Linak DL8IC User manual

Page 1 of 28
LINAK.COM/DESKLINE
DL8 IC, DL9 IC, DL10 IC and DL11 IC system
User manual

Page 2 of 28
Contents
Preface ............................................................................................................................................3
Important information .................................................................................................................. 4
Safety instructions......................................................................................................................... 4
Safety issues............................................................................................................................... 5
Before installation, reinstallation or troubleshooting .................................................................... 6
Before start-up ........................................................................................................................... 6
During operation......................................................................................................................... 6
Misc ........................................................................................................................................... 6
Only for EU markets....................................................................................................................... 7
Only for Non EU markets .............................................................................................................. 7
Misuse .............................................................................................................................................7
Repairs ............................................................................................................................................8
Manufacturer’s declaration............................................................................................................ 8
Declaration of confirmity ............................................................................................................ 9
Misc. on the DESKLINE®DL8 IC / DL9 IC / DL10 IC / DL11 IC system ..................................... 11
Warranty .................................................................................................................................. 11
Maintenance ............................................................................................................................ 11
ETL-marking................................................................................................................................... 12
Description of the DESKLINE®DL8 IC / DL9 IC / DL10 IC / DL11 IC system............................ 13
Installation..................................................................................................................................... 14
Mounting guidelines for the DL8 IC / DL9 IC / DL10 IC / DL11 IC (foot part) ................................ 15
Mounting the feet...................................................................................................................... 15
Mounting the tabletop............................................................................................................... 18
Placing the monitor.................................................................................................................... 18
Connection................................................................................................................................ 19
Accessories and repair ................................................................................................................ 20
Disposal of LINAK products ........................................................................................................ 21
Labels ...........................................................................................................................................22
Drawing appendix......................................................................................................................... 23
Addresses....................................................................................................................................... 30

Page 3 of 28
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It
is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation.
Before our products leave the factory they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local dealer.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance
with the specifications, maintenance being done correctly and any repairs being carried out at a service centre,
which is authorised to repair LINAK products.
Changes in installation and use of LINAK products/systems can affect their operation and durability. The
products are not to be opened by unauthorised personnel.
The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S

Page 4 of 28
Important information
Important information on LINAK®products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safety instruction
General
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – risk of injury if these instructions are not followed.
The appliance is not intended for use by young children or infirm persons
without supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator is to
be fitted, there must be no possibility of personal injury, for example the
squeezing of fingers or arms.
Only the power supply type SMPS001, SMPS002 or SMPS006, shall be used
with the system.
The power supply shall not be covered while operating to allow sufficient
cooling of this appliance.
...to be continued

Page 5 of 28
Furthermore take care about the connecting wires from the power supply to the
DL8 IC / DL9 IC / DL10 IC / DL11 IC system, don’t damage this by overrun.
Assure free space for movement of application in both directions to avoid
blockade.
The appliance is only to be used with the power supply unit provided with
the appliance.
Safety issues
The builder of the equipment shall ensure that the use of the component
complies with relevant standards – like the Machine Directive. Care must be
taken to avoid squeezing of cables as it can cause movement of the system!
The SMPS001 / SMPS002 / SMPS006 must not be packed in heat insulating
material, but must be placed so that it can emit waste heat to the surroundings.
There are no ventilation holes to consider, the SMPS emits heat through its
surface.
Only the power supply type SMPS001, SMPS002 or SMPS006, shall be used
with the system.

Page 6 of 28
Before installation, re-installation, or troubleshooting:
• Stop the DL.
• Switch off the power supply and pull out the mains plug.
• Relieve the DL of any loads, which may be released during the work.
Before start-up:
• Make sure that the system has been installed as instructed in this User Manual.
• Make sure that the voltage of the control box is correct before the system is
connected to the mains.
• System connection. The individual parts must be connected before the control box
is connected to the mains. See the User Manual for LINAK actuators, if necessary.
During operation
• If the column makes unusual noise or smells, switch off the mains voltage
immediately.
• Take care that the cables are not damaged.
• Unplug the mains cable on mobile equipment before it is moved.
• The products must only be used in an environment, that corresponds to their IP
protection.
Misc.
The actuator system has a sound level below 55dB(A) in typical applications.
Updated manuals and declarations can always be found here:
www.linak.com/deskline

Page 7 of 28
Only for EU markets
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/
products, unless they are under surveillance or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the
safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play
with the product.
It is the operator’s responsibility to ensure that there is free space for the
application to move without risk for the operator or bystanders before
operating the application.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use.

