Suzhou Lily Tech. CO., Ltd.
Page 4, Total 7 Pages
Cool mode【t0 = C】
If Room temp. ≥ Set temp. +【t1】, and Temp. Output has stopped for【t2】, then Temp. Output will be energized.
If Room temp. ≤ Set temp., then Temp. Output will be de-energized.
Over hot protection
If Room temp. ≥ Set temp. +【t4】, then output R1 will be energized.
If Room temp. ≤ Set temp. +【t4】-【t5】, then output R1 will be de-energized.
This protection function is only effective in heat mode.
If【t4】=【t5】= 0.0, disable the protection function.
Humidity control
Humidify mode 【h0 = H】
If Room humidity ≤ Set humidity (HP) -【h1】, and Humi. Output (R2) has stopped for【h2】, then Humi. Output will be
energized.
If Room humidity ≥ Set humidity, then Humi. Output will be de-energized.
Dehumidify mode【h0 = P】
If Room humidity ≥ Set humidity +【h1】, and Humi. Output has stopped for【h2】, then Humi. Output will be energized.
If Room humidity ≤ Set humidity, then Humi. Output will be de-energized.
Over wet protection
If Room humidity ≥ Set humidity +【h4】, then output R1 will be energized.
If Room humidity ≤ Set humidity +【h4】-【h5】, then output R1 will be de-energized.
This protection function is only effective in humidify mode.
If【h4】=【h5】= 0.0, disable the protection function.
Timer output R4 and R5
R4 and R5 are controlled by parameter【u0】,【u1】and【u2】.
R4 and R5 will be energized for【u1】time alternatively. A period includes an R4 energized and an R5 energized.
There is a counter counting the times of the period. Every time after the power supplied, the counting value is reset to zero.
keeping 【S】and【▼】depressed simultaneously will show the counting value for 3 seconds.
If 【u2】> 0, when the counting value reaches 【u2】, R4 and R5 will stop energized, and display and will blink.
If 【u2】is set to zero,R4 and R5 will never stop energized.
Forced energized manually:
Keeping【▲】depressed for 2 seconds makes R5 being energized, until the key is released.
Keeping【▼】depressed for 2 seconds makes R4 being energized, until the key is released.
R4 and R5 could be used for incubator egg tray control.
Alarm
High temp. alarm: if Room temp. ≥ Set temp. (TP) +【t6】, display “tHi”. If【t6】= 0.0, the function disable.
Low temp. alarm: if Room temp. ≤ Set temp. -【t7】, display “tLo”. If【t7】= 0.0, the function disable.
High humidity alarm: if Room humidity ≥ Set humidity (HP) +【h6】, display “hH”. If【h6】= 0.0, the function disable.
Low humidity alarm: if Room humidity ≤ Set humidity -【h7】, display “hL”. If【h7】= 0.0, the function disable.
Sensor
The Room temp. can be calibrated. If Room temp. is 0.2℃lower than real temp., set 【t3】= 0.2.
The Room humidity can be calibrated. If Room humidity is 2%RH higher than real, set 【h3】= -2.
When sensor fails, the Temp. and Humi. Output (R3, R2) will not be energized, and “E01” will display.
Note: do not plug in/off the sensor when power supplied.
