEC
SEC
1.3
SEC
1.3
1
2 ADULTS REQUIRED FOR THIS STEP
Insert a W-Frame Leg Assembly (BWO) and a W-Frame Leg Brace Assembly (BWP) into the two large holes along the Table
Top channel that is still connected to the Table Top as shown. Ensure you orient the Brace in the direction shown
(the locking mechanism must be visible). Repeat step 1.2 - 1.3 for the second W-Frame Leg Assembly and W-Frame Leg Brace
Assembly.
While another adult helps to hold the Assemblies in position, place the holes in the second Table Top channel
over the tubes of the Table Legs and Table Leg Braces as shown.
NO HARDWARE REQUIRED FOR THIS PAGE
SEC
1.3
SEC
1.4
BWO
Table Top Channel
Table Top Channel

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
8
SEC
1
2 ADULTS REQUIRED FOR THIS STEP
SEC
1.5 Set the Table Top Channel back in place. While another adult holds the Legs, reinsert the five (5) screws you
removed in step 1.1 into the holes of the Table Top Channel to secure it in place. Do not overtighten.
Reinsert all five Screws
removed in step 1.1
BWI
BWI
SEC
1.3 Lay the Table Legs and Table Leg Braces down flat on the Table Top. Place a Sliding End Cap (BWI) on the ends of
the tube on a Table Leg as shown.
SEC
1.6
BWH
BWH
BWH (x5)
All removed in Step 1.1
BWI (x2)

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
9
SEC
1
BWI (x6)
SEC
1.7 Place a Bench Assembly (BWN) underneath one of the Legs and slide the Sliding End Caps under the glide rails of
the Bench Assembly as shown.
Glide Rail
SEC
1.3 Attach two (2) Sliding End Caps (BWI) to the tube on the other Table Leg, and lift the Bench Assembly upward until
the Sliding End Caps rest inside the underside of the Bench. Position the Bench so all four Sliding End Caps are
under the glide rails. Repeat steps 1.6 - 1.8 for the second Bench Assembly.
SEC
1.8
BWN
2 ADULTS REQUIRED FOR THESE STEPS

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE
10
SEC
1
SEC
1.3 Lift the Legs upright and, while another adult holes the Table Legs in place, rotate the diagonal supports of a
Table Leg Brace until the locking pin snaps into the notches located at the ends of the diagonal supports as
illustrated. Connect the other ends of the supports to the Table Leg using two (2) M6 x 1 x 12mm Hex Bolts (BWG) and
two (2) M6 x 1 Nylock Cap Nuts (AON). Repeat this step for the other Table Leg Brace.
Locking Pin
Diagonal Supports
SEC
1.9
BWG
BWG
AON
AON
10mm (x2)
BWG (x4)
AON (x4)
SEC
1.10 While another adult holds the Table Legs upright, insert four (4) 6.3mm x 1.8 x 25mm Hex-Head Screws (BWH) through
the holes in the Bench Channels and into the Bench as shown to keep the Sliding End Caps under the Glide
Rails. Do not overtighten. Repeat this step for the other Bench.
BWH
BWH
2 ADULTS REQUIRED FOR THESE STEPS
BWH (x8)