Lightolier F7000-19 User manual

Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems F7000-19
1BHFPG '4FSJFT-JHIU54PMJE
&
Armstrong®5FDI;POFÜ$PNQBUJCMF
Features
1. Housing: Single piece of high purity extruded aluminum, a portion from
recycled material.
2. Housing End: Die-cast aluminum, welded in place.
3. End Cap: Die-cast aluminum. Encloses the suspension cable and power feed
cord for the end of the run.
4. Lamps: F28T5 or F54T5HO as specified. By others. Installed fromthe ceiling
side of the luminaire.
5. Ballast: Electronic. Meets ANSI starting, end-of-life protection and sound
rating specifications. Low THD. Maximumballast size is 1.2” (3.05cm) wide by
0.625” (1.59cm) high.
6. Reflector: Die-formed specular aluminum.
Electrical
Connections: Pre-wired with 18 gauge wires and polarized cannon plug con-
nectors for simultaneous mechanical/electrical connection.
Emergency Battery Pack: 90 minute operation, 700 lumens for 54W and 520
lumens for 28W.
Power Feeds: Standard 18/3 power feed is rated for 10 amps. X4 power feed
is 18/4 and is rated for 7 amps. Observe amperage limitations and provide addi-
tional Intermediate Power Cables, as required. When providing an additional
power feed, the through wiring fromthe previous module must be disconnected
fromthe cannon plug and capped.
Mounting
Cable suspension is on 48” (121.92cm) and 96” (243.94cm) centers and consists of
a 4 1/2” (11.43cm) diameter canopy finished white enamel and a 1/16” (0.16cm)
diameter stainless steel aircraft cable adjustable up to 36” (91.44cm).
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order one MODULE.
2. Order one POWER FEED END SET.
Continuous Rows:
1. Order the appropriate number of MODULES for the complete run.
2. Order one POWER FEED END SET.
3. Order one INTERMEDIATE CABLE SET per MODULE minus one.
4. For runs that exceed amperage limits, order the appropriate number of
CABLE/CORD SETs.
Finish
Powder-coated, baked enamel, white or aluminum, as specified.
Ordering Information
Complete Ordering Instructions below.
6.75” (17.15cm)
1.63”
(4.14cm)
F7
Family Series
5
Type Lamps Color Wattage Voltage Length Options
1 1
5= Curved 1= Solid 1= 1 LampAL = Aluminum
WH = White
1= 28W
2= 54W
4= 28W EM
6= 54W EM
1= 120v
2= 277v
4= 4’ (121.92cm)
8= 8’ (243.84cm)
X4 = 4 Through
Wires
X5 = 5 Through
Wires
5
4
61
Factory installed ballast disconnect allows the ballast to be disconnected fromand
reconnected to incoming power under load without turning the entire circuit off.

Job Information Type:
"JSQPSU3PBE'BMM3JWFS."tt'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems F7000-19
1BHFPG '4FSJFT-JHIU54PMJE
&
CANDLEPOWER
ZONE 0 22 45 67 90
DEG.
CANDELAS
90 0 3 11 17 20
95 18 266 304 323 308
105 93 474 880 1013 1047
115 188 508 996 1363 1450
125 288 559 912 1222 1360
135 382 594 885 1098 1183
145 464 612 828 990 1055
155 528 614 755 856 900
165 570 607 672 720 742
175 591 593 600 605 611
180 590 590 590 590 590
Performance
CANDLEPOWER CURVE
1400
1050
700
350
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
REPORT NO.: ITL54693.IES
LAMPS: 1-F54T5
LUMENS: 5000 each
EFFICIENCY: 90.1%
CAT. NO: F7511WH214
DISTRIBUTION
Zone Lumens % Lamp %Luminaire
0 - 90 0 0.0 0.0
90 - 180 4503 90.1 100.0
0 - 180 4503 90.1 100.0
Mounting Accessories
Power Feed End Set:
F7EC36WH = White
F7EC36AL = Aluminum
F7EC36WHX4 = White 4 Wire
F7EC36ALX4 = Aluminum4 Wire
F7EC36WHX5 = White 5 Wire
F7EC36ALX5 = Aluminum5 Wire
Intermediate Power Cable
F7CC36 = 3 Wire
F7CC36X4 = 4 Wire
Intermediate Cable Set
F7C36
80% 70% 50%
50 30 10 50 30 10 50 30 10
0 868686 7373 73 505050
1 747168 6461 59 444241
2 656056 5652 48 383634
3 575146 4944 40 343128
4 504439 4338 34 302624
5 443833 3833 29 262320
6 393328 3428 24 232017
7 352924 3025 21 211715
8 322521 2722 18 191513
9 292218 2519 16 171411
10 26 20 16 22 17 14 16 12 10
20% FLOOR CAVITY REFLECTANCE
COEFFICIENTS OF UTILIZATION
% EFFECTIVE CEILING CAVITY REFLECTANCE
WALL REFLECTANCE
ROOM CAVITY RATIO
“X” Joiner Block
F7XWH = White
F7XAL = Aluminum
12" (30.48cm)
“T” Joiner Block
F7TWH = White
F7TAL = Aluminum
6" (15.24cm)
12" (30.48cm)
“L” Joiner Block
F7LWH = White
F7LAL = Aluminum
6"
(15.24cm)
Fixture Lengths & Mounting Reflected (Plan View)
4'-0" (121.92cm)
8'-0" (243.84cm)
4'-0"
(121.92cm)
3/4" (1.91cm)
1-1/2"
(3.81cm)
3/8" (0.95cm)
END OF ROW DETAIL
GAP BETWEEN FIXTURES
JOINING DETAIL
4'-3" (129.54cm)
8'-0" (243.84cm)
4'-0" (121.92cm)
12'-3" (373.38cm)
8'-0" (243.84cm)
8'-0" (243.84cm)
16'-3" (495.30cm)
8'-3" (251.46cm)
8'-0" (243.84cm)
20'-3" (617.22cm)
8'-0" (243.84cm)
Inline Joiner Block
F7ILWH = White 1’ (30.48cm)
F7ILAL = Aluminum1’ (30.48cm)
F7IL2WH = White 2’ (60.96cm)
F7IL2AL = Aluminum2’(60.96cm)
F7IL4WH = White 4’ (121.92cm)
F7IL4AL = Aluminum4’ (121.92cm)
F7IL8WH = White 8’ (243.84cm)
F7IL8AL = Aluminum8’ (243.84cm)
12" (30.48cm)