Page 8 of 28
Repairs
In order to avoid the risk of malfunction, all DESKLINE®repairs must only be carried out by authorised LINAK workshops or
repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned
to authorised LINAK workshops.
Warning!
If any of the DESKLINE®products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE®systems do not withstand cutting oil.
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
LINAK A/S
Smedevænget 8
DK -6430 Nordborg
Herewith declares that LINAK DESKLINE®products as characterized by the following models and types:
Control Boxes CBD6S
Linear ActuatorsDB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23, LA31
Lifting ColumnsDL1A, DL2, DL4S, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15,
DL16,DL17, DL19, BASE1
Desk PanelsDPA, DPB, DPH, DPF, DPG1K, DPG1M, DPG1B, DPG1C, DPT, DP1, DP1CS,
DP1K, DP1V, DP1U
RF ControlsHB10RF,HB20RF, RFT, RFRL
Accessories BA001, SLS, Kick & Click
comply with the following parts of the Machinery Directive 2006/42/EC,ANNEX I,Essential health and
safety requirements relating to the design and construction of machinery:
1.5.1 Electricity supply
The relevant technical documentation is compiled in accordance with part B of Annex VII and that this
documentation or part hereof will be transmitted by post or electronically to a reasoned request by the
national authorities.
This partly completed machinery must not be put into service until the final machinery into
which it is to be incorporated has been declared in conformity with the provisions of the
Machinery Directive 2006/42/EC where appropriate.
Nordborg, 2017-12-08
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration
Manufacturer’s declaration

Page 9 of 28
DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
hereby declares that LINAK Actuator System composed of:
Lifting Column with integrated control, DLIC Master: DLXXXXXXMXXXXXX or
DLXXXXXXMXXXXXX
And
Passive Actuators, DLIC Slave DLXXXXXXSXXXXXX or
DLXXXXXXSXXXXXX
And
Control panel DP1C, DP1K, DPT, DPB, DPF, DP1L, DP1V, DPA, DPH, DP1U,
WDPL1
complies with EMC Directive: 2014/30/EU according to following standards:
EN 61000-6-1:2007, EN 61000-6-3:2007, EN 55022:2010 Class B
complies with Low Voltage Directive 2006/95/EC according to the standards:
EN 60335-1:2012
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
And
RF Control: RFRL00x, HB1xRF3000, HB2xRFx000; RFT000
complies with the Radio Equipment Directive 2014/53/EU:
EN 300220-2:2006, EN 61000-6-1:2007, EN 61000-6-3:2007,
EN 60335-1:2012, EN 62311:2008
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
Nordborg, 2017-08-25
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration
Declaration of confirmity
The RoHS mark is only applicable for the end product. Therefore, it must be obtained by the manufacturer of the
end products. LINAK®can, however, supply the required material information on our products.
For more information, visit: https://www.linak.com/about/declarations/
or contact: [email protected]

Page 10 of 28
Declaration of confirmity
DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
hereby declares that LINAK Switch Mode Power Supply, type SMPS006
complies with the EMC Directive: 2014/30/EU according to following standards:
EN 61000-6-1:2007, EN 61000-6-3:2007
complies with Low Voltage Directive 2014/35/EU according to the standard:
EN 61558-2-16:2009
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
This declaration of conformity is issued under the sole responsibility of the manufacturer

Page 11 of 28
Misc. on the DESKLINE®DL8 IC / DL9 IC / DL10 IC / DL11 IC system
This system is a DESKLINE system developed for desks and for indoor use in offices. Do not use it in industrial kitchens or in
other enviroments that have to be cleaned with aggressive detergents.
Do not bolt the legs to the floor so that free movement is prevented. This could cause serious damage to the legs in fault
situations.
Warranty - 60 months on DESKLINE®
This will be valid for all DESKLINE®products produced after the 1st of May 2015.
Products produced before 1st of May 2015 will still be covered by 36 months.
Products used in DESKLINE application: If these products are used in another application, they will be covered by 18 months
warranty.
If there is any doubt that returned products are within the warranty period it is to be treated as if they are covered by the
warranty. We recommend that you use the date of the Control box or actuator as reference if possible.We will have our
purchase no. printed on the label.
Maintenance
Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.
Service of double-insulated products:
Class II
A Class II or double insulated electrical appliance is one which has been designed in such a way that it does not require a
safety connection to electrical earth (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an
electric shock and that this is achieved without relying on an earthed metal casing. This is usually achieved at least in part by
having two layers of insulating material surrounding live parts or by using reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be added to the
product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double insulation symbol
(a square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace.
The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

Page 12 of 28
C/N 4008003
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008004
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008005
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008671
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4009507
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
ETL-marking
Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.
C/N 120690
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United
States
C/N 9901916
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United
States

