Linak TWINDRIVE HB12 User manual

Copyright©LINAK 2010.08 MA M9-02-275-B
TWINDRIVE®RF based Systems
without Memory
www.linak.com
Functional description
Transmitter HB12 + HB22:
Up – down head motor
Up – down foot motor
Simultaneous up/down
This is only an additional guideline
Should you have further questions, please contact the
bed manufacturer
Is only valid for the motor part (TWINDRIVE®system).
Child lock - only on HB22
Enable/Disable Child lock
1. Remove 1 battery and wait 15 seconds
2. Press both buttons on second row and keep the keys pressed
3. Mount the battery at the same time (the keys are pressed)
4. The child lock function is now enabled
2. 3.
Unlock of Child lock
Press up and down keys of the 2nd row at the same time for one
sec.
When the blue LED turns on the handset is unlocked.
The handset is not unlocked If the keys are not released again
before the blue led turns off.
Lock
If no keys are pressed for 10 seconds, the handset will lock again.
Factory settings (disabled childlock)
Dismount 1 battery and wait 15 seconds. Mount the battery
and the HB is back to factory setting.

Congratulations on your new elevation bed!
An actuator is mounted in the bed. This is the electronic unit,
which moves the bed, when you press the handset. The actuator
is a LINAK product. LINAK is the world’s leading manufacturer of
actuator systems.
A LINAK actuator is reliable and noiseless. It provides a high and
constant force, and it leaves more space under the bed than any
other actuator.
The actuator has been constructed with full focus on security.
At the same time, it has the lowest power consumption in the
market.
In short: A LINAK actuator is a quality product, which is built to
ensure full functionality several years ahead. In this user manual,
you can fi
nd advice and information.
For further information, please read our user manuals on our
website http://www.linak.com/products/Dual-Actuators.aspx.
We recommend that you read the user manual thoroughly
through before use, so that you will have optimum pleasure with
the bed and the LINAK actuator many years ahead.
Have a good time!
Start-up:
The TD can accept commands from up to 2 RF handsets.
From the factory, the TD cannot recognize any RF handsets at
all. Therefore, the end user/bed manufacturer must match it to
the RF handset before they can control the TD operation.
Conditions which must be fulfilled prior to activating the
learning mode:
TD1:
1. Connect the TD1 to the mains
2. Wait 20 sec.
3. Activate the reset key on the TD1 by using a fingertip, keep
the button pressed (1 - 2 sec.). Push at the same time on a
button at the HB. HB is now paired to the TD. System is now
(setup) ready to be used. (This learning mode also works via
battery pack).
TD3
TD1
TD3:
1. Connect the TD3 to the mains
2. Wait 20 sec.
3. Activate the reset key and keep it pressed until the motor stops.
4. Release the reset key
5. Activate the reset key on the TD3 by using a pen, keep the
button pressed (1 - 2 sec.). Push at the same time on a button
at the HB. HB is now paired to the TD. System is now (setup)
ready to be used. (This learning mode also works via battery
pack).

Congratulations on your new elevation bed!
An actuator is mounted in the bed. This is the electronic unit,
which moves the bed, when you press the handset. The actuator
is a LINAK product. LINAK is the world’s leading manufacturer of
actuator systems.
A LINAK actuator is reliable and noiseless. It provides a high and
constant force, and it leaves more space under the bed than any
other actuator.
The actuator has been constructed with full focus on security.
At the same time, it has the lowest power consumption in the
market.
In short: A LINAK actuator is a quality product, which is built to
ensure full functionality several years ahead. In this user manual,
you can fi
nd advice and information.
For further information, please read our user manuals on our
website http://www.linak.com/products/Dual-Actuators.aspx.
We recommend that you read the user manual thoroughly
through before use, so that you will have optimum pleasure with
the bed and the LINAK actuator many years ahead.
Have a good time!
Start-up:
The TD can accept commands from up to 2 RF handsets.
From the factory, the TD cannot recognize any RF handsets at
all. Therefore, the end user/bed manufacturer must match it to
the RF handset before they can control the TD operation.
Conditions which must be fulfilled prior to activating the
learning mode:
TD1:
1. Connect the TD1 to the mains
2. Wait 20 sec.
3. Activate the reset key on the TD1 by using a fingertip, keep
the button pressed (1 - 2 sec.). Push at the same time on a
button at the HB. HB is now paired to the TD. System is now
(setup) ready to be used. (This learning mode also works via
battery pack).
TD3
TD1
TD3:
1. Connect the TD3 to the mains
2. Wait 20 sec.
3. Activate the reset key and keep it pressed until the motor stops.
4. Release the reset key
5. Activate the reset key on the TD3 by using a pen, keep the
button pressed (1 - 2 sec.). Push at the same time on a button
at the HB. HB is now paired to the TD. System is now (setup)
ready to be used. (This learning mode also works via battery
pack).

