Lightolier IS-CL User manual

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2010 Philips Group •
Lighting Systems IS_CL
Page 1 of 2 Instruction Sheet for Assembly and Installation of Covelite
C1010 ~ 59.31233.00
• READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
• KEEP THESE INSTRUCTIONS FOR MAINTENANCE REFERENCE.
• THIS FIXTURE IS INTENDED TO BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE AND LOCAL REGULATIONS.
• TO ASSURE FULL COMPLIANCE WITH LOCAL CODES AND REGULATIONS, CHECK WITH THE LOCAL ELECTRICAL INSPECTOR
BEFORE INSTALLATION.
• TO PREVENT ELECTRICAL SHOCK, TURN OFF ELECTRICITY AT ELECTRICAL PANEL BEFORE PROCEEDING.
• DO NOT INSTALL THIS SYSTEM IN A WET OR DAMP LOCATION.
• DO NOT ENERGIZE ANYTHING OTHER THAN THE FIXTURES IN THE SYSTEM.
• CONTRACTOR IS RESPONSIBLE FOR ADEQUATELY REINFORCING THE MOUNTING LOCATIONS OF THIS FIXTURE.
These instructions review how to install CoveLite xtures. CoveLite can be installed as individual units or connected together to create
continuous runs. If the units are mounted in a radial pattern there must be protection for exposed conductors and at connections.
MATERIALS REQUIRED
• Mounting screws appropriate for the mounting surface
• Appropriate screwdriver(s)
• One 1/2” (for 7/8” hole) knock-out seal for each end of row
• Wire nuts
• Flexible conduit connector for each power connection
• Flexible conduit required for corners and if xture is mounted in a radial pattern.
The xtures come in different lengths and can be mounted to a horizontal or vertical surface in two different positions. Figure 1 depicts the
different mounting positions and Figure 2 shows the actual length for nominal xture lengths.
Nominal
Fixture
Length
Actual Fixture Length
1 Light T5 2 Light T5 1 Light T8 2 Light T8
2' 1'-11" 1'-11" 2' 2'
3' 2'-10 1/2" 2'-10 1/2" 3' 3'
4' 3'-10 1/2" 3'-10 1/2" 4' 4'
6' 5'-9" 5'-9" 6' 6'
8' 7'-9" 7'-9" 8' 8'
Horizontal Mounting, Position A Vertical Mounting, Position A
Figure 2Figure 1
Figure 3A Figure 3B
STEP 1: Determine the correct mounting position and mount the rst xture using appropriate fasteners through the slots in the housing
(Figure 3A). For 2 light T8 xtures the screw is hole is located on the end of the xture (Figure 3B).
A
H izontal u ting Pos t on A Vert cal Mounting, Posi on A
A
BB
C
INSTALLATION STEPS

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2010 Philips Group •
Lighting Systems IS_CL
Page 2 of 2 Instruction Sheet for Assembly and Installation of Covelite
C1010 ~ 59.31233.00
Outside Corner Inside Corner
INSTALLATION STEPS
STEP 2: Install the power to the xture leads using wire nuts (by others) (Figure 4). Power feed connections can also be made through the
back of the xture by removing the knock-out (not shown). If the rst xture is not the location where the power is being supplied, cap all
wires and tuck them into the xture cavity. At the end of the run cap the hole using a ½” knock-out plug (by others).
STEP 3: For each additional xture in the run, make the appropriate wire connections and tuck the wires and connections into the xture
cavity. Slide the xtures together and secure using appropriate fasteners through the slots in the housing (Figure 5). For 2 light T8 xtures
align the tabs with the slots from the previous xture and slide together. Secure the new xture with an appropriate screw in the mounting
tab at the opposite end.
At a corner power connections can be made using ex conduit and connectors (Figure 6).
i nta i
Figure 4
Figure 5
Figure 6