Page 13 of 28
Description of the DESKLINE®DL8 IC / DL9 IC / DL10 IC / DL11 IC system
Application of the DESKLINE®DL8 IC / DL9 IC / DL10 IC / DL11 IC system:
Irrespective of the load the duty cycle 10% ~ max. 2 min. at continuous use stated in the data sheets, must NOT be
exceeded as this will result in an overheating of the motor and control box. Exceeding the duty cycle will result in a dramatic
reduction of the life of the system.
A typical DL IC system consists of:
• 2 lifting columns DL8 IC, DL9 IC, DL10 IC or DL11 IC
• Power supply SMPS001, SMPS002 or SMPS006
• Desk panel DPA, DPB, DPH, DP1K, DPF1K
• Exchangeable cables

Page 14 of 28
Installation
Mounting guidelines for the DESKLINE DL8 IC / DL9 IC / DL10 IC / DL11 IC system
The motor housing is supplied with six M6 threaded holes for mounting on the top frame.
1. Mount motor housing on top frame using six M6 screws with the following specifications:
Quality: Min. grade 8.8
Length: Max. 10 mm (plus top frame thickness). The screw must not go further than max. 10 mm into the motor housing
2. Fasten screws thoroughly (torque: max. 7.5 Nm).
Always use six M6 screws for mounting
the motor housing on the top frame
Mounting screws must not go further than
max. 10 mm into the motor housing
Sufficient stability of the desk is only obtained if all six M6 screws are used for mounting the motor housing on the
top frame.Tests with fixing the motor housing using only four M6 screws have proved that the torsional stability of
the desk this is insufficient.
LINAK recommends using the DL IC DESKLINE®system in push applications with the motor housing mounted upwards.
Alternatively, use the Kick & Click™ top frame and avoid screws to get easy desk assembly.

Page 15 of 28
177
4xM6
29.7
29.7
Ø42
97
35.4
Foot
Mounting guidelines for the DL8 IC / DL9 IC / DL10 IC / DL11 IC (foot part)
DL8 IC / DL9 IC
The DL8 IC / DL9 IC bottom plate is supplied with four M6 threaded holes.
1. Mount column bottom on desk feet using four M6 screws with the following specifications:
Quality: Min. grade 8.8
Length: Min. 10 mm (plus foot thickness);
Max. 20 mm (plus foot thickness)
2. Fasten screws thoroughly (torque: max. 10 Nm).
The holes in the foot must be sufficiently larger than ø6 to ensure space for the screw heads to be screwed fully into the foot.
DL8 IC / DL9 IC bottom plate

Page 16 of 28
DL10 IC
The DL10 IC bottom plate is supplied with four M6 threaded holes.
1. Mount column bottom on desk feet using four M6 screws with the following specifications:
Quality: Min. grade 8.8
Length: Min. 10 mm (plus foot thickness);
Max. 16 mm (plus foot thickness);
2. Fasten screws thoroughly (torque: max. 10 Nm).
The holes in the foot must be sufficiently larger than ø6 to ensure space for the screw heads to be screwed fully into the foot.
DL10 IC bottom plate
Column bottom mounted on desk foot

Page 17 of 28
DL11 IC
The DL11 IC bottom plate is supplied with four M6 and two M8 threaded holes.
1. Mount column bottom on desk feet using four M6 or two M8 screws with the following specifications:
Quality: Min. grade 8.8
Length: Min. 10 mm (plus foot thickness);
Max. 16 mm (plus foot thickness) for M6
Max. 14 mm (plus foot thickness) for M8
2. Fasten screws thoroughly (torque: max. 10 Nm).
The holes in the foot must be sufficiently larger than ø6 to ensure space for the screw heads to be screwed fully into the foot.
DL11 IC bottom plate
Column bottom mounted on desk foot (left: M6; right: M8)

Page 18 of 28
Recommended placement of an iron plate/tube or another magnetic material
Placement of a monitor directly above the motor housing may cause malfunction of the monitor.
Magnets inside the motor may interrupt the picture on the monitor depending on the distance and type of monitor. If this is
the case, the problem may be solved by placing an iron plate/tube or another magnetic material, somewhat larger than the
motor housing, between the motor and the tabletop.
Mounting the tabletop
The sound from the lifting column spreads as vibrations to the tabletop which amplifies the sound.
This can, however, be reduced.
1. Place vibration / shock-absorbing material between tabletop and top frame.
Placing the monitor
Assembled desk

Page 19 of 28
Connection:
Items required:
Motor cable SMPS + cable
Desk panel (example)
1. Connect the master and follower columns using the motor cable.
2. Mount the desk panel onto the desk and connect it to the master column.
3. Connect the SMPS to the master column and to the mains.

Page 20 of 28
Accessories and repair
Ordering accessories
Order from your nearest LINAK®dealer or subsidiary.
Accessories
Please contact your nearest LINAK dealer for information.
Repairs
Systems should only be repaired by an authorised LINAK service centre or engineer. Systems to be repaired under warranty
must be sent to an authorised LINAK service centre.
Warning!
By unauthorised opening of the system there is a risk that it may malfunction at a later date.
Spare parts
Please contact your nearest LINAK dealer for information on spare parts.