Congratulations on your new elevation bed!
An actuator is mounted in the bed. This is the electronic unit,
which moves the bed, when you press the handset. The actuator
is a LINAK product. LINAK is the world’s leading manufacturer of
actuator systems.
A LINAK actuator is reliable and noiseless. It provides a high and
constant force, and it leaves more space under the bed than any
other actuator.
The actuator has been constructed with full focus on security.
At the same time, it has the lowest power consumption in the
market.
In short: A LINAK actuator is a quality product, which is built to
ensure full functionality several years ahead. In this user manual,
you can fi
nd advice and information.
For further information, please read our user manuals on our
website http://www.linak.com/products/Dual-Actuators.aspx.
We recommend that you read the user manual thoroughly
through before use, so that you will have optimum pleasure with
the bed and the LINAK actuator many years ahead.
Have a good time!
Start-up:
The TD can accept commands from up to 2 RF handsets.
From the factory, the TD cannot recognize any RF handsets at
all. Therefore, the end user/bed manufacturer must match it to
the RF handset before they can control the TD operation.
Conditions which must be fulfilled prior to activating the
learning mode:
TD1:
1. Connect the TD1 to the mains
2. Wait 20 sec.
3. Activate the reset key on the TD1 by using a fingertip, keep
the button pressed (1 - 2 sec.). Push at the same time on a
button at the HB. HB is now paired to the TD. System is now
(setup) ready to be used. (This learning mode also works via
battery pack).
TD3
TD1
TD3:
1. Connect the TD3 to the mains
2. Wait 20 sec.
3. Activate the reset key and keep it pressed until the motor stops.
4. Release the reset key
5. Activate the reset key on the TD3 by using a pen, keep the
button pressed (1 - 2 sec.). Push at the same time on a button
at the HB. HB is now paired to the TD. System is now (setup)
ready to be used. (This learning mode also works via battery
pack).

Copyright©LINAK 2010.08 MA M9-02-275-B
TWINDRIVE®RF based Systems
without Memory
www.linak.com
Functional description
Transmitter HB12 + HB22:
Up – down head motor
Up – down foot motor
Simultaneous up/down
This is only an additional guideline
Should you have further questions, please contact the
bed manufacturer
Is only valid for the motor part (TWINDRIVE®system).
Child lock - only on HB22
Enable/Disable Child lock
1. Remove 1 battery and wait 15 seconds
2. Press both buttons on second row and keep the keys pressed
3. Mount the battery at the same time (the keys are pressed)
4. The child lock function is now enabled
2. 3.
Unlock of Child lock
Press up and down keys of the 2nd row at the same time for one
sec.
When the blue LED turns on the handset is unlocked.
The handset is not unlocked If the keys are not released again
before the blue led turns off.
Lock
If no keys are pressed for 10 seconds, the handset will lock again.
Factory settings (disabled childlock)
Dismount 1 battery and wait 15 seconds. Mount the battery
and the HB is back to factory setting.

Copyright©LINAK 2010.08 MA M9-02-275-B
TWINDRIVE®RF based Systems
without Memory
www.linak.com
Functional description
Transmitter HB12 + HB22:
Up – down head motor
Up – down foot motor
Simultaneous up/down
This is only an additional guideline
Should you have further questions, please contact the
bed manufacturer
Is only valid for the motor part (TWINDRIVE®system).
Child lock - only on HB22
Enable/Disable Child lock
1. Remove 1 battery and wait 15 seconds
2. Press both buttons on second row and keep the keys pressed
3. Mount the battery at the same time (the keys are pressed)
4. The child lock function is now enabled
2. 3.
Unlock of Child lock
Press up and down keys of the 2nd row at the same time for one
sec.
When the blue LED turns on the handset is unlocked.
The handset is not unlocked If the keys are not released again
before the blue led turns off.
Lock
If no keys are pressed for 10 seconds, the handset will lock again.
Factory settings (disabled childlock)
Dismount 1 battery and wait 15 seconds. Mount the battery
and the HB is back to factory setting.