Linak ACTUATOR LA36 Instruction manual

Actuator LA36/LA37
Endstop signals and relative positioning - Single hall
Connection diagram
LINAK.COM/TECHLINE

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-539-A .LINAK A/S reserves the right to make technical alterations
Connection diagram
9
2019 © LINAK A/S
Endstop signals and relative positioning - Single hall
36XXXX+2KXXXXXX
37XXXX+2KXXXXXX
BROWN
BLUE
YELLOW*
GREEN*
RED
VIOLET
BLACK
+
-
*YELLOW/GREEN: Endstop signals out are NOT potential free (see specifications on next page)
Tip: If you wish to use the endstop signals, you will have to keep power on the brown, blue,
red and black wires, otherwise the signal will be lost.

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-539-A .LINAK A/S reserves the right to make technical alterations
I/O Specifications
9
2019 © LINAK A/S
Endstop signals and relative positioning - Single hall
Input/Output Specification Comments
Description The actuator can be equipped with Single hall that
gives a relative positioning feedback signal when the
actuator moves.
See connection diagram, figure above
Brown 12, 24 or 36* VDC (+/-)
*Only available on LA36
12V ± 20%
24V ±10%
36V ±10%
Under normal conditions:
12V, max. 26A depending on load
24V, max. 13A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12-24VDC Current consumption:
Max. 40mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Endstop signal out Output voltage min. VIN - 2V
Source current max. 100mA
NOT potential free
Yellow Endstop signal in
Violet Single Hall output (PNP)
Movement per Single Hall pulse:
LA371C: Actuator = 0.1372 mm per count
Frequency:
Frequency is 14-26 Hz on Single Hall output depending
on load.
Overvoltage on the motor can result in shorter pulses.
Output voltage min. VIN - 2V
Max. current output: 12mA
Max. 680nF
N.B. For more precise measure-
ments, please contact LINAK A/S.
Low frequency with a high load.
Higher frequency with no load.
Input: Single hall output:
White Not to be connected

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-539-A .LINAK A/S reserves the right to make technical alterations
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and
changes without prior notice.Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability
of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed
in its catalogues